Search Documents

By J. F. Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with bucket-line excavator mounted upon it, which has developed to a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant to work economically the shallower gold gravel deposits that the bucket-line dredges do not work. The dragline dredge consists of the drag-line excavator, on caterpillar mounting on the edge of the dredging pond, which feeds the gravel to the washing plant, mounted on a floating barge in the pond. There have been more than twenty-five such plants built and operated in central and northern California and an unknown number in other States. There have been variations in details of design but the essentials are similar in all. I wish to describe the operation of a typical drag-line dredging plant, that of the Wyandotte Gold Dredging Company on the Farnan Ranch in the Oroville district. This organization of six active partners built their first plant on Wyandotte creek in the autumn of 1933. The operation was successful due to wise management, which was based upon good plant design and proper principles of operation. The partners elected one of their number, H. F. England, as manager with full control and responsibility. This plant and operation furnished the pattern for many subsequent ones.

Jan 1, 1937

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By Victor F. Hollister, Robert W. Hodder

"The petrology and mineralogy of porphyry copper deposits are thoroughly described in recent literature and cited as the definitive characteristics for this type of deposit. The magmatic-hydrothermal aspect of genesis is also dealt with in detail. However, descriptions of their internal structure and regional setting are not as rigorous, and the genesis of this structure is simply stated as the release of high fluid pressures in a cooling magma emplaced along large fault zones. Genetic relationships between internal structure, regional setting and the tectonic evolution of continents has been alluded to infrequently in the past, but can now be considered together within the developing concept of orogeny at the margins of drifting crustal plates.Tensional structures, on both local and regional scale, and a Triassic to Tertiary age are described for porphyry copper deposits. We contend that such structure and age are distinct and unifying characteristics for this type of deposit and are genetically related to major crustal movements. British Columbia has porphyry copper deposits contemporaneous with plutons 180 to 200 million years old and 40 to 60 million years old. The former age group correlates with early stages of the continent's westward drift, and the latter group with a change in tectonic style during late development of the Canadian Cordillera. Hence, one can in British Columbia reflect on the genesis of a deposit's structure in the broader context of tectonic evolution. Such consideration should lead to more definitive criteria for area selection in exploration."

Jan 1, 1972

By G. Mousavian, R. Bagheri, N. Dalili

Polypropylene (PP) and its composites have an increasing use in automobile and domestic industries. Since the published results on strain rate effect on yield behavior do not match, and there is a high attention paid for effect of nanometeric fillers on deformation behavior of composites, in this research the strain rate effect on yield behavior of PP and the effect of nanometeric fillers on deformation behavior of PP have been studied. Microscopic observations and tensile tests in different strain rates on neat PP samples and on samples filled with 5, 10 and 15 %wt have been used. A dramatic change in behavior for the modulus and post-yield slope curves when the strain rate is between 0.0433-0.05 s-1 has been observed. Microscopic observations on PP indicate a change in deformation mechanism from shear yield to crazing at the same strain rate that the change in behavior of curves occurs. It has been observed that in PP nanocomposites with higher amount of calcium carbonate, fracture in early stages of deformation occurs in lower strain rates. In other words for a fixed stain rate there is a critical filler percentage such that if the filler percentage is higher then early-stage fracture will occur. Similarly for a fixed filler percentage there is a critical strain rate and in higher strain rates early fracture will occur. The critical stain rate will decrease as the filler percentage increases and vice versa.

Jan 1, 2006

By W. G. Robinson

"MINING is one of Canada's most important industries and exploration is the life-blood of this dynamic and exciting business. The health and growth of the mining industry of tomorrow depends on the effort and thought that go into exploration today. The Members of the Geology Division of the C.I.M. are directly concerned with exploration, and it is fitting that this Division should periodically sponsor reviews of the thoughts and practices of the exploration com-munity. Accordingly, we have invited seven leading authorities to contribute papers dealing with specialized aspects of this field.Exploration is a science, or art if you will, that is constantly changing in keeping with our expanding knowledge of geology and technology. It started with the old-time prospectors who searched the wilds for exposures of ore, and made finds that developed into some of our most important mining camps. As more discoveries were made, they were able to relate certain types of deposits with particular geological conditions, laying the foundation for modern concepts of economic geology. The mapping by the early field parties lacked detail and usually served to outline the ""greenstone"" areas considered favourable for prospecting. More de-tailed studies through the years by government and company geologists led to new thoughts on the origin, emplacement and geological control of orebodies. The continuing diversity of opinion on these subjects indicates a need for further research, but each year sees an increase in our reserves of factual information."

