Search Documents

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939

By W. Leblanc, J. Phalen

This paper tells the story of a serious mine fire on a mechanized longwall face in a submarine coal mine at Glace Bay, Nova Scotia. The story gives, in chronological order, a technical account of the steps taken to investigate, fight and contain the fire. The time during which the events took place spans from June 19 to November 7, 1975.

Jan 1, 1976

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By H. H. Bird

Kilembe is situated in the foothills of the Ruwenzori Mountains in Uganda. Precambrian stratiform copper de-posits are currently being mined at a rate of 90,000 tons per month. Complex ore structures and variable ground conditions have led to diverse mining methods in the past. New mining areas contain more shallow-dipping, highly contorted orebodies, in heavy ground. Cut-and-fill mining will be practised in the future. The geology, mining and milling are described.

Jan 1, 1968

By A. G. Ballachey

Introduction This paper will describe the mining plant and underground operations at Quemont. Details of geology and milling are beyond its scope. Papers on these subjects will be prepared and presented separately. A detailed account of the exploration and development, 1944 to 1947, has been given by W. L. Brown (1). Location The mining concessions of Quemont Mining Corporation, Limited, are in Rouyn township, Rouyn-Noranda county, northwestern Quebec. These concessions total about 640 acres in area. They lie within the limits of the City of Noranda, contiguous to, and directly north of, the Horne mine of Noranda Mines, Limited. A large area in the southern part of the property is covered by the north arm of Osisko lake. Production The present operating rate is about 2,100 tons per day. Three flotation concentrates are produced: copper, containing a large proportion of the gold and silver in the ore; zinc; and pyrite, which carries an appreciable additional proportion of gold. The copper and zinc concentrates are shipped to smelters as produced. The pyrite concentrate is cyanided to recover additional gold, after which it is filtered, dried, and shipped for the manufacture of sulphuric acid. The principal revenue metals are copper, gold, and zinc. Silver and pyrite are important by-products.

Jan 1, 1952

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By J. Ouellet

"ABSTRACTA brief background on in-situ testing of mine backfill, as well as pressuremeter testing is briefly described, and results from an in-situ testing on paste backfill are presented. A series of self-boring pressuremeter tests were done from the top of a backfilled stope in an underground mine. The tests were conducted along a 20-metre vertical line in the centre of the stope. Some 14 tests were performed along this depth. The instrument used was a Camkometer built by Cam Insitu, Cambridge. The instrument proved to be efficient and reliable for underground testing in a cemented paste backfill. The testing program was conducted within the planned schedule with a high success rate. The test done in this study permitted the measurement of paste backfill strength, stiffness and in-situ horizontal stress within the backfill. RésuméUn bref historique des essais in situ dans le remblai minier est présenté. L’essai pressiométrique est décrit succinctement et des résultats d’une campagne d’essai dans un remblai en pâte sont présentés. Un programme d’essais au pressiomètre auto-foreur a été réalisé à partir du sommet d’un chantier remblayé sous terre. Les essais ont été réalisés le long d’un ligne vertical d’environ 20 mètres pour un total de 14 mesures. Le Camkometer de la firme Cam Insitu de Cambridge a été utilisé. Cet instrument s’est avéré efficace et fiable pour tester le remblai en pâte cimenté sous terre. Le programme d’essai s’est déroulé à l’intérieur de l’échéancier prévu avec un taux de réussite élevé. Ces essais ont permis de déterminer la résistance, la rigidité de ce remblai ainsi que les pressions in-situ prévalant dans le remblai."

Jan 1, 2000

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By G. E. Viens, R. A. Campbell, G. N. Banks

A survey of the literature reveals wide differences in the procedures used in making iron ore pellets and in the properties of the pellets obtained. In this paper, the methods of production and the properties of pellets, as reported in the literature, are examined in an effort to determine what correlations exist between them. An attempt is also made to determine the levels of the properties of pellets which are considered acceptable and desirable in modern practice. M UCH has been written regarding the important changes which have been taking place recently in the iron ore industry. As the demand for ore has increased and the supply of direct-shipping ore has dwindled, tl1e problems associated with the utilization of lower grade ores ha\•e been intensely investigated and important advances in both beneficiation and agglomeration techniques have taken place. In particular, there has been a great deal of activity in connection with the pelletizing method of agglomeration. The superiority of pellets over raw ore has been demonstrated in blast furnace tests

Jan 1, 1962

By Frank D. Shepherd

THE Gunnar Gold Mines property is on the west shore of Beresford lake, in the Rice Lake mining division, southeastern Manitoba. Gold was first discovered in place in the Rice-Beresford Lakes area in 1911 on the Gabrielle claim, now included in the San Antonio Mines property at Rice lake. Following an eastward trend of favourable prospecting ground, promising showings were next staked in the vicinity of Long lake during the years 1915 and 1916. At that time, William Walton and associates, among them Gilbert LaBine, staked the Eldorado vein, north of Long lake, and Eldorado Gold Mines, Limited, was formed to develop the property a Company that, later, was to become widely known through successful operation of its radium-silver mine at Great Bear lake, Northwest Territories. Continuing eastward from Long lake, Walton and his partners, Gunnar Berg, Leo Seaberg, and Wm. Quesnel, staked claims during the years 1920-24 in the vicinity of Beresford lake which, later, were to become incorporated into the Gunnar Gold Mines property. The presence of gold-bearing quartz on these claims had been known from the time they were staked, but an opportunity to consolidate them into a group was not forth-coming until early in the year 1933. Although promising gold showings had been disclosed during the performance of assessment work on individual claims, no continuous mineralization having mine-making possibilities was discovered until after the consolidation of the entire group. From this stage onward, progress was rapid. Active exploration was begun on August 1st, 1933, and late in October James Houston reported favourably on the property. On October 27th, Gunnar Gold Mines, Limited, was incorporated in the Province of Ontario to develop and operate the property. The Company is also registered in Manitoba. The authorized capitalization is 3,000,000 shares of $1.00 par value. Gilbert LaBine was appointed president of the Company, with James Houston as mine manager. Following completion of a diamond-drilling programme, planned in 1933, it was decided to install a mine plant capable of carrying development to a depth of 1,000 feet. A transmission line, 5 miles in length, was built to the Great Falls-Central Manitoba line of the Manitoba Power Company, Limited.

Jan 1, 1939

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934