Search Documents

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By S. A. Kenzap

Risk & Uncertainty ? Uncertainty about a situation can often indicate risk, which is the possibility of loss, damage, or any other undesirable event. Most people desire low risk, which would translate to a high probability of success, profit, or some form of gain. Risk = Likelihood x Consequence Risk is the possibility of loss, damage, or any other undesirable event.

Oct 1, 2010

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By Karl J. C. Harries

"10.1. INTRODUCTIONDefinitions are a necessary part of every agreement. Their purposes are to assist the reader in reading and understanding an agreement and to attempt to avert potential confusion and, therefore, disputes. In some circumstances, they may be critical in deciding a dispute. As they are often substantive, they should not be treated lightly.It is far easier and less confusing for a reader to read “the Company” or “the Recipient” than to be faced with “the party of the First Part”, or to see the “Jones Property” than “that part of the property hereinbefore described in paragraph 1.01 hereof”. It is also advisable not to use “-ee” and “- or”, as in payee and payor.One thing must always be remembered: once a word has been defined in an agreement, it will always have the defined meaning unless the contrary is clearly indicated or is required to make sense of a provision.2 It can be confusing for a reader if commonly used words are defined in other than ordinary terms. Unique words that will stand out in the text are more likely to be recognized as having special meaning. It is also good practice to identify defined terms by capitalizing them in the text of the agreement. Boldfacing of definitions is also sometimes used for this purpose but, as boldfacing is not easily identified in handwritten revisions, it can be missed in the press of negotiations, especially when several typists are involved. Lack of consistency in identifying defined terms is not a fatal mistake, but it can create confusion, especially if the reader is new to the agreement or is reading it in a highly technical manner, such as when there is a dispute.If definitions used in the main text also apply to a schedule, they need not be included in both. Omitting them from the schedule makes the agreement look shorter, which to some people is a benefit. If definitions are not repeated, make certain that the schedule clearly indicates that words defined in the main text have the same defined meanings in the schedule3 and are clearly identified as defined words. In considering whether or not to repeat in a royalty schedule definitions appearing in the agreement proper, think of definitions as an aid and a reminder to the reader. Repeating them will help a reader, if only by saving the nuisance of remembering where to find them in the main text and constantly turning to it. All the definitions needed to read the schedule will be right there, so that the schedule is a self-contained document. Just make certain that, if you do repeat a definition, you repeat it in identical terms. If you have to change any defined term to make it fit the royalty provisions, use a different word or phrase as the defined term to warn the reader that he is dealing with a different concept.4"

Jan 1, 2003

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By Mike Robotham

Drum hoists in the 21st century have the same fundamental objective as their earliest 19th century counterpart. And yet a lot has changed in the design of the hoist from those early days of underground mining. These changes are driven by the need for greater productivity and reliability at ever increasing depths without compromising the all important safety demanded by the industry today. This paper reflects on how these changes have influenced design of a modern hoist Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2013

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By N. Melnyk

"FOREWORDThis paper provides a unique description of a method devised for mining a very thick steeply dipping seam of soft gassy coal which was prone to spontaneous combustion. The editors con¬sider that the information in this paper should be important to those who may have to consider mining such seams again at some time in the future and therefore believe that the paper warrants reprinting in the present volume. The author was ask¬ed to review the paper and to add any additional relevant in¬formation. He provided the accompanying footnote, only a month before his death on April 22, 1982.IntroductionIn the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels. and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated.The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not lend themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition the present operations in this particular' seam are being carried on at a level below the former workings, introducing new problems, not encountered on the upper level.Coal will, without question, long continue to be an impor¬tant factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion."

Jan 1, 1985

By J. R. Giegerich

Purpose It is the purpose of this paper to describe the application of underground conveyor systems to the transportation of ore in the Sullivan mine of The Consolidated Mining and Smelting Company of "Canada, Limited, at Kimberley, British Columbia. General Applications Conveying has been recognized as a means of underground transportation for a great number of years but only during the past fifteen to twenty years has there been any extended application of the method to underground metal-mine operations. Coal miners became conveyor conscious before metal miners. Probably one reason for this is the fact that there are more flat coal seams than flat orebodies. A second reason is that coal is light and is a less abrasive material than most metallic ores. The vast improvements made in belt construction during the past few years, together with improvements in mechanical conveyor equipment, have gone a long way in making this form of transportation attractive to the metal miner. In new mines being opened today, or in major extensions to older mines, the possibilities of conveyor transportation should receive serious consideration. There may not be any widespread application of the belt conveyor as a replacement for the conventional hoisting and locomotive haulage. Where there is an application, tl1e saving in cost can be appreciable and many operating ad-vantages gained because of ease in operation.

