Search Documents

By D. Duffy, V. Papangelakis

"MgCl2 brines present a number of potential advantages for the processing of saprolite ores for nickel production. With a chloride system it is economically requisite to recover hydrochloric acid, which can be performed in a more energy efficient manner by precipitation and subsequent decomposition, as compared with conventional pyrohydrolysis. In addition, concentrated MgCl2 solutions enhance the activity of acid used, allow atmospheric leaching at elevated temperature and inhibit magnesium dissolution, which reduces acid consumption and increases metal selectivity. Leaching and iron control experiments have been conducted in concentrated MgCl2 brines, up to 4.5 m, to determine the most amenable process conditions. INTRODUCTIONChloride metallurgy has received an increasing amount of attention in recent years, especially with respect to the treatment of nickel laterites. Although the limonitic fraction can sometimes be economically treated by High Pressure Acid Leaching (HPAL), acid-consumption problems are encountered with the higher magnesium content of the saprolite fraction. As magnesium does not hydrolyze under HPAL conditions, as iron and aluminum do, any sulphuric acid used to leach magnesium is subsequently neutralized and wasted. In addition, this magnesium must later be disposed of in some fashion, further complicating the process. The most common method used to process saprolite is the Rotary Kiln-Electric Furnace (RKEF). This uses a kiln to dry and preferentially reduce nickel, before sending the calcine to an electric furnace. Although nickel recoveries are high, and the problems of acid consumption are avoided, the capital and energy costs associated with this process are high (de Bakker, 2011).The problems outlined above have led to the investigation of an atmospheric chloride process for the treatment of saprolite ores. The use of a chloride system presents a number of advantages, but also a few limitations. Metal chlorides tend to be very soluble, with a few notable exceptions (silver, mercury and lead), allowing for smaller processing equipment through more concentrated solutions. This solubility also serves to reduce the potential for scale formation. In addition, a hydrochloric acid leach is more aggressive than a comparable sulphuric acid system, and the activity of the hydrogen ion can be augmented by further chloride addition (Peek, 2011). This activity augmentation in concentrated chloride systems, first reported by Jansz, has repeatedly been referenced as a motivating factor behind chloride hydrometallurgy (Jansz, 1983; Harris and Magee, 2003; Harris et al., 2004; Demopoulos et al., 2008; McDonald and Whittington, 2008; Demopoulos, 2011; Peek, 2011; Verhulst and Lakshmanan, 2011). This activity increase allows a similar amount of acid to perform more in a concentrated solution than in a dilute solution, decreasing overall acid requirements. As such, much focus has been placed on leaching in concentrated chloride systems, or brines, using calcium, magnesium or sodium as the cation (McDonald and Whittington, 2008)."

Jan 1, 2012

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Patricia J. Dillon

Established in 1997, Prospectors and Developers Association of Canada Mining Matters (PDACMM) is a registered charitable organization dedicated to providing Earth Science education to grade school students. Through the development and distribution of educational programs and materials, PDACMM informs students of Canada?s geology and mineral resources as well as promoting awareness of the importance of rocks, minerals, metals and the mining industry. PDACMM also co-ordinates with other charitable organizations and government agencies to provide support or to work in tandem with them and reach as many young people as possible. Although PDACMM became a charitable organization in 1997, it actually has its? roots in 1994 when the Grade 7 program Mining Matters/Une Mine de Renseignments was developed to help teachers bring geology and mining into the classroom. Over 2100 of these resource kits were distributed to teachers across Ontario during the period 1995 to 1998. This unit won national recognition when it received the prestigious Partnership Focus award from the Conference Board of Canada for ?promoting science literacy for the world of work?. Due to the phenomenal success of these kits, a Grade 4 kit entitled Deeper and Deeper/Aller au Fond Des Choses was developed in 1998 in response to the opportunity provided by the new Ontario curriculum released at that time. Over 2600 of these kits were distributed throughout Ontario and there is a substantial waiting list of teachers hoping PDACMM will be able to raise enough money for another print run.

May 1, 2002

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By J. Gillies

"Extraction of Gold in Ketone from a suitably prepared sample of sulphide or siliceous ore or concentrate permits a rapid and accurate determination by Atomic Absorption. Mill test products and exploration development samples are acid-treated to effect complete dissolution of silver, copper, zinc, lead, molybdenum and iron present. Interferences in the determination of molybdenum are described. Results by Atomic Absorption are comparable to those afforded by other acceptable methods.INTRODUCTIONDuring recent years much has been written and discussed concerning Atomic Absorption Spectrometry as a technique for determining the concentration of metallic elements. We would, however, recommend a perusal of the paper presented by J. C. Ingles at the annual meeting of Canadian Gold Metallurgists held in Ottawa, January, 1966. The paper was published in the August, 1966, issue of the Canadian Mining Journal, and contains general information on Atomic Absorption.The purpose of our paper is to present certain specific method procedures for the determination of several precious and base metals normally present in Mine, Mill and Smelter products. Of necessity, analytical results should be as accurate as the most suitable available method permits, whether for metallurgical balance, settlement purpose, ore beneficiation programs, or exploration property development. The success of such programs is relative to the accuracy, speed and economics of the analysis. It is obvious, therefore, that in presenting our paper we consider the technique has achieved the desired evaluation."

