Search Documents

By MKS Vel, S. Mukhopadhyay, R. Mishra

Off late, the criteria of selecting the refractory have acquired a trend line aiming to a cleaner environment and the utmost importance is given to the eco-friendly approach. The stainless steel making furnaces normally use mag-chrome refractories for the obvious reasons of changing slag basicity from acidic to basic. Such refractories generate toxic fumes and compounds with hexavalent chrome, which is unhygienic if inhaled. The present paper describes the development of a chrome free alumina magnesia carbon refractory, it's different test properties, simulative testing and microstructures. The optimum quantity and distribution of carbon in the brick restricts the carbon pick-up by the steel. Bricks with the same composition were manufactured in the commercial scale and used in a stainless steel making furnaces in USA. The performance of same refractory in this furnace was quite encouraging and at present the same quality brick has become a normal practice in this furnace. Since no chromite is used in making this brick, so no toxic compounds are generated environment remains pollution free.

Jan 1, 2004

By F. Bélanger, P. Fournier

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northeast of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 60,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill. This paper will highlight the impact of a pre-detox thickener on the cyanide consumption in a gold leach/CIP circuit. While the pre-detox thickener was built with the intention to reduce the cyanide consumption, the opposite effect was observed when the thickener was put temporarily offline. It will show how the re-circulation of a dilute stream of cyanide into the grinding circuit, increases the overall slurry temperature and by the same effect, increases the dissolved copper concentration in the leaching circuit which subsequently increases the cyanide consumption.INTRODUCTION The processing plant is using a conventional gravity, cyanidation and carbon-in-pulp processing facility currently operating at approximately 60,000 mtpd. The comminution process is based on two parallel SABC lines, each fed from an individual reclaim tunnel. Cyclone overflow from the two ball mill circuits is directed to the pre-leach thickener. The thickener underflow is distributed to two (4) parallel leach trains of 5 tanks each, each leach train providing 29 hours of leaching retention time. After leaching, the gold in solution is recovered in a carrousel CIP circuit consisting of two (2) parallel leach trains. Tails from each CIP circuit are combined and sent to a pre-detox thickener to recover as much cyanide solution as is economically practical before being diluted and fed to a cyanide destruction system. The detoxified tailings are sent to the Tailing Management Area (TMA) for settling and retention. The excess water from the TMA is reclaimed and recycled back to the processing plant. The pre-detox thickener is designed to thicken the leach tails slurry to 64% solids with the overflow being recycled to the grinding circuit. It is estimated that the pre-detox thickener will recover 60% of the cyanide in the CIP discharge solution. It is also designed to reduce the SO2 consumption by diluting the thickener U/F to 50% solid using the tailing pond reclaim water which has very little cyanide content."

Jan 1, 2019

By L. Hacini

The start-up is the most critical phase of the cell life, as an uncontrolled start-up could lead to early infiltrations, instabilities, and in some cases to the cell death. Lots of efforts are put to increase the lifespan of cells, as it has a major impact on both the operating costs and the environmental footprint of the aluminum industry. Obviously, a true size test on a cell is a resources- and time-consuming approach that could be used only to validate mature concepts. Moreover, numerical modelling is a low-cost and versatile tool capable to test a wide range of potential ideas and concepts. In the present article, a thermal electrical mechanical slice model is presented. This model describes the preheating and bath periods of a P155 aluminum cell start-up, as used at the Grande Baie smelter. The impact of sodium diffusion and expansion is also included in the model. This model will be useful to study different problematical issues such as the global behaviour of lining materials, shell and cradle deformations during start-up and several start-up scenarios. Such a model will also be able to answer some interrogations regarding early infiltrations and their impact on the lifespan of the electrolysis cell.

Jan 1, 2011

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By Holt. Grover J.

