Search Documents

By James D. Hall

THE Dome ore-bodies are more or less isolated and are mined. by shrinkage stoping. An interwoven system of veins is mined at Hollinger '.1.nd requires close filling. Deep mining is the problem at McIntyre. Dome ore contains a large amount of free gold, which is recovered on blankets. An all-cyanide flow-sheet is \lSed in the Hollinger mill. Flotation concentration is an important feature of McIntyre mill operation. Therefore, these three mines afford an unusual opportunity to compare gold mining and milling methods. The purpose of this paper is to describe the conditions existing at the Dome, Hollinger, and McIntyre mines and to outline the mining and milling practice at each property. Figures 3, 4, 5, and 7 are reproduced from the Canadian Mining ]011rna/, September, 1935 (Young, A. W., Mining at Hollinger), and Figures 8 to 11 from the Engineering and Mining Journal, November, 1933 (Keeley, D. E., Development and Mining at McIntyre). The photographs (Figures 6, 12, and 13) are by The Canadian Government Motion Picture Bureau. Diagrams of the several mill flow-sheets, which formed a part of the original paper, are not reproduced here. They will be found in Dorr's Cyanidation and Concentration of Gold and Silver Ores.

Jan 1, 1938

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By W. J. Bennett

"I AM very happy to have this opportunity of speaking to the Montreal Branch of the Canadian Institute of Mining and Metallurgy.I have selected as the subject of my remarks transportation in that area which is at present our only source of uranium -Northwest Canada. Considering the widespread interest in atomic energy, the end-product of uranium, it may be wondered why I have not chosen to speak of a more spectacular aspect of the development. I hope it will be evident from what I have to say that transportation plays a very dominant role in our effort to maintain a continuing supply from Eldorado's producing property at Port Radium on Great Bear lake and from its coming producer at Beaver lodge Lake in Northwest Saskatchewan. Moreover, transportation has such a bearing on the entire mineral development of the Northwest that it cannot help but be of concern to an organization of this kind. Finally, the transportation problem, of which I shall try to tell you something, is quite unique and the story of its solution or partial solution is, I believe, an interesting one.Transportation experience on this continent indicates that the cheapest method of moving freight is still by water -with •rail, highway, and air transportation following, and in that order •of economic significance. Excluding rail transportation, since the area has as yet no railway lines, this order also applies in the Northwest. I shall direct my remarks to the two kinds of transportation which serve our uranium producers -water and air."

Jan 1, 1952

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By A. W. Lovett

"THE last two years have been years of recession or, perhaps, years of marking time, depending upon whether the observer is a pessimist or an optimist. There has been a slackening in the industrial tempo that has been reflected in many ways in the national economy. As one of the chief barometers of economic health, the consumption and supply of energy reflect this slowing up.These same two years have also seen significant changes in the relation between the sources of energy. In periods of declining demand, it has happened in the past that coal, as the basic or residual source of energy, has shown the effects to a greater extent than the other energies. In these two years, however, in addition to this usual effect, there has been the acceleration in the Joss of market to diesels in the railway consumption category and the continuing decline in domestic consumption. The story of these years is presented in the statistical tables that form the foundation of this paper. Statistics, particularly in the form of tables, are rather dry and are sometimes difficult to follow but the overall developments are illustrated by graphs which present a more striking picture."

Jan 1, 1959

By C. H. Bertoni, A. Vachon

The Corner bay copper deposit is the first significan discovery on the south limb of the Dore Lake Complex, located at the eastern end of the Detour Lake-Chibougamau greenstone belt, Quebec. The deposit was discovered in March, 1981, after 26 years of intermittent work in the area. Mineralization is found in a shear zone cut ting rocks ranging in composition, from gabbroic anorthosites to anorthositic gabbros which have been intensely altered and deformed by at least two tectonometamorphic events. Both the copper-bearing shear zone and its host rocks are cut by a large NE-striking gabbro dyke. Most of the known mineralization is found east of the dyke, but two deep exploration holes have shown that the down dip extension is present to the west of the dyke. The mineralized shear varies from one to 15 metres in width, strikes around 010° and dips from 70° to 80° to the west, and has been tested for a length of 700 metres. The wall rocks are usually chloritized and silicified. Mineralization is characterized by chalcopyrite, pyrite, molybdenite, magnetite, and sphalerite occurring mainly as the matrix to quartz-carbonate breccias in the "main" shear zone. The predominant sulphides are pyrite and chalcopyri te as crystals or fragments. The brecciated mineralized shear shows evidence that there was at least one remobilization of the shear and it is suggested that copper-bearing fluids invaded the shear during its remobilization. The exact timing and source of mineralization are not known. Up to February 1984, 38 holes had been drilled to outline indicated reserves to a depth of 450 m of 1,5 million tonnes grading approximately 4% copper, 0.34 gm, gold and 13.71 gm silver per tonne. It is believed that there is considerable reserve potential in the block west of the gab bro dyke, the down dip extension of the main zone.