Jan 1, 1968

By G. R. Yourt

"Generally speaking the usual approach for controlling dust is three-fold:1. Suppress the formation of dust at the source.2. Confine dust that cannot be suppressed.3. Dilute and remove dust that cannot be confined.This discussion will be concentrated on the second approach, namely, confining and disposing of dusty air.Dust BehaviourBefore delving into actual design principles a brief discussion on behaviour of dust should be helpful. For prevention of silicosis only respirable dust, ranging in size from < 0.5 to 5u needs to be controlled. As particles of this size have insignificant mass and momentum they follow air movements very closely. Consequently if contaminated air around dust sources is confined within enclosures and leakages maintained, strongly indraft dust is automatically controlled and capture velocities are of no concern.Dust SourcesAt metal mining operations ore is prepared for wet concentration by crushing it to mostly <3"" in size. This usually involves a jaw crusher, one or two cone crushers, one or more screens and several conveyors. Dust is actually produced only by the crushing action but it is liberated also when numerous fine particles contained in the ore stream are dispersed by surges and vibration at the discharge of the crushers, screens and headpulleys of conveyors. Furthermore, dust is dis¬persed when the slime adhering to the underside of the return portion of belts becomes dry and is rendered airborne by vibration and by cleaning floors especially where the slime has dropped."

Jan 1, 1971

By Robert B. Parsons

"It is quite likely that more than a handful of junior exploration companies will receive some startling news from their accountants this spring when 1989s tax returns are being prepared. These companies could find that, for the first time ever, they will have to write a cheque to the federal government on account of a new federal capital tax which became effective July I, 1989IntroductionMany mining companies which have never had to pay a federal income tax are finding that they indeed have a tax liability for 1989. Non-producing companies, such as junior exploration companies, almost automatically assume that they don&apos;t have to pay any income tax. But, a new tax imposed under the Income Tax Act catches especially the company that has no income.Effective July 1, 1989, a federal capital tax (some call it a corporation minimum tax) is payable by any corporate carrying on business in Canada where the corporation has ""taxable capital"" exceeding $10 million. As a result of the popular use of flow-through shares in recent years, many junior exploration companies are finding that their balance sheets show capital stock over $10 million, and that they are consequently caught by the new tax. Further, some of these companies are finding, to their chagrin, that the tax for 1989 was due on February 28, 1990, and that non-deductible interest is ticking away on unpaid taxes."

Jan 1, 1990

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By Edgar A. Manker

"Today&apos;s market for columbium has only developed in the last two decades, and in this sense it is ""newer"" than molybdenum, vanadium and most other steel alloying elements. In this short period, it has assumed a very important role in steel alloying and in superalloys. From a few hundred thousand pounds of columbium in 1960, consumption has grown to nearly 30 million pounds per year, with a market value approaching two hundred million dollars.To assess the outlook for columbium, we will first consider the historical development of consumption and supply, particularly noting that all of today&apos;s major mines were developed during the last two decades. From current production, we will attempt to reasonably project the future. This future may well include new producers, particularly some producing columbium as a co-product with tantalum.The growth of current applications, and emerging new applications, will be considered with regard to future consumption and in relation to future trends in pricing.IntroductionThe nineteenth century was a busy time for the discovery and naming of new elements. Among those discovered were columbium in 1801 and niobium in 1844. Although it was later shown that columbium and niobium are the same element, the two names are still used today. Niobium has been pronounced the ""official"" name by the International Union of Pure and Applied Chemistry, but columbium is still widely used in commercial practice, and we have chosen to use columbium in this paper."

Jan 1, 1981

By K. H. Singh, J. N. Szuck, J. A. Riddell

"Hydraulic rock drilling equipment has been in use at Falconbridge over the past two years in both production and development situations. This paper deals with the experience gained in the application of hydraulic drilling in the company&apos;s mines and discusses the benefits and problems encountered during their use. The paper primarily focuses on technical, operating, maintenance and economic aspects of the machines, and does not attempt to compare the performances of different machines from the various manufacturers.IntroductionThe Sudbury Operations of Falconbridge Nickel Mines Limited are comprised of five operating mines and two mines under development. All the production comes from underground mines, mostly at depths below 1000 metres. The company, faced with increases in operating costs and difficult mining conditions, has continued to seek solutions with the help of new mining technology.The development of electric-hydraulic drilling machines in Europe had been pursued with great interest and, in 1979, a decision was made to test these machines to prove their technical and economic viability under operating conditions. Since then, a number of electric-hydraulic machines have been evaluated in different situations and currently nine hydraulic machines are being used in the company&apos;s various mines. These machines are comprised of two-boom drilling jumbos for development, one-boom machines for longhole drilling and a large-hole-diameter drilling rig for blasthole drilling. One hydraulic jumbo has also been used in a cut-and-fill stope."

