Search Documents

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By T. Patching

"A GLANCE BACK AT what has happened in the past is often a useful guide to the future, although it should be used mainly to provide a sense of direction rather than a map that must be followed. As a preamble to discussing some of the questions posed by the organizing committee it may be appropriate to briefly review the distribution and careers of the graduates of our Department since the first degree in mining engineering was awarded in 1916. An attempt has been made to keep a record of the locations and careers of the Department's 540 graduates in mining and metallurgical engineering. Almost all of those who graduated before 1930 have now retired, but a very large proportion held positions as senior executives prior to retirement. A major proportion of those who graduated before 1950 are now in what might be considered senior management positions. Those who have 10 to 20 years of experience are generally in work of senior engineering responsibility or in supervisory or junior management ranks, while those who graduated in the last ten years appear to be generally in staff engineering or junior supervisory positions. This classification is admittedly imprecise because it is difficult to determine from a job description whether duties should be considered of an engineering or management nature - a distinction between the two terms is often over-emphasized. Nevertheless, the trend from technical engineering to management responsibilities with seniority and years of experience is clear in the careers that we have been able to follow."

Jan 1, 1972

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By John B. Hodgeson

AMMONIA is an essential constituent in the production of the ammonium-sulphate and ammonium-phosohate soil fertilizers manufactured by the Consolidated Mining and Smelting Company of Canada, Limited. The fertilizer plant, built in 1930 at Warfield, near Trail, provides a means of utilizing the large amount of sulphuric acid produced from the sulphur dioxide which is removed from the smelter smoke. The plant has an avail-able source of cheap power which makes the production of fertilizer economically possible. The fundamental operations involved in the production of ammonia at the Warfield plant are, first, the manufacture of hydrogen by the electrolytic dissociation of water; next, the recovery of nitrogen by the fractional distillation of liquid air; and finally, the combination of hydrogen and nitrogen in proper proportions and under suitable conditions to form ammonia.

Jan 1, 1938

By John Loop, W. A. Gibbins, Donald D. Hogarth

"Introduction Background The Frobisher voyages of 1577 and 1578 were organized by the Cathay Company for the express purpose of finding and mining gold ore. Since publication of the Baffm expedition of Charles Francis Hallill, the location of Kodlunarn or Countess of Warwick Island, the headquarters of Frobisher's third (1578) voyage, and focal point of the largest Arctic voyage of all time, has been known to the world. Through Hall we also know the location of the Countess of Warwick Mine on Kodlunarn Island. However, the exact locations of the other mines are not known. Of the ""ore"" we know little. Pieces of the original ""black stone"", once as large as ""a half-penny loaf' have now disappeared altogether. Specimens collected at random from the repository of shipments in England and from loose rock on Kodlunarn Island were termed, respectively, ""hornblende pyroxenite"" and ""amphibolite"" and from a locale about 200 yards from Kodlunarn as (hornblende) ""pyroxenite""121. However, it is uncertain whether these specimens are representative of Kodlunarn or of the other mines, although Blackadar131 notes that, in the northern trench of Kodlunarn, biotite gneiss contains lenses and bands of amphibolite. The ""gold"" itself is even less well defined. It has long been accepted that gold was virtually absent in Frobisher's ore. The ""gold"" has been termed pyrite, biotite and both biotite and pyrite together. Even t h e word "" marquesset"" , which appears and reappears in contemporary descriptions, is nebulous and is defined as ""a stone participating in the nature of some metal, yet in so small quantity, that the metal cannot be melted from it"" (0.E.D., definition of 1616)."

Jan 1, 1999

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

By J. B. Mawdsley

From the view point of the mining engineer, the square-set method of stoping as practised at Butte, Montana, is one ?of the outstanding features of well conducted mining operations in that camp. The following information was obtained in the course of two months underground work in the Granite Mountain mine, during the summer of 1920, which is one of the properties of the North Butte Mining Company, situated on the well known Speculator vein. Most of the information was derived from personal observation and from discussions with various miners and with members of the staff. Geology The copper mining area of the Butte district is some two miles long by one and a half miles wide, a mineralized area in a great batholith of monzonite granite, locally known as the Boulder batholith. This extensive body of granite is traversed by several series of mineralized fault-fissures which differ in strike but generally dip steeply. Geologists agree that following the formation of the fissures, alkaline solutions ascended and decomposed the felspathic portions of the granite in the immediate vicinity of the fissure walls, and that these alkaline solutions were followed by cupiferous solutions which filled the fissures and replaced the granite next to the walls. A zone of oxidized ore, varying in thickness from 10 to 400 feet, overlies a sulphide zone containing chalcocite, enargite, bornite and chalcopyrite, with a small amount of quartz gangue. The veins are from 3 to 100 feet in width and contain, on the average, 3 per cent of copper, 2 ounces of silver, and 15 cents in gold per ton.