Jan 1, 1984

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By D. P. R. Smyth

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By Aidan Giblett, Michael McGlynn, Peter Radziszewski

"On the basis that 99% of the energy input into a mill is converted into heat, it is possible to estimate the amount of energy captured in the slurry, the amount that is lost to the environment as well as the possible means to reduce such losses. As a result it becomes possible to estimate the potential amount of energy that can be captured by technologies such as thermoelectric generators or even Sterling engines. Furthermore, it has been suggested that the energy recovery potential dry grinding circuit could be as high as twice that of wet grinding circuits.In this paper, the energy recovery potential of dry grinding will be explored by examining the case of the Newmont Carlin mine dry grinding circuit. The paper will open with a review of the energy recovery potential of a few wet grinding applications followed by a description of the dry grinding circuit and a definition of the control volume around that circuit. A thermodynamic model will be used to estimate the circuit discharge temperature and an estimate of any losses as well as provide an estimate of the potential impact of different means to reduce energy losses. The paper will close with a discussion of the assumptions used in model development."

Jan 1, 2016

By I. M. Marshall

SOME years ago the writer had the opportunity to plumb a number of mine-shafts, each of which presented various conditions and difficulties. This afforded the chance to compare several methods of shaft plumbing in the light of ease and rapidity. This comparison led to the development of an adaption of the Weisbach, or approximate alignment, method, to three wires in a single shaft. Professor Weisbach, some time prior to 1850, introduced his method of shaft plumbing by triangulation on but two wires, and was the first to show that a triangle of very narrow shape is the best for this purpose. THE WEISBACH METHOD The two-wire method, using a Weisbach triangle, is described in several .English text-books on mine surveying and is used frequently in various parts of the world, but in Canada it is almost unknown. The writer has described an example of this two-wire method (1), but a brief resumé here may clarify the explanation of its application to three wires. In this two-wire method, instead of endeavouring accurately to align the instrument with the wires, it is set only in approximate alignment, and the small angle formed at the instrument is measured. This is expressed graphically in Figure l, where C represents the position of the instrument and A and B the positions of the wires. The sides of the triangle are measured as well as the angle ACB, and the angles at B and A are found by applying the Sine Rule or the formula

Jan 1, 1938

By W. J. Gibson

"This paper will provide a general assessment of the differences in construction and industrial labour relations. From this outline will come a detailed examination of labour relations in the construction industry and then specifically as related to the construction of mining projects, with emphasis on projects in isolated areas. Development of manpower forecasts, manpower availability, wage escalation formats, working rules, training and recruitment programs, and safety - as related to construction labour relations in the mining industry - are topics which will be dealt with."

Jan 1, 1972

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By W. S. Fyfe

Gold is mobilized and precipitated in a wide variety of environments ranging from those of weathering and biological phenomena, to pluton emplacement to deep metamorph ism . But it appear that pervas ive leaching of large rock volumes fo llowed by the focussed di charge of typically low salin ity flu ids is frequently involved. There are great gaps in our knowledge, particula rly with re pect to gold in very high temperature fl uids generated at near Moho depths. But uch flu id may play an important part in Archaean pluton associated lode gold deposits whe re ultra high temperature fluids, rich in C02-CO-COS, may be associated with magma underplating and crustal assi mil ation processes (sag subduction) associated with very den e ult ramafic magma . Other environment with great potential include those of major thru t fau lt and strike slip fa ult s where large quant ities of fluids are mobilized .

Jan 1, 1986

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015