Jan 1, 1982

By B. N. Church, A. R. Pettipas

"The second vertical derivative method of processing aeromagnetic data from low level helicopter surveys yields results correiatable with the known geology and may be utilized to indicate possible targets for future exploration in the Silver Queen and Equity Silver mines areas, near Houston in central British Columbia . The principal zones of alteration associated with mineralization, known from detailed mapping, are further delineated and extended in a way not possible by a cursory examination of the original magnetic data.IntroductionThe second derivative method of processing aeromagnetic data is a long established procedure used to enhance the short wavelength content of the magnetic fields. Some recent exam pies of the use of the second derivative technique have been published by Chandler (p. 385), Sun Yunsheng et al. (p. 424) and Yarger (p. 223) in Hinze, 1985. According to theory, the ""second vertical derivative"" is closely related to the rate of curvature of magnetic (or gravity) fields and is particularly useful in resolving and sharpening local anomalies. The contours on second derivative maps may coincide with important features such as lithological boundaries, faults and mineralized zones.In the Houston area, central British Columbia, aeromagnetic data supplied by local mining companies provide a ready base for analyses. Examples are data sets for the Silver Queen and Equity Silver mines centred 35 km and 34 km south and southeast, respectively, from Houston (Fig. 1), (Cochrane, 1970 and Church, 1985)."

Jan 1, 1990

By S. B. Ballantyne, D. R. Boyle

"Detailed studies have been conducted on the dispersion of uranium in stream waters and sediments around various types of mineralization and hitherto unexplained anomalous areas in the Okanagan Valley and Highland region of south-central British Columbia. These studies were part of the jointly funded and planned Federal-Provincial Uranium Reconnaissance Program of the Geological Survey of Canada and the British Columbia Ministry of Energy, Mines and Petroleum Resources. Statistical analysis of regional data indicates that U in stream waters and sediments varies considerably for different rock types, thus affecting data interpretation. In addition, the data demonstrate a poor correlation between U in stream waters and their associated sediments which can be largely accounted for by variations in climate and water and sediment composition. Regional trends in the distribution of U can be explained in terms of the above secondary factors as well as primary metallization phenomena.Significant correlations between U and F, and U and Mo can be explained by certain magmatic and mineral-forming processes. U shows little correlation with other base metals.The dispersion characteristics of U in the vicinity of Miocene "" basal type "" mineralization ; uraniferous pegmatite terranes, anomalous lineaments in granitic terranes and high-background volcano-sedimentary areas are discussed. Highly anomalous U concentrations in waters and sediments may not always be indicative of mineralization, and guidelines for interpretation require a sound knowledge of the geological and secondary processes operative in the area."

Jan 1, 1980

By P. Au, R. Kearsey, D. Y. Seo, Patnaik. P. C.

Three nickel based superalloys (7.5%Cr+5%Co+2%Mo+1%Ti+5%Al and Ni balance (wt%)) containing different amounts of W and Re were produced in the single crystal (SX) condition utilizing the Bridgman casting process. First, the effect of different levels of Re, and W on chemical microsegregation were investigated by EPMA quantitative analysis, and eutectic phase fraction analysis. Second, in order to investigate the effect of these refractory elements addition on oxidation behaviour, isothermal oxidation testing of the SX nickel based superalloys was conducted at 1000°C for 277 hours under 3 ppm moisture content of air in a thermogravimetric analyzer (TGA). All three SX nickel based superalloys revealed an excellent SX solidification structure with a common primary dendrite arm spacing of -250 µm and a large fraction of ?/?&apos; eutectic located between the secondary dendrite arms. From the average EPMA compositional results, with the exception of Ni, elements such as Cr, Co, Re, Mo, and W all tended to segregate towards the dendrite core during solidification, while Al, Ti, and Ta were present in greater quantity in the last liquid phase to solidify, which resulted in large eutectic ?/? &apos; phases to form within the interdendritic regions. As the nominal level of Re increased, microsegreagation of Re, W, Cr and Mo increased, indicating that Re had a much greater influence on partitioning behavior compared to W. Figure la shows the specific mass gain as a function of exposure time for each alloy. An alloy with 2wt% of W and Re (Alloy B) exhibited less weight gain compared to two other alloys with either higher content of W or Re (Alloy A and C). Microstructural and compositional analyses of oxidized samples were conducted using SEM and EDS. Figure lb shows the typical surface morphologies of the oxidized Alloys A and B. It is evident that more oxide nodules (indicated by arrows in the figure) were presented in Alloy A. It is speculated that the amount of these nodules was responsible for more mass gain in Alloy A compared to the two other alloys. From the examination of the longitudinal section of the oxidized samples as shown in Figure 2, for Alloy A, nodules actually penetrated deep into the material. For Alloy B, however, a relatively uniform and continuous oxide layer was developed and deeply attacked areas were not observed. It was also found that preferential oxidized regions were located at the area between the ?/?&apos; eutectic phase and the dendrite arms where the concentration of refractory elements was relatively high. Therefore, it is plausible that the oxidation kinetics of these alloys is related to the extent of microsegregation.

Jan 1, 2004