Jan 1, 1951

By R. F. Sharpe

THE Bullion mine, in the famous Cariboo district of British Columbia, is situated on the left bank of the South fork of the Quesnel river, approximately three miles below the outlet of Quesnel lake. A good road leads 63 miles northeast to the property from Williams lake, the railhead on the Pacific Great Eastern railway. The mine may also be reached over good roads from Vancouver via the Fraser canyon, Ashcroft, Clinton, and the 150-mile house, a total distance of 407 miles. In the early days of placer mining on the South fork of the Quesnel, several rich bars were found. The 'pay' on one of these at the mouth of Dancing Bill gulch was followed up the gulch by a Chinese company, who proved to be the discoverers of the present Bullion mine. This Chinese company commenced working in 1884, in what was then referred to as the China pit. Although working under very primitive conditions, it is reported that, during the ten years they operated the property, they recovered in excess of $900,000 in gold. This somewhat large recovery was due to a local concentration, the result of Dancing Bill creek having meandered down that portion of the channel and washed off the overburden. In 1894, a syndicate composed largely of the Canadian Pacific Railway directorate of that time, with J. B. Hobson as their field manager, acquired the property, as the apparent magnitude of the operation was too great for the resources of the Chinese company. Mr. Hobson, during the first ten years of his regime, developed the mine into a large-scale hydraulic operation, and during that period, from 1894 to 1905, recovered approximately $1,234,000 in gold. In 1906, the property was sold to the Guggenheim Exploration Company, who retained Mr. Hobson as Manager and embarked on an extensive programme to bring in additional water. This project was never completed, however, work being suddenly abandoned in 1907 and the mine closed down. Shortly afterwards, the property was purchased by a small operator on what is believed to have been largely borrowed capital. This venture resulted in no production, but in much litigation, which eventually reached the Privy Council in 1920.

Jan 1, 1939

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By A. G. Ballachey

Introduction This paper will describe the mining plant and underground operations at Quemont. Details of geology and milling are beyond its scope. Papers on these subjects will be prepared and presented separately. A detailed account of the exploration and development, 1944 to 1947, has been given by W. L. Brown (1). Location The mining concessions of Quemont Mining Corporation, Limited, are in Rouyn township, Rouyn-Noranda county, northwestern Quebec. These concessions total about 640 acres in area. They lie within the limits of the City of Noranda, contiguous to, and directly north of, the Horne mine of Noranda Mines, Limited. A large area in the southern part of the property is covered by the north arm of Osisko lake. Production The present operating rate is about 2,100 tons per day. Three flotation concentrates are produced: copper, containing a large proportion of the gold and silver in the ore; zinc; and pyrite, which carries an appreciable additional proportion of gold. The copper and zinc concentrates are shipped to smelters as produced. The pyrite concentrate is cyanided to recover additional gold, after which it is filtered, dried, and shipped for the manufacture of sulphuric acid. The principal revenue metals are copper, gold, and zinc. Silver and pyrite are important by-products.

Jan 1, 1952

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By I. E. Wahn, E. A. Boutin

"The Manibridge Mill is unique in its treatment of relatively high grade nickel-copper ore because in the mill design are included one 10' diam. x 10' Maxwell cell, and three 12' diam. x 12' tank cells. These large cells are used as rougher-scavenger cells. Three 8' diam. x 8' tank cells as well are used for cleaning and recleaning of the tank cell concentrate.Flexibility of flow is the main criterion in the tank cell circuit. Targets from these cells are a high grade nickel-copper product with a minimum of talcose gangue.The operation of the tank cells has been encouraging and they have performed well with both low and high grade heads, yielding a high grade concentrate product.Manibridge Tank CellsDescription:The tank cells at Manibridge consist of one 10' x 10' Maxwell cell, three 12' x 12' tank cells, and three 8' x 8' tank cells. The four large cells are currently being used as rougher scavenger cells. The three small cells are used as cleaner cells.Both sets of tank cells consist of Denver steel tank and Super Agitator Mechanisms with steel beam super-structures. The agitator mechanism has a totally enclosed ball bearing spindle housing with a cold rolled steel shaft, and a stanclard standpipe with adjustable collar.The air rings for the tanks were fabricated by Nelson Machinery. Both large and small cells have injection rings with equally spaced air holes in the bottom centre line of the ring.Air is supplied to the tank cells by a Dresser Clark low pressure air blower.The following is a table of pertinent data on the tank cells:"

Jan 1, 1974