Search Documents

By Muhammad Tawalbeh

The calculated temperature history of a single particle of MgCl2 hydrates when it came in contact with fused salt electrolyte at 650 °C was determined using the measured heat transfer coefficient for the molten salt bath at 650 °C. The calculations revealed that the entire interior of the particle reached the temperature required for the formation of MgOHCI from hydrated MgCl2 in less than 2 seconds. This was much less than the time required for dissolution of the prills as observed in experiments. It is very likely that the formation of MgOHCI during prill dehydration and dissolution is a result of hydrolysis in the interior of the prills.

Jan 1, 2004

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By A. D. Akerman, D. D. Young, G. R. Baiden

The development and maintenance of underground roadways are increasingly important aspects of the modern mining process. With the trend toward automation and track-less mining, roadbeds capable of with standing increased wheel loading have proven necessary to maintain high vehicle speed and reduced maintenance costs. Concrete has been used successfully on some roadways in order to obtain the required characteristics. However, this solution usually involves unacceptable expense. The objective of the Road Router project was to create a drift floor profiling machine capable of cutting a smooth surface out of the existing rock floor of development drifts and ramps. This surface would provide a durable, high strength, low rolling resistance roadbed that would allow for reduced operating cycle times and lower maintenance costs of scoops and haulage trucks. The Road Router has the potential to offer an alternative to concrete with substantial cost savings.

Jan 1, 1997

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By P. T. O'Kane

The PLATSOL® process, initially developed for the treatment of the NorthMet Cu/Ni/PGM concentrate, has seen over the recent years its applicability extended to include numerous other Cu/Ni concentrates of the same type, as well as other precious metals-containing feedstocks. However, several concentrates were found refractory to the typical PLATSOL® conditions, more particularly so the platinum. Attempts to extend those conditions, such as higher temperatures (250°C), longer retention time, increased oxidation conditions, higher chloride additions, were not successful. Detailed mineralogical investigation of those PLATSOL® leach residues indicated the main refractory mineral to be cooperite (PtS). Further metallurgical investigations showed that a thermal pre-treatment of the concentrate effectively unlocked the refractory platinum minerals for the subsequent leach. Temperatures between 400 and 750°C were tested, with the optimum being found around 650°C. The kinetics of the pre-treatment process were fast, and one hour at temperature proved sufficient. Under those conditions, PLATSOL® extractions were re-established around 95% for both platinum and palladium. From a mineralogical examination of the calcine, it was shown that the effect of the pre-treatment was to transform the cooperite and other refractory sulphides into metallic platinum and alloys, amenable to the PLATSOL®. The implications of the pre¬treatment step for the processing of PGM concentrates arc briefly discussed.

Jan 1, 2004

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By Steven Chung

Decision Network Modelling in a mining operation represents a complex process environment that is inherently more variable than a processing plant or factory. The uncertain availability of loading locations, haulage paths, loading and hauling equipment, along with inconsistent operator behaviour, cause a relatively large number of upset events that must be recognized, communicated and dealt with by the appropriate management authority. Traditional process maps that represent a deterministic model of the mining process can quickly break down in the face of