Search Documents

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By René Lefebvre

Numerical simulations of the physicochemical processes related to acid rock drainage (ARD) in the Sugar Shack South rock pile of the Questa Mine were performed with the TOUGH AMD simulator. The objectives were to 1) identify the main processes responsible for observed present-day conditions, 2) provide an estimate of gas phase humidity transfer, and 3) give a preliminary indication of the potential impact of closure involving the installation of an alluvial soil cover. Modeling results indicated that the mine rock geometry (thin layers placed along steep mountain slopes) favors the onset of strong thermal air convection. Simulations also indicate that resloping the piles would not significantly reduce convection and oxidation. For simulation purposes, a potential cover with the permeability range of a local alluvium was investigated and found to be of questionable effectiveness since its permeability can exceed the value of 3x10-13 m2 required to prevent thermal air convection and reduce ARD.

Nov 1, 2002

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By A. Montini, M. H. Moys

"A conductivity probe mounted in the shell of the mill has been used to measure the behaviour of the load in the mill as a function of operating variables. It was found that certain properties of the conductivity signal correlate strongly with the per cent solids of the slurry passing through the mill; in particular the angular location ?D of the shoulder of the load is an increasing function of the per cent solids. A method for measuring the viscosity of the pulp discharging from the mill has also been developed. The use of the measurements in mill control is illustrated by simulating various control strategies for open circuit milling. It is shown that the use of ?D allows very tight but imprecise control of the slurry rheology in the mill, while the use of viscosity is subject to severe limitations in speed of response. A cascade control system involving both measurements provides adequate control of slurry rheology within the mill. Applications to closed circuit milling are discussed.IntroductionMultivariable control of milling circuits continues to receive a lot of attention in the literature. Hulbert and co-workers and Niemi, et al. have described the use of Inverse Nyquist Array (INA) techniques while Herbst has recently described the use of Optimal Control. It is significant that in neither of these three projects was any variable associated with the grinding mill itself (e.g. power or properties of the mill discharge) used in the control strategy. Pauw, et al.do, however, use mill power in their multivariable peak-seeking controller for pebble-mill control. Little work has been published on the use of measurements of the properties of the slurry being discharged from grinding mills, in spite of the fact that milling efficiency is known to be strongly affected by slurry rheology».Moys has recently developed a technique for measuring the dynamic behaviour of the load in the grinding mill. This method involves the monitoring of the response of a conductivity probe mounted in the shell of the mill which gives a measurement of the orientation of the load inside the mill. It was found that the load behaviour was strongly influenced by slurry rheology. In this project a technique was also developed for the measurement of the viscosity of the slurry in the mill discharge. It was, thus, decided that it would be worth investigating the use of these measurements in mill control schemes since direct control of the slurry rheology in the mill must inevitably increase the efficiency and productivity of the grinding circuit as a whole.This will be done by using the dynamic responses measured by Moys and Montini to simulate the behaviour of an open circuit ball mill. While the control of open circuit mills is of little interest, this simulation provides a simple but powerful demonstration of the advantage provided by these measurements, advantages which should apply to closed circuit operation of any mill type (including autogenous milling). Investigations into multivariable control of a closed circuit ball mill are currently nearing completion and will be published soon."

Jan 1, 1987

By Roger J. Goodman

"Major industrial restructuring, which started to manifest itself in the mature economies of the Western World and Japan in the 1970s, will accelerate in the 1980s and 1990s. Conventional heavy manufacturing industries will continue to lose ground to lighter processing/assembly operations and the new wave of high technology, information and service sectors. The decline in heavy manufacturing has severely impacted on the steel industries of Western Europe, the U.S.A . and Japan.World trade in metallurgical coal has shifted correspondingly, with declining demand in the mature developed countries being only partially offset by large increases in the steel intensity of the newly-industrialized countries (NICs) of the Far East, Latin America and, to a more limited extent, the Middle East and Africa. These trends will be accentuated in future years with direct implications for the distribution of metallurgical coal trade. This paper discusses, in quantitative terms, such changes in the 1980s and 1990s, and examines the implications for, and impacts on, Canadian metallurgical coal exporters.IntroductionThe twenty-year period from the early 1950 s to the early 1970s was characterized by inexorable growth in consumer demand and industrial expansion in most of the advanced countries of the western world. Long- term forecasting during this period typically used linear extrapolation techniques which , despite their simplicity, invariably ended up predicting future demand and production level s with uncanny accuracy. Times have changed!The last decade has been characterized by a n abysmal failure of our economies to respond to simple long-term, linear growth patterns. We appear to have entered a new world in transition, where we can observe a wave of dying or sunset industries reluctantly being submerged by a wave of emerging or sunrise industries.This paper is aimed a t examining the evidence for long-term industrial restructuring trend s. For want of a better word, these so -called, megatrends are then used to predict future demand level s and spatial distribution of steel development and , hence, metallurgical coal trade. It is tempting to correlate the decline in economic activity in the western world with the first Organization of Petroleum Exporting Countries' (OPEC) crisis of 1973. This crisis was probably no more than the straw that broke the camel's back, as the megatrends and embryo s of major industrial restructuring were already evident. Today these megatrends are merely more apparent and transparent than they were ten years ago.While the concept of industrial restructuring is the new economic buzz word, the process was at work, to a lesser degree even throughout the period of strong economic growth of the post-Second World War boom. Many people still remain convinced that our present-day sluggish economy is just part o f the typical , though rather more prolonged, recessionary cycle. Yet, we have always been part of a dynamic economic system and industry throughout history has been the subject of a continuous process of evolution, restructuring and reconstitution . Now the time is ripe to examine the evidence for such restructuring in order to develop coherent policies of adjustment in this transition from one industrial regime to another."

Jan 1, 1985