Jan 1, 1967

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By Katherine (Kate) Bruce

Aurora College ? Yellowknife Campus, in partnership with the Northwest Territories Mine Training Society and industry partners, has developed a 6 ? week program on Underground Mining for delivery in Northern communities. The goal of the program is to inform and connect Northern residents to the career potential at existing and future mining operations throughout the Northwest Territories. The program content includes an introduction to the mine life cycle, basic underground mining methods, the use of technology in training via desktop simulators for underground mining equipment, safety in the workplace, and essential skills training (Ready to Work - North) and assessment. Students completing the short program may then choose to continue into a long (12-week) program to be offered at the Yellowknife Campus. This program expands upon the initial introduction and includes modules on NWT geology, environmental studies, underground mining processes and underground mining equipment operation using the larger enclosed cab simulator for a variety of equipment being used at northern mining operations. Success of both programs will depend upon a variety of factors, many of which are outside of the control of the developers of the training modules. These will be investigated throughout the presentation. Connecting northern employers with northern employees is a major concern. It is hoped that through the development and implementation of a program such as this, that the connection can be made and sustained allowing continued employment for the life of northern mining operations.

May 1, 2008

By Parsons. Robert B.

"Starting this year, corporations that conduct business in Ontario face a new tax a corporate minimum tax. This tax is in addition to the myriad of other taxes that make up a corporation's total tax burden including federal and provincial capital 1oXJ!S, payroll tax and sales taxes. Mining companies with gross revenues in excess of $10 million or total assets exceeding $5 million may be liable for this new tax. IntroductionOn December 8, 1993, the Ontario government introduced legislation to implement the corporate minimum tax (CMT promised in its May, 1993 budget. There are very few differences between the final legislation and the budget proposals.The CMT is effective for taxation years commencing after 1993. Subject to certain specific exemptions (detailed below), the tax applies to all corporations liable for Ontario Corporate Income Tax that have either gross revenues in excess of $10 million or total assets in excess of $5 million. These measurements apply to the aggregate gross revenues and total assets for all corporations in an associated group and a corporate partner's share of partnership assets and revenues must be included in the determination.In essence, the CMT is an income tax that is based on financial statement profit instead of an income amount that is determined separately under a statute. Accordingly mining companies (including so called ""junior"" exploration companies), which traditionally sheltered their taxable income by claiming generous exploration and development deductions, could find that they have a CMT liability."

Jan 1, 1994

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By David Rahal, Saul Ortiz, Maria Escobedo

The general trend in the minerals industry is towards the processing of fine grained, disseminated mineral deposits. This has led to an increase in the number of fine/ultra-fine grinding installations using stirred media mills. The challenge is that both the equipment type and the mineralogy of the deposit have an effect on specific energy consumption. Fresnillo PLC recognized this issue and addressed it by providing samples for testing in a laboratory regrind system. The objective of the test program was to determine the specific energy required to achieve a product size of 10 µm (P80). A specific energy plot was generated for both a lead and zinc flotation concentrate. It indicated that 34 kWh/t and 51 kWh/t were required for the two samples (Pb and Zn respectively). This difference highlights the effect of mineralogy on the energy required for fine grinding. The regrind feed and products were submitted to a range of basic mineralogy tests to quantify the mineral differences that could have changed the specific energy requirements. These tests provided general mineralogy, documented optical textures, and provided particle size microscopy. The lead concentrate was found to contain significant amounts of silicates in addition to the dominant sulphide, pyrite. The zinc concentrate was determined to be mostly sphalerite with minor amounts of quartz, chalcopyrite, pyrite and galena. The material testing results illustrate the importance of basic mineralogy studies in conjunction with comminution testing to determine specific energy consumption.

Jan 1, 2016

By L. Voisin, G. Damm

"In order to develop a new pyrometallurgical process for eliminating detrimental arsenic and antimony from the impurity-rich matte produced from copper concentrate, and for treating the occasionally generated speiss in nonferrous smelting processes, the phase relations in the Fe-Cu-S-As-Sb system saturated with carbon at 1473 K were investigated. The distribution of elements between the condensed phases at the miscibility gap, where three equilibrated phases of iron-rich alloy, copper-rich alloy, and matte coexist, were also studied. The investigation was carried out by performing a series of laboratory scale experiments in an electrical furnace at 1473 K, followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Inductively Couple Plasma (ICP), Atomic Absorption Spectroscopy (AAS) and Carbon Infrared Spectrometry (CIS) techniques.The results were compared with previous investigations for the Fe-Cu-S-As-C and Fe-Cu-S-Sb-C systems and discussed on the basis of the molar fraction distribution for both arsenic and antimony in the matte phase at five different matte grades. It is expected that by using this phase separation technique it might be feasible both, the cleaning of a complex copper matte and the elimination of arsenic and iron together with an acceptable amount of antimony into the iron-rich alloy phase, which can be discarded as a harmless and smaller deposit."

