Search Documents

By Andrea R. Gerson, Roger St. C. Smart, Russell Schumann, Joan E. Thomas, Warwick Stewart, Stuart Miller

Sequential Net Acid Generation (NAG) accelerated oxidation testing using peroxide was carried out on single sulfide mineral samples. The calculation of the nett acid production potential (NAPP) assumes that all the sulfide is present as pyrite and that dissolution results in a 2:1 ratio of H+:SO42-. NAPP as kg H2SO4/t is calculated as 30.6 x wt.% S present. To test whether this calculation is valid a NAPP* value was defined in which instead of using the wt.% S present for the calculation the wt.% S dissolved is used. Stoichiometric analysis of the dissolution products of the sulfide minerals as they would occur at pH 7 indicates, that in all cases, the ratio of H+:SO42- of 2:1 is viable. The NAG to pH 7 and NAPP* closely coincided for pyrite, bornite, chalcocite and covellite. For the three Cu-containing minerals, the NAG to pH 4.5 value was 0 as is predicted on the basis of the speciation likely to be present at pH 4.5. Acid generation is due to hydroxylation of the dissolved Cu between pH 4.5 and 7.0. The NAG to pH 7 and NAPP* values for chalcopyrite, arsenopyrite and pyrrhotite were in reasonable agreement but were not for either sphalerite or galena. Zn is not completely hydroxylated at pH 7 as is assumed by the calculation. For galena, surface analysis identified polysulfide formation on of the leach residue polysulfide. The formation of polysulfide is an acid consuming reaction. Therefore under conditions of accelerated oxidation the NAPP value is a reasonable estimate of the possible acid production in all cases except for sphalerite and galena. However, under conditions of less intense oxidation, for instance in columns, waste rock and tailings dumps, the formation of polysulfides is likely to be more widespread thus reducing the correlation between NAPP and the maximum possible acid production.

Jan 1, 2004

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By J. Ander

About fifteen years age some mines in western Canada commenced using Diesel engines, partly for development work but also for operations on quite a large scale. In the Eastern mining field, the Diesel engine made its appearance some eight years ago and has since, at quite a number of mining plants, proved to be a reliable and economical prime mover. As a result, it is today used more extensively than could have been foreseen only a few years ago, and it is reasonably safe to predict that the next few years will see the Diesel engine utilized to a still greater extent in the Canadian mining industry. It is not much more than thirty years since the first Diesel engine was put in operation. During the early years of this century, the Diesel engine took, so to say, its first faltering steps in public service. Since then it has reached a high state of perfection, and its importance has grown in a most remarkable way, until today it is used in practically every field where power is required. It is slowly but surely superceding steam for a great many purposes, as, for instance, for ship propulsion. While in 1921 only about 8 per cent of all tonnage launched was motor-driven, the proportion had grown to 38 per cent in 1927, and for 1929 it was slightly over 45 per cent. Some of the finest passenger liners afloat are Diesel-driven. In the early days, Diesel engines were built only in comparatively small units. Today engines with a capacity per unit of up to 10,000 horsepower, or even more, are being built for marine and stationary purposes.

Jan 1, 1930

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By J. Edwin Van Buskirk

For a country that is as important a gold producer as Canada, the return to the gold standard of the major commercial countries of the world during the past five years is of particular significance. To the Canadian gold mining industry, the advantages of the gold standard are a matter of more than theoretical importance. According to economic theory, prices are determined by the relation between the demand for, and the supply of, money. The demand consists of the offering of goods for money; the more goods offered, the greater the demand. The supply consists of the total money available for the purchase of goods. The total supply of goods to be exchanged through the instrumentality of money remaining the same, an increase in the supply of money will, according to this theory, raise prices; conversely, a decrease in the supply of money will lower prices. Let us imagine that everyone in the world suddenly had twice as much money, and that the sum total of all goods remained the same. Is it not obvious that we would pay just double the price for these goods? In Canada today, most people have approximately 50 per cent grea.ter income than in 1913, and the average price for all articles sold in Canada is 50 per cent above those in 1913.

