Search Documents

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By Eric D. Monrad

Supply chain simulation modeling is taking on a more prominent role in mining project planning and decision making. Transportation costs for the supply chain can form a significant component of the overall cost to provide product to the end customer. In recent years, computing power has increased, simulation software has advanced, and simulation specialists have become even better equipped to provide sophisticated analysis and recommendations. This has led to a virtuous cycle of owners expecting and supporting data-driven analytics, which drives further advancement. This paper discusses developments in supply chain planning and two case studies from recent simulation modeling analyses.

May 1, 2013

By R. H. Nafziger

A novel process has been developed for preparing directly workable steel ingots from prereduced iron ore pellets by a two-stage process. The pellets are continuously charged into an electric arc furnace, where molten metal is separated from the gangue. The molten metal flows out of this furnace through a hollow nonconsumable graphite electrode immersed in a molten flux in an electroslag furnace. The molten metal solidifies on a continuously withdrawing base plate to form the ingot. A variety of standard carbon and alloy steel ingots . free of porosity , were produced using suitable decarburizers and ferroalloy additions. Some advantages of the two-stage process include: (a) consumable electrode fabrication is eliminated; (b ) no expensive deoxidizers are required; (c ) the uncontaminated electros lap flux can be reused; (d) energy consumption averages 25% less than in a conventional electric arc - electroslag operation ; and (e) the operation is continuous.

Jan 1, 1977

By I. R. Muirhead, A. L. Craven

The trend in mining thermal coal is only to mine coal with the lowest sulphur content. In many coal seams, bands of coal with high sulphur content are often present, generally occurring either at the roof or floor level. Methods of selective mining are, therefore, necessary to recover only the low sulphur coal. This paper examines the methods currently in use in mines and the alternative methods that are able or have potential to offer control of shearers and continuous miners where greater thicknesses of coal have to be left in the roof and floor. These alternative methods rely on such characteristics as neutron gamma radiation; electromagnetic waves; vibration; infrared; infrared; optical; pick force; X-ray fluorescence; conductivity; gyroscopes and laser systems.

Jan 1, 2000

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By Greg Gosson

"Early efforts to develop formal reporting systems to quantify and classify mineral deposits date back over 100 years. (e.g. Hoover 1909: “Proved, Probable, Prospective Ore”). This was at first driven by mine operators’ need for reliable estimates of what their mines could produce. Disruption of transportation routes by world wars prompted western governments to recognize the need for assessments of strategic sources of metals and minerals that could support domestic industry during times of crisis. Categories were created to quantify mineral potential which were additional to those of mine reserves. Terms such as hypothetical and undiscovered resources entered the lexicon. Capital markets serving the mining industry were traumatized during the latter part of the 20th century by undisciplined and fraudulent disclosure by exploration companies of mineral deposit potential. Government securities regulators pressed for the development of credible reporting codes (e.g. SEC Industry Guide 7: 1981; JORC 1989; SAMREC 1994, CIM 2000). Representative organizations from the major western mining countries generally agreed that there should only be three categories of mineral resources (measured, indicated, and inferred) and two categories of mineral reserves (proven and probable). This was formalized in 1997 with the “Denver Accord”. Acceptance of the standard terminology may have been the easy part, because the challenge for the 21st century is to get general industry acceptance and agreement of the principles behind the definitions of each category. There has been noticeable movement towards this objective in the last few years. This is reflected in part in the updated reporting codes by JORC 2004, CIM 2005; SAMREC 2007; SME 2007; and PERC 2008, and the development of the CRIRSCO International Reporting Template 2007."