Jan 1, 2014

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

By C. Overton, R. W. Nice

"With todays economic trials and tribulations we have all become deeply engaged in costs and cost cutting in our field of mineral processing. Grinding is one of the most expensive unit operations. The cost of grinding media is the most expensive item in grinding costs. Therefore, it is only reasonable to attack the cost-cutting area by trying to reduce the consumption of media. This introduces the field of autogenous or rock-on-rock grinding.Rock-on-rock grinding is not new to us. It has been known for many decades;The South Africans used pebble grinding in the '20's for gold.Mr. B. Crocker was prompted for the same reasons to introduce pebble grinding at Lakeshore Mines in Kirkland Lake during the last war.The Buffalo Anchorite used beach pebbles in grinding prior to the war.Autogenous and semi-autogenous grinding is used quite successfully in the iron ore field. Base metals have their examples in Australia at Caba, in Africa at Komato and in Sweden at Aitik.Recently three mills in British Columbia and one in Arizona started with autogenous mills in their circuits. One was originally conceived to utilize a modified autogenous grind with a crusher in the circuit. All except the same mill had contingency plans for converting to semi-autogenous. All four mills have since converted to the semi-autogenous mode. These are Island Copper, Lornex, and Similkameen in B.C. and Pima Mining in Arizona."

Jan 1, 1975

By Dean McDonald

The Committee Bay Greenstone Belt extends over 300km and is one of the largest unexplored greenstone belts in North America with excellent gold and diamond potential. Committee Bay Resources Limited holds over 550,000 acres of land with prospective geology in the Committee Bay area southwest of Melville Peninsula, Nunavut. Committee Bay is a typical Archean greenstone belt comparable to the Yellowknife, Red Lake, Kirkland Lake and other prolific gold belts. Drilling during 2003 at Committee Bay resulted in: 1) the discovery of high-grade gold-bearing quartz veins with silicification and sulphidation at Three Bluffs, and 2) the continuation of high-grade gold mineralization in the hinge area of the iron formation at Inuk. Gold mineralization at Three Bluffs is identified in iron formation and adjacent sediments and has been traced by drilling for over 700m. The Three Bluffs iron formation is open to depth and along strike where is has been traced on surface for over 6km. In January 2004 Committee Bay and joint venture partner Gold Field?s announced a $7.1 million exploration program for the Committee Bay project in 2004. A total of 8,000m in exploration drilling has been approved for the expansion of the Three Bluffs to the resource stage and drilling of at least five new target areas. Additional mapping, sampling and geophysics will be used to identify new gold targets along the very prospective Committee Bay belt.

May 1, 2004

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

"2.1. General Considerations and Properties2.1.1. IntroductionOur present knowledge of the platinum-group elements (POE) is extensive, the reason being two-fold. The elements have many uses and, moreover, they exhibit extremely varied chemical behaviour, depending on their state of oxidation and chemical environment. The present chapter reviews a selected body of material which is of particular relevance to mineralogy and geochemistry.Comprehensive treatises on the POE include those by Mellor (1956-1957), Gmelin (1938-1957) and Pascal (1958). The inorganic chemistry, particularly coordination chemistry, has been dealt with in works by Griffith (1967), Hartley (1973) and Livingstone (1975), and the analytical chemistry by Walsh and Hausman (1963), Beamish (1966) and Beamish and Van Loon (1972, 1977). Darling (1973) and Savitsky (1978) have reviewed the metallurgical properties and applications of the metals. Goldberg and Helper (1968) have reviewed the thermochemistry and oxidation potentials of POE systems, and Wagman et at. (1969) have also provided selected values of their thermodynamic properties. The geochemistry of the POE has been reviewed by Yushko-Zakharova et at. (1967), Cousins (1973), Cabri (1974), and Naldrett and Duke (1980).Platinum was used briefly as a coinage metal in ImperialRussia. Otherwise, the principal early use for platinum and its alloys was in the fabrication of chemically resistant apparatus. Subsequently, a large part of platinum production was utilized for catalysts in the sulphuric acid and ammonia industries. Platinum has been replaced by vanadium pentoxide in the manufacture of sulphuric acid, but, in recent times, catalytic upgrading of petroleum and emission control systems for automobiles have opened further huge markets for the metal. All of the POE find uses either as reagents or catalysts in the synthesis of organic compounds, e.g., in the Wacker process, which uses palladium chloride to catalyze the production of acetaldehyde from ethylene. There are, of course, a large number of specialized uses for the elements, particularly in alloys, temperature measurement devices, cancer therapy and so on."

Jan 1, 1979

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015