Jan 1, 1928

By J. O. Marsden

Over the past decade, the copper industry has been through an extended downturn followed by several years of sustained high copper price. A number of new technologies have been developed over the past 10 years aimed at reducing costs by decreasing energy, labor, and materials requirements, or by increasing metal recovery. The energy intensity of different copper extraction routes and different technologies varies considerably and this has a significant impact on the economics of extraction. Based on average ore grade materials, the total energy for the extraction of copper typically varies from about 24-26 MJ/lb (6.7-7.2 kWh/lb) for the mining, crushing, milling, flotation, smelting and refining route to about 14¬16 MJ/lb (3.9-4.5 kWh/lb) for the mining, crushing, heap leaching, solution extraction and electrowinning route. New technology developments are providing opportunities for significant reductions in energy consumption for copper extraction, representing energy savings up to 20-25% in some cases. In addition, in many cases, these new technologies have introduced environmental, safety and health benefits over the incumbent technology. Some of these technology developments have been more successful than others, and many hold great promise for application in the coming decade. This paper provides an overview of the technology developments that have occurred, and explores the underlying reasons behind successful implementation.

Jan 1, 2007

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By Rodolfo Zanella

Au/TiO2 catalysts were prepared by deposition-precipitation using NaOH (DPN) (~3 wt % Au) and urea (DPU) (~8 wt % Au), and calcined at various temperatures between 100 and 400 °C. They were characterized by UV-Visible, XANES, EXAFS and TEM. Their activity were tested in the reaction of CO oxidation at 5°C. After preparation, the gold species are in the oxidic state III. They begin to transform into metallic gold under air at ~100 °C for DPN and ~150 °C for DPU. At 200 °C, all the gold is metallic for the two preparation methods. The particle size increases from 1.5 to 3.5 nm with the calcination temperature. The catalytic activity for CO oxidation increases with the percentage of metallic gold, and it is maximum at 200°C for both types of samples. The activities (per mole of Au) are the same for the two types of catalysts. At higher temperatures, the catalytic activity drops. The decrease of activity is mainly due to a change of particle shape with the calcination temperature rather than to the increase of the particle size. At a calcination temperature of 200°C, the particles present small facets with rounded parts, and their outer surface contains a large proportion of low coordinated sites (steps and corners) while at high temperature of calcination, they are truncated octahedra with smooth facets.

Oct 1, 2003

By Ajit K. Sinha

"Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentaryhosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3070 to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By John E. Callahan

"A stream sediment geochemical survey covering an area of 13.000 sq. km near Churchill Falls. Labrador. was conducted for Brinex (British Newfoundland Explorations Ltd.) prior to partial flooding by the Churchill Falls power project. Stream sediments (minus 80-mesh) were analyzed for Cu, Pb, Zn, Ni, Ag, Mo. U and Mn, and the heavy mineral, nonmagnetic fraction (minus 60-mesh) for Cu, Pb, Zn, Ni, Ag, Mo, Ba and Mn. A binocular examination of the concentrates for sulphides and pyrope garnet was done on the heavy mineral concentrates. The concentrates were also examined for fluorescent minerals.Two distinct areas with high trace-element values indicate the need for follow-up studies. The first is in an area of gabbro erratics containing massive and disseminated sulphides (pyrrhotite, pyrite and minor chalcopyrite) on the western edge of the survey area along the Esker Road. The second, largest area (several hundred square kilometres) is anomalous in U and Mo and associated with felsic intrusives (Red Wine Complex?), syenites. granite gneiss and sedimentary rocks (Seal Lake Group?).The binocular study showed that almost 15% of the heavy mineral concentrates contained pyrite and no other sulphides. This indicates that this technique may be worthwhile in determining the presence of sulphide minerals in stream sediments from glaciated environments. The only fluorescent mineral observed in the study was zircon."

Jan 1, 1981

By Fathi Habashi

"A process is proposed for the treatment of phosphate rock for the recovery of uranium and the lanthanides. The process assures the production of phosphatic fertilizers without polluting the environment with radioactive material.IntroductionWhile many processes for uranium recovery from phosphoric acid produced by the H2S04 route are known and utilised commercially, little is known about uranium recovery from phosphoric acid produced by the HN03 route1. Advantages of the latter route are both the elimination of the gypsum disposal problem, and the possibility of radium disposal in a controlled way2. Further, the lanthanides originally present in the rock can be recovered if the nitric acid route is used; they will be mostly lost in the gypsum produced by the sulphuric acid route3. In the present work a scheme for the recovery of uranium and the lanthanides from phosphate rock without interfering with the normal route for fertiliser production is proposed using HN03 as a leaching agent. Attention was also given to uranium decay products and their separation so that they might not contaminate the fertiliser4. Further, an attempt was made to defluorinate the leach solution in order to upgrade the fertiliser and at the same time recover the fluorine5. Rapid analytical methods for the determination of uranium, radium, and lanthanides in phosphate rock were developed6,7."