"IntroductionThe history of iron ore production in the United States has followed a pattern not far different from that set in the production of non-ferrous ores; the first interest of the prospector and miner being the discovery and development of high-grade ores. In the early stages of development of most mining districts, high-cost low-grade ores are usually of slight interest due to the additional capital investment required in concentrating plants, as well as the increased requirements of •power and other facilities. As the reserves of higher grade ores are depleted and the technical knowledge of ore beneficiation is broadened, production of concentrates from the lower grade ores is stimulated.The real stimulus necessary to arouse serious consideration of beneficiated iron ore in the Lake Superior district has been provided by the serious inroads made in the high-grade ore reserves by two World Wars.The first shipment of high-grade iron ore from the Mesabi range in Minnesota was recorded in 1892, and the first token shipment of concentrates was made 15 years later, in 1907. Not until 1910 did the production of concentrates assume any great importance. A steady increase in concentrate production over the years is shown by the fact that, in 1910, concentrates accounted for 8 per cent of the total shipments from the State, whereas by the time of World War II this percentage had increased to 22 per cent and by 1948 had risen to 26 per cent. It seems a safe assumption that the shipment of concentrated iron ore, from the Mesabi range in particular, will continue to increase even more rapidly from now on, with other iron ranges of the Lake Superior district following this lead."

Jan 1, 1950

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

By M. B. Mansur, A. S. Guimarães, A. J. M. Santanilla, D. C. R. Espinosa, J. A. S. Tenório, R. A. Pini

The separation of Ni and Co from sulphate medium containing Mn, Mg, Cu and Ca was carried out by solvent extraction. The object of this study was to investigate the synergistic effect using phosphinic acid (Cyanex 272) and carboxylic acid (Versatic 10) and their mixtures in kerosene. The extraction percent of each metal ion was found to increase with increasing pH and extractant concentration. Co was preferentially extracted over Ni under the same extraction conditions. The separation factors of Ni/Co increased with the use of the synergistic systems investigated.

Jan 1, 2014

By S. Ivanova

The results presented in this paper show that the gold solution dilution is a key parameter to control the dispersion of gold on ?-Al2O3 the selected support. The variation of concentration leads to changes in pH which modify the nature of gold complexes from HAuCl4 formed in the solution. These complexes are presented. Some of them (AuCl3(OH)- and AuCl2(OH)2 -) react with the surface of alumina and give interesting interaction. AuCl2(OH)2 complex has been considered as an ideal complex because of the strong anchorage of a bidentate species on the alumina. This complex is formed mainly in a solution of gold with a concentration of 10-4 M giving a pH of 3.5-4.5. The nature of the anchorage and the amount of chlorine, has an influence upon the formation of Au-Cl bridges which modify the dispersion of the gold on alumina of the final catalyst as shown by TEM.

Oct 1, 2003

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By D. Saramak, T. Gawenda, Z. Naziemiec, A. Saramak

"Crushing and grinding operations are burdensome to the environment due to generating large amounts of dust, noise and waste during course of comminution operations. An indirect negative contribution of industrial crushing processes is an increase of carbon dioxide emissions, which is a byproduct in energy production processes. On the other hand comminution processes in ore enrichment technology are essential due to liberation the useful minerals from the gangue, and producing the demanded particle size fractions of products. The article concerns investigation over negative influence of comminution devices on environment in terms of dust and noise emissions. Several various crushing devices were under investigations, both in laboratory and in industrial scale.The obtained results were analyzed in terms throughput and energy consumption achieved in various crushing devices. The test results allow to conclude that an intensity of dust generation for individual types of crushing devices is varied. An additional aim of this article is to link the aspect of mineral processing with its environmental impact and hence an influence of raw materials beneficiation industry on the quality of life of residents in immediate and close vicinity.INTRODUCTIONMineral raw materials beneficiation processes are an integral part of multi-stage processing of coal, iron ore and non-ferrous metals, production of aggregates, cement, or precious metals and stones. One of the common features of all beneficiation operations is their high energy consumption, which is mainly connected with various operations of feed particle size reduction. Comminution processes in ore enrichment technology are essential to expose and liberate the useful minerals from the gangue, while in aggregate production processes – to obtain the demanded particle size fractions of products. Crushing operations are characterized by a high degree of negative impact to the environment and humans, mainly due to:• High electricity consumption, which indirectly contributes to the increased emissions of carbon dioxide into the atmosphere, since CO2 is often one of the byproducts of energy production;• Relatively rapid wear of device working parts, what forces a production of spare parts and involvement of steel industry;• Intense dust pollution generated during crushing and grinding processes. This is one of the factors affecting the air quality and the consequent deterioration of the living conditions of inhabitants near mines and processing plants; and • Excessive noise emissions."

Jan 1, 2016

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015