Jan 1, 1925

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By A. B. Rossetti

"THE MISSION TO Offshore Scotland was in my opinion a very worthwhile venture, as it indicated the scope of the offshore oil and gas business and how we might exploit it to the fullest here in Nova Scotia - if our offshore fields eventually become producing fields. The writer was able to attend a considerable number of lectures and as a result gained some valuable know-how on the engineering design, financing and operation of the North Sea oil industry. There are many new fields of technology that had to be developed to overcome the North Sea's hostile environment and a great deal of the same technology will have to be developed to win oil and gas from our continental shelf. The visit left me with several impressions, which in the main are:(1) The high order of investment required to develop offshore oil. The investment ranges from 10 to 20 times that required for a similar output on land. Each barrel of oil costs on the average of about $2,- 500 per barrel per day.(2) Because of the high investments required, before the first oil is produced the field must be brought into production at the earliest possible date and initial lead time from decision to production is less than four years. In the British Petroleum field, working at a depth of 450 feet will require an investment of $900,000,000 to develop a production of 400,000 bbl per day. (3) The size and complexity of equipment required is beyond anything ever imagined. Problems which must be overcome are such factors as water depth, wind velocities, wave height, wave period, long periods of darkness, low temperatures, distance from land, and fog."

Jan 1, 1973

By L. C. Graton

Introduction The Porcupine district of northern Ontario has yielded over $300,000,000 in gold during its twenty-three years of mining operations. It thus ranks among the foremost gold producing areas of the world. Of this $300,000,000 already produced from the District, the Hollinger mine has furnished over 60 per cent and stands as one of the greatest gold mines of all time. In 1929, the Hollinger Directors decided to supplement the current geological and development work by an intensive investigation of the geology of the mine. This special study, begun in June of that year, was completed in October, 1932. An account of the geology of the mine in a degree of detail commensurate with the intensity of the study is in course of preparation. But the widespread interest manifested at the present day in gold occurrence generally, in Canadian gold deposits, and in the specific results of the investigation at Hollinger, appears to justify the immediate presentation of a highly abridged summary of our principal findings, insofar as they relate to the more general and scientific phases of the geological situation. Those conclusions having direct bearing on operating and exploratory policy are not dealt with here. The present preliminary paper, therefore, records chiefly the conclusions reached, with little incorporation of supporting argument or evidence. While intended to give a reasonably balanced perspective of Hollinger geology, the condensed presentation naturally emphasizes those views which are not in complete accord with accounts hitherto published regarding this district.

Jan 1, 1933

By Peter Wells, Gordon Marrs, Dominic Fragomeni, Warren Holmes, Daryl Macnamara

"LocationThe Strathcona mill ofFalconbridge Limited is located in Onaping, Ontario, 50 km northwest of Sudbury.GeneralOre from the Falconbridge mines in the Sudbury Basin (Strathcona, Fraser, Onaping, Craig and Thayer Lindsley mines) is processed through the Strathcona mill with 8500 t of nickel ore and 1500 t of copper ore being treated daily. Current capacity is -3 Mt of ore at 1.8% Ni, 1.9% Cu combined grade. Custom feeds are also processed. The valuable minerals in the ore are pentlandite (FeNi)9S8, chalcopyrite (CuFeS2) with some cubanite (CuFe2S3) and very minor nickel sulphides/ arsenides. Cobalt is present mainly in solid solution in pentlandite. There are small but economically important concentrations of precious metals including platinum, palladium gold, and silver. The common non-sulphide gangue minerals are feldspar, quartz, mica, talc, and chlorite while pyrrhotite (Fe7S8) is the major gangue sulphide. The pyrrhotite contains between 0.6% and 1.2% nickel in solid solution and additional nickel as exsolved pentlandite in micron sized blebs. The nickel and copper ores are batch-crushed in a two stage dry crushing plant and then ground in separate circuits. Concentration by flotation and magnetic separation produces a nickel concentrate assaying approximately 16% nickel plus copper and a copper concentrate assaying 30% copper and 0.4% nickel. The nickel concentrate is trucked as a slurry to the Falconbridge smelter while the copper concentrate is trucked as filter cake to the Kidd Division of Falcon bridge"

Jan 1, 2000

By H. T. Kennedy, D. L. Flock

"The project described in this pa-per was undertaken to provide a more thorough understanding of the effect of contamination by drilling fluids on the electrical properties of porous systems. The basic work per-formed was filtration tests on both consolidated and unconsolidated sands and the determination of their resistivity profiles with the aid of screen-type electrodes spaced at convenient intervals along the core.Four drilling fluids were selected, ranging in resistivity from 447.0 ohm-cm. to •5.76 ohm-cm. The permeability of three unconsolidated and four consolidated cores, on which resistivity measurements were made, varied from 1,257 md. to 4,560 md. Five additional cores with permeabilities as low as 49 md. were tested to investigate the effect of permeability on the depth of invasion of drilling fluids.The effect of drilling fluid invasion on resistivity profiles was determined on cores containing brine only, and on those containing 80 to 90 per cent oil and 20 to 10 per cent brine. The study included measurements of (a) clay content of different sections of the core, (b) saturation of the invaded fluids and oil in different parts of the core, and ( c) changes in resistivity as a result of gravitational re-distribution of fluids and diffusion of electrolytes.The data showed that the resistivity of an invaded core is, as was expected, controlled by the resistivity of the filtrate, the resistivity of residual core water, the resistivity of the clay particles, and the amount and distribution of the filtrate, clays, residual oil, and brine. In most cases there was a significant increase in resistivity owing to the presence of clay solids which had invaded the core. The change in resistivity, as a result of the diffusion of salts, was substantial after a period of five hours. There is evidence in some cases that the residual oil and core water saturations of the unconsolidated cores, after substantial invasion, are very low, indicating almost complete displacement by invading fluid."

Jan 1, 1959

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006