Search Documents

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

Overview of Presentation ?About MiHR ?Human Resources Challenges in the Minerals and Metals Industry ?Getting the Facts -Sector Study Project ?Key Findings ?Recommendations ?Conclusions ?MiHR?srole

May 1, 2006

By Z. D. Hora

has been no commercial production of either perlite or pumice in British Columbia. Several promising occurrences are known to exist but their development has been delayed due to difficult access and / or remote locations. The Empire Valley perlite deposit is located 120 km east of Clinton. The deposit appears to be a flat-lying volcanic flow 50 to 70 m thick that is part of an Eocene rhyolite and dacite volcanic assemblage. The Francois Lake perlite deposit occurs on the north shore of Francois Lake where perlite is part of a rhyolitic volcanic sequence. The exposure of perlite is about 13 m thick and is considered to be Eocene or Oligocene in age. The Uncha Lake perlite deposit is located about 5 km south Industrial Minerals in Canada of Uncha Lake. Perlite appears to be intercalated with porphyritic rhyolite flows that are comparable to those at Francois Lake. Showings are widespread but poorly exposed and thicknesses are unknown. The Mount Meager pumice deposit is located in the Lillooet River valley at the base of Plinth Mountain. Coarse pumice agglomerate forms a large talus slope that is undercut by the river. Unsorted, angular fragments up to 50 cm in diameter are intermixed with up to 30 per cent of sand and silt-sized particles. The exposed zone is about 200 m long and 50 m high; it is being considered as a source of lightweight aggregate.

Jan 1, 1984

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By A. Zarei-Hanzaki, S. M. Fatemi-Varzaneh, M. Haghshenas

The microstructure in modified semi-solid ALTHIX (A356) alloy consists of aAl phase with Al/Si eutectic structure. Silicon phase in eutectic structure is coral like with fine fibers. The lack of good ductility in this alloy is related to the presence of silicon fibers. Accordingly many investigations have been recently conducted to modify the Si morphology through Thermomechanical processing on this alloy. In the present work an ALTHIX (A356) alloy was deformed at 450°C, 500°C and 540°C through different strain rates. Consequently the silicon fibers were broken into small particles. The results indicated that the Si particles may coarsen according to Ostwald ripening mechanism at 540°C deformed by rate of0.0005 sec-1 & 0.0001 sec-1-

Jan 1, 2006

By Wencheng Gao

An attractive way to beneficiate magnesium chloride and aluminum chloride is to prepare Mg-Al spinel, an excellent refractory material. Mg4Al2(OH)14?3H2O, the precursor of spinel, can be prepared using a co-precipitate method from aqueous MgCl2-AlCl3 solutions. The co-precipitation process of magnesium-aluminum from acidified chloride solutions by using NaOH or NH4OH as base neutralization agent was studied. Co-precipitation was conducted from different mixed solutions ? at initial CAl=0.0625M and Mg/Al molar ratio from 0.5 to 10, the temperature range from 30 to 90 °C. The effect of other parameters, including base type, method of base addition, base addition rate, aging time, background electrolyte and concentration were also investigated. The co-precipitation process was monitored by potentionmetric(pH) measurements. The experimental pH curves were characterized by two platforms separated by a steep jump in pH at Mg/Al molar ratio 0.5~6. The first platform was centered at about a pH of 3.8 and the pH of second platform was varied with different conditions. When the Mg/Al molar ratio was up to 6~10, the first platform in pH was almost disappeared. Furthermore, the shapes of pH curves were also affected by base type, base addition rate and method of base addition. Experimental results showed that the first platform in pH was connected with Al precipitation, and the second platform was involved with Mg. The final co-precipitates were characterized by XRD, TGA-DTA, particle size analysis, SEM and TEM. We found both Mg/Al molar ratio and temperature proved to be the key parameters controlling the formation of Mg4Al2(OH)14?3H2O phase. At solution Mg/Al ratio=0.5~4, the main precipitate phase was Bayerite (Al(OH)3) admixed with Mg4Al2(OH)14?3H2O; at Mg/Al ratio=4~6, the main phase was Mg4Al2(OH)14?3H2O admixed with some Mg(OH)2; while from Mg/Al ratio=6~10, the systems were mixtures of Mg(OH)2 and Mg4Al2(OH)14?3H2O.

Oct 1, 2011

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

By J. H. Hodgson

"Those of us who have been concerned with the problem of geophysical exploration in southwestern Ontario have followed the development of the Poulter method with much interest. I have much appreciated the opportunity of reading an advance copy of Dr. Poulter's clear exposition and of preparing the following brief remarks on the probable applicability of the method to the Palaeozoic area of southwestern Ontario.During the years 1944 to 1946, the Ontario Department of Mines, in co-operation with the Union Gas Company and the Dominion Natural Gas Company, operated an experimental party in the hope of establishing a seismic technique appropriate to the •area. The results were completely negative. During two summers' field work, no reflections whatever were obtained except in one area near Windsor. It is the •purpose of these remarks to inquire whether Dr. Poulter's techniques might yield favourable results.It was the conclusion of the report on our work that two principal causes contributed to the failure of the method. In the first place, the geological column possesses few elastic discontinuities and those that exist appear to have low reflection coefficients. In the second place, the area is drift-covered in general. This drift complicates the situation by absorbing seismic energy and by giving rise to groups of complicating refracted phases which obscure the entire interesting section of the record. The situation is further complicated by the high reflection velocities and the relative shortness of the Palaeozoic section, these factors combining to bring in a reflection from the basement in about half a second."

Jan 1, 1950

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By M. J. Michaud, M. J. Lavigne

"Abstract - North American Palladium Ltd. operates its Lac des Iles open pit palladium mine 85 km north of the city of Thunder Bay, Ontario. The Roby Zone deposit occurs within the mafic/ultramafic Lac des Iles Intrusive Complex (LDI-IC), which was created by multiple pulses of magma of varying composition within several closely spaced chambers. Chaotic lithological distribution, the presence of magmatic breccias, and the rarity of rhythmic layering suggest a dynamic intrusive environment with disruptive magma pulses. As of December 31, 2001, measured and indicated resources for the 950 m long by 815 m wide Roby Zone deposit totalled 159 Mt grading 1.55 g/t Pd, 0.17 g/t Pt, 0.12 g/t Au, 0.05% Cu, and 0.05% Ni at a palladium cut-off grade of 0.7 g/t. The Roby Zone contains an additional 73 Mt of inferred resources at similar grades.The Roby Zone is dominated by varitextured gabbro containing pipes and pods of breccia, and large blocks (~60 m across) of varying lithology. Mineralization at Lac des Iles occurs as: (1) a PGEand base metal-rich magmatic matrix of breccia (breccia ore); (2) mineralized dikes or sills (gabbronorite in North Roby ore); (3) lower-grade mineralization in varitextured units that are host to the distinctive breccia ore and envelope the North Roby ore; and (4) high-grade mineralization associated with strong silicate alteration exemplified by high-grade ore.The close spatial association of the mineralized breccias with both varitextured units and silicate alteration leads to an interpretation that the energetic magma that created breccia was charged with a dissolved fluid, and that this deuteric fluid exsolved at high temperatures to migrate through crystal mush, enhancing crystallization along its pathways, resulting in variable grain size. This transformation occurred at high temperature and produced sulfide-poor, varitextured gabbro-hosted mineralization exemplified by some of the mineralization in the North Roby Zone, and also found throughout the Roby Zone. The association of hydrous silicate alteration with mineralization can be explained by continuing fluid migration during cooling and continued metal transport. Résumé - North American Palladium Ltd. opère la mine à ciel ouvert de Lac des Iles située à 85 km au nord de Thunder Bay, Ontario. Le gisement Roby Zone est encaissé dans le complexe mafique/ultramafique de Lac des Iles (LDI-IC), lequel représente une intrusion polyphasée créée par plusieurs pulses magmatiques de différente composition à l’intérieur de chambres magmatiques fermés. La distribution chaotique des lithologies, la présence de brèches magmatiques, et la quasi-absence de litage rythmique suggèrent un environnement magmatique dynamique perturbé par l’introduction de nouveau magma. Au 31 décembre 2001, les ressources mesurées et indiquées s’élevaient à 159 millions de tonnes titrant 1,55 g/t Pd, 0,17 g/t Pt, 0,12 g/t Au, 0,05% Cu, et 0,05% Ni, pour une teneur de coupure de 0,7 g/t Pd. De plus, la Roby Zone contient 73 millions de tonnes de ressources inférées à une teneur similaire.La Roby Zone est principalement encaissée dans un gabbro de texture hétérogène (varitextured) caractérisé par des cheminées et des lentilles de brèches et des énormes blocs (environ 60 m de diamètre) de plusieurs lithologies. Au Lac des Iles, la minéralisation en EGP et en métaux de base se retrouve dans la matrice magmatique de brèches (breccia ore), dans des dykes ou des sills minéralisés (gabbronorite dans la zone North Roby ore), comme minerai de basse teneur encaissant le minerai de brèche (breccia ore) et enveloppant la zone North Roby. Du minerai de haute teneur est également associé avec une forte altération en silicates dans la zone high-grade ore.L’étroite association spatiale entre les brèches minéralisées et les unités de texture variée (varitextured) et l’altération en silicate suggère que le magma énergique qui a causé la bréchification était chargé de fluides. Ces fluides deutérique"

Jan 1, 2001

By Peter Clevenstine

Minnesota Iron Ore Trifecta 1. World Demand 2. Industry Consolidation 3. Competitive Advantages

May 1, 2011

By G. R. MANSON

The Brisco Barite Mine lies 70 km south-southeast of Golden, British Columbia. Barile mineralization occurs in a northstriking brecciation zone within Ordovician-Silurian Beaver/ oot dolomites and quartzites. Brecciation was caused by faulting related to the Mount Forster-Steamboat Fault. The main barite vein occupies a fault zone and is up to 12 m wide and over 250 m long. It is light grey to white, fine grained and compact; BaSO4 content is 9/. 70 per cent. Production started in 1945 and has continued to the present. Barile originally was removed from an open pit; later, an adit, begun in 1957, reached more than 240 m along the vein, 15 m below the pit floor. Today ore is hoisted from a decline resting some 37 m below the pit floor.

Jan 1, 1984

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group ('B' Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d'Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By Michel Gauthier, Jacque Trottier

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum. Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This third paper (the first was by Fyffe, et al., in Vol. 83, No. 938, the second is in this issue) in the series presents an overview of the tectonic setting and geochemistry of base metal deposits in the Eastern Townships of Quebec.ABSTRACTIt is well known that the classification system of volcanogenic massive sulphides (VMS) is based upon their metal content. This metal content, the result of hydrothermal solutions circulating within strata underlying the deposits, is generally thought to be related directly to two parameters: (1) the nature of the underlying stratigraphic sequence; and (2) the physico-chemical conditions that existed at the time of the hydrothermal event. Furthermore, these two parameters are, in turn, related to the tectonic setting. One must bear in mind that these parameters are diachronous and evolve with time. These factors are considered in our analysis of the major VMS deposits of the southeastern Quebec Appalachians. This analysis will describe the time and environment of formation of these deposits and integrate them into an evolving paleotectonic model.VMS deposits in the southeastern Quebec Appalachians formed during three distinct metallogenic episodes. During the first episode, which involved early closing of the Iapetus Ocean and associated destruction of oceanic crust by subduction processes(Early Ordovician?), cupriferous VMS deposits hosted by pillowed, mafic (boninitic) lava flows were formed in immature island-arc systems (""Cyprus-type"", e.g. Huntingdon deposit).In the second episode, which also occurred during the closure of Iapetus but at a later stage (Early to Middle Ordovician), mature island-arcs formed and hosted polymetallic VMS deposits (""Kuroko-type"", e.g. Eustis deposit).Finally, during culmination of the Taconic and/or Acadian orogenies (Middle Ordovician and/or Devonian), transtensional basins, associated with tholeitic to transitional mafic volcanism began to develop. Major sedimentation occurred contemporaneous with volcanism, and within this framework polymetallic VMS deposits were formed (""Besshi-type"", e.g. the Memphremagog deposit).Although incomplete, the proposed paleotectonic model represents the sequence of the tectonic settings that prevailed during the formation of the VMS deposits of the southeastern Quebec Appalachians."

Jan 1, 1991

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954