Jan 1, 2003

"SART technology is a useful tool for improving the economics of gold recovery from certain types of complex gold ores. SART liberates cyanide consumed by base metals such as copper, zinc and nickel, and enables the newly freed cyanide to be recycled to precious metals leaching while producing high-grade base metal sulphide concentrates for sale. The benefits of SART include the reduction in cyanide consumption, avoidance of cyanide destruction costs, minimization of risks of environmental non-compliance due to residues of cyanide destruction reporting to mine effluents, and generation of extra revenue from the sale of base metal concentrates. Concerns with SART typically include uncertainties around capital and operating costs and proper integration of SART into the overall metallurgical flowsheet. This paper presents two case studies addressing these concerns. The first involves actual costs of the full scale SART integrated into a gold heap leach operation and treating up to 500 m3/hr of leach solution at a mine in Mexico. The second involves field pilot testing and a preliminary cost estimate for integrating SART into a silver mine in Peru using Merrill Crowe.INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes in traditional gold extraction metallurgical flowsheets. One of the tools available to the industry to help deal with interferences of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle. Although SART is a commercially available technology, it is still relatively new to the industry. Fewer than ten (10) full scale plants have been constructed in the past couple of decades. Some of these SART plants are small, most are located at remote sites, and the majority have not operated on a continuous basis. This has resulted in a general lack of information in the industry about the true costs, operability and metallurgical performance of SART. BQE Water has been involved in the design, construction, commissioning and operation of large scale SART plants in Mexico, Turkey and Chile and has conducted field testing programs as part of the technical assessment of SART integration into various metallurgical circuits. Having built and operated numerous plants utilizing selective sulphide precipitation of heavy metals, BQE Water has gained unique insight into the design and control of the sulphidization stage of SART to minimize costs and ensure high efficiency in cyanide recovery."

Jan 1, 2017

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972

By P. H. Tolcher

Canada, as the Free World's largest mine producer of zinc and the third largest mine producer of lead, has a vital interest in the future growth in demand for these metals. This paper traces the development of lead and zinc consumption in the last two decades, both on a total-Free-World basis and by major market areas. How Canada, as a major mine producer, has shared in this growth is also indicated. In addition, future consumption for both metals in the current decade of the 1970's is fore-cast. The demand these projections will make on Free World mines, particularly on Canadian mines, is examined. Some of the opportunities and challenges the Canadian mining industry will likely face during this period are also dealt with.

Jan 1, 1971

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By H. A. Steane

THIS PAPER describes the re-grind section in the 2,000-ton per day, lead-zinc flotation mill of Canadian Exploration Limited, near Salmo, B.C. There are two re-grind units in operation, one in the lead circuit, and one in the zinc circuit. In each unit, the rougher concentrate is re-ground ahead of the cleaning circuit. These re-grind units have made valuable improvements in the concentrate grade, and with no loss in recovery by over-grinding galena or sphalerite. Since the initial installation of this re-grind section, the plant throughput has been increased gradually from 1,600 tons to 2,000 tons per twenty-four hours, and, as shown by the screen analysis of mill tailing, a coarser overall grind has been accepted, from 55 per cent to 45 per ?cent minus 200 mesh. There has been no increase in grinding capacity, but two mills have been taken from the main grinding circuit and used for the re-grind circuit.

Jan 1, 1958

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

By A. Blackmore, A. Lamoureux, J. Woloshyn

This paper provides an overview of recent applications of Computational Fluid Dynamics (CFD) to combustion related fugitive emissions problems. The aim is to illustrate the capabilities and discuss the present limitations in this field. Examples include design of retrofitted NOx reduction technology in a kiln and in a boiler, and the prediction of pollutants such as SO2 and metallurgical dust emanating from a copper flash smelting furnace. It is demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause problems and testing solutions, and for concurrently assessing emissions reduction and process impact. In addition, the value of CFD for demonstrating due diligence for regulatory compliance is discussed.

Jan 1, 2015

By Michael J. Lawrence

"The VALMIN Code was developed and formally adopted by The Australasian Institute of Mining and Metallurgy (AusIMM) in 1995 and a revision was issued in 1998. The VALMIN Code applies to all relevant reports under the Australian Corporations Law, including submissions to the Australian Stock Exchange (ASX) and the Australian Securities and Investments Commission (ASIC).The VALMIN Code and Guidelines sets standards for the preparation and commissioning of independent assessment and/or valuation reports on mineral and petroleum assets or mineral and petroleum securities.It is mandatory for AusllvI:M's members to follow this Code in these relevant circumstances and failure to do so will result in serious sanction of the member by the Ausllvllvfs Ethics Committee. Public support for the use of this Code has been given by regulators (ASX/ASIC) and market participants ( eg major accountancy firms). It is also endorsed as a guide to general best practice in project assessment and valuation.This paper will discuss how the VALMIN Code has worked in practice over the past few years. It will also examine areas where the Code could be improved and how it could form the basis of a new Canadian Code for mineral property valuation."

Jan 1, 2003