Jan 1, 1997

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By J. H. D. Hargrove, A. F. Snowball

Atmospheric pollution control has become increasingly important in re-cent years with laws and public opinion having required the reduction of contaminants from industrial gas effluents. Treatment methods have advanced to make possible, with proper plant design and operation, a satisfactory removal of these contaminants. Gases from Cominco's metallurgical operations at Trail, approximating 900,000 c.f.m., are treated by baghouses, electrostatic precipitators, cyclones, or wet scrubbers. The tabulated data include gas and dust conditions, plant performance, and some details of plant equipment. Discussion emphasizes the special features, scope of application, and basic design principles of the treatment methods, all based on Cominco experience. Recovery of over 99 per cent of the fume and dust is achieved by the major installations from which effluent gases go to atmosphere. Cooling of gases for baghouse recovery and conditioning for electrostatic precipitation are mentioned. Co3ts are tabulated for some of the installations on the basis of a unit of 1,000 cubic feet of gas. Suggestions are made on the procedure for assessing a smoke treatment problem and for selection of suitable equipment.

Jan 1, 1959

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By R. von Gal

Hazelett Strip-Casting Corporation has been producing the Hazelett® twin-belt casting machines for copper casting since the mid-1960s. The first commercial casters were developed for copper alloy strip and anode plate. In 1968, development work was started to adapt the twin-belt caster for copper bar casting to be rolled in-line into wire rod. Since then, 36 casters have been sold as part of the CONTIROD® system for the production of a substantial portion of the world&apos;s copper rod supply. A unique feature of the twin-belt caster is the mold&apos;s ability to comply with the size and shape of the cast bar as it shrinks during solidification. Maintaining contact between the mold and the bar provides a high rate of heat transfer as well as other benefits, including the prevention of surface imperfections caused by remelting in the mold. This paper will give an overview of the continuous evolution of the twin-belt caster technology with an emphasis on recent developments in compliant mold technology for copper casting.

Jan 1, 2007

By William A. Price

The objective of this paper is to outline the approaches used in British Columbia to address the challenges posed by metal leaching and acid rock drainage (ML/ARD). Challenges include the large financial costs, the need for site-specific assessments, the large information requirements, the need for mitigation measures to be designed and financed in a manner that permits long-term performance, the lack of long-term operating experience, the ongoing changes in many important processes, the need for pro-active detection and resolution of concerns, difficulties in predicting the potential for ARD or significant metal leaching, the need for new tools, and the multidisciplinary, highly specialized nature of the work. Consequently, mines must be planned, operated and closed in a manner that permits regular review, detailed monitoring and adaptive management. Proper consideration of the challenges involved, including a plan of how all outstanding concerns will be addressed, studies to address areas of significant uncertainty and caution in the absence of the required understanding, should ensure environmentally safe practices in the future.

Nov 1, 2002

By James R. Yeager, Eric L. Hoffman, John R. Clark

"Abstract -This paper describes fire assaying and ‘high tech’ alternatives for gold analysis, including advantages and disadvantages of each method. These ‘high tech’ methods include INAA (instrumental neutron activation), aqua regia digestion/AA (atomic absorption), GFAA (graphite furnaceatomic absorption) or ICP/MS (inductively coupled plasma emission mass spectrometry) and a combination of cyanidation with AA, GFAA or ICP/MS methods.Fire assay remains the stalwart among analytical methods for gold but, even with its multiple analytical finishes, is not fool-proof for recovering 100% of the gold present. Consumers of assays should not blindly trust the assay results without consideration of quality control data. Laboratories can and do make mistakes. Some of these can be easily discovered if you do your own due diligence. All these measures should ensure that gold analysis values from successive campaigns and from different laboratories meet acceptable levels of accuracy and precision, and can be correlated together, particularly when they occur in neighboring holes. This is essential just as much for prospect evaluation as for project feasibility."

Jan 1, 1998