Search Documents

By Ferrin Prince

New Gold?s New Afton mine is an 11,000 tonne per day block caving mine, located 8 km west of the city of Kamloops, British Columbia. The reserve is estimated at 52.5Mt with grades of 0.65 g/t Au and 0.93% Cu. Block caving requires a considerable amount of infrastructure development before production can begin. Each excavation had its own challenges, often further complicated by interactions with the caving stresses and fault structures. The main areas of interest were: the production crusher complex, the surface to underground infrastructure, and the footprint interaction with the faults. The ore zone at New Afton is bounded by two very weak fault zones, with large fault affected areas and associated splays. The resulting rock mass rating (RMR) is 35-50, with some areas significantly weaker due to clay infill. These conditions created a unique and decidedly difficult environment in which to develop New Afton?s infrastructure. Despite these difficulties, the mine began production on schedule in July 2012. The main production crusher for the mine is a gyratory crusher that allows for direct truck dumping, with a smaller jaw crusher in series to facilitate the initial development and production. The crusher chamber was redesigned several times to minimize the chamber volume, resulting in a 40% decrease in volume without losing functionality. After drilling and geotechnical testing, the location of the crusher was changed to eliminate the threat of fault affected ground in the area; the entire complex moved a short time before mining began on the chamber. The mining techniques used enabled tight control of the crusher pocket excavation, while also allowing for the timely completion of the chamber. The locations of the surface to underground infrastructure were tightly constrained by geology, surface infrastructure, and an existing open pit. The VR5 raise was drilled and abandoned part way through the reaming process when the drill string became stuck in fault gouge material. It was relocated and successfully completed. The VR7 raise hit a region of poor rock strength and deviated more than 11 m. Poor ground conditions caused a 130m section of the raise walls to fail. An innovative rehabilitation program was undertaken to re-establish the raise for ventilation. A surface to underground slick line was also installed to ease the material movement underground. A layout of the Extraction level was changed from herring bone to straight through drawpoints that resulted in a net reduction of 1.3 km of development. The Apex level was added to aid in the breakage over the major apex pillar and allow for geological mapping. A portion of the caving footprint is located within the footwall fault. The low strength, high clay content, and small joint spacing of the material resulted in blast-hole cut-off and drift deformation. Drift rehabilitation was a key factor in the successful development of the cave footprint. Innovative drilling and loading techniques were used to keep the holes open and to impede movement along the joint structures.

Aug 1, 2013

By R. Anthony Hodge

Who/what is ?community?? What are most communities interested in, what do they care about? What has happened in the past? What is happening today? What is hoped for tomorrow? What are the lessons and keys to success?

May 1, 2006

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By Stephen Mullowney

Outline ? Setting the stage ? Deal activity ? Q1 2013 update ? Key deal sectors ? Deals by geography ? Outlook for 2013 Key Observations 2012 ? Major retreat in M&A activity ? Glencore-Xstrata deal dwarfs all other deals ? Gold & copper dominate deal activity

May 1, 2013

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By J. Scalise

The paper covers a wide range of topics relative to filtration for continuous cast copper and aluminum. Subjects include system concepts, filtration concepts, system components, filter types, filter media selection, caster water filtration, coolant disposal, and recommended materials of construction.

Jan 1, 2007

Delivering Our Products On any given day in North America, 80 kilometers of rail cars are engaged in moving our product. Global Customer Base Our business accounts for more than 30% of all bulk goods moved through the Port of Vancouver

May 1, 2006

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By Lawrence Devon Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analysed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a ""bare bones"" base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.INTRODUCTIONOften, the first time that all of the technical and economic data for a mineral project comes together in one place is when the economic evaluation is developed. This typically happens when work on the project has progressed to a sufficient level of detail that the effort to produce a year-by-year cash flow is justified, usually at the pre-feasibility or feasibility study stage. The data involved will include:• production; tonnes waste and ore mined, ore grade, mining recovery, metallurgical recovery, metal sold• revenue; metal price, smelting & refining charges, marketing costs• operating Costs; mining, milling, administration, fees, royalties• capital Costs; exploration, development, construction, indirect costs (engineering, management), contingencies, start-up, inventories, working capital, replacement and sustaining capital, closure costs• taxes and royalties• exclusions; depreciation (this is not a cash item), sunk costs (only costs going forward)."

Jan 1, 2003

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By W. E. Halle, G. J. S. Govett

"The Institute of Applied Geology, Manila, Philippines, is jointly sponsored by the University of the Philippines, the Philippines Bureau of Mines and the United Nations Development Programme (Special Fund). It provides, in its fourth year of operation, an interesting example of international cooperation in mineral development. Objectives include: (1) the training of mining engineers in modern techniques of mineral exploration; (2) assisting government and industry in discovering new ore deposits; and (3) providing the basis for the establishment of an economically oriented graduate school of geology at the University, the first of its kind in the country. Training of engineers requires roughly one full year, which is divided between academic study and actual field practice. Lecture and laboratory instruction include courses at university level designed specifically to up-grade those aspects of the geological sciences that are required by mining engineers now qualifying as mineral exploration engineers-economic geology, applied geochemistry, geo-physical exploration, petrology and structural geology. The field training involves direct participation in actual mineral exploration projects arranged with the co-operation of the Bureau of Mines and private interests engaged in mineral development and production. The system works well in practice, and the Institute staff and trainees were responsible for outlining new evidence of economic mineralization. It is also apparent from the application of the exploration methods available to the project -geological mapping, air photo interpretation, magnetic, electric, electromagnetic, self potential and gravity surveying as well as geochemical prospecting -that, under the humid, tropical, mountainous conditions in which the practical program was conducted, air-supported geochemical prospecting with attendant reconnaissance geological mapping affords the most economical and effective approach to mineral exploration for at least some of the deposits characteristic of the region."

Jan 1, 1968

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By A. C. de Araujo, M. G. Barbosa, R. Martino, S. Gaydardzhiev

The Iron Quadrangle district is a world-class iron ore mining district in the region of Belo Horizonte, capital of Minas Gerais state, in Brazil. Many mining companies have been mining high-grade hematite ores for decades throughout the region. The mines reserves often include itabirite ores which are available in high volumes, but have lower iron grades than hematite ores and require elaborated mineral processing to meet the requirements of downstream steelmaking. Itabirite ores have acquired importance, with the depletion of high-grade hematite reserves due to their intensive mining. The objective of this paper is to propose a geometallurgical model for the processing of itabirite ores from an Iron Quadrangle deposit, which will allow predicting the behaviour of ores throughout the deposit, according to their local variations. An initial step consists in characterizing representative samples of the different ores to acquire mineralogical and textural data. Then, itabirite ores of known characteristics are processed with different techniques, in order to extract the trends and key parameters upon which the geometallurgical model is developed. At first, the model takes into account the particle size distribution and its shift during mining and screening, as well as the chemistry and mineralogy of the material. Then, using the previously identified key parameters such as iron recovery, the model predicts the composition of the processing products. Finally, this data is used to model the mineralogy and mass recovery of the products. The geometallurgical model is of great importance, as it is able to model the processing of any sampled ore throughout the deposit. The incorporation of the results in a mining block model will assist mine planning and opens new opportunities for an optimized mining schedule.

Jan 1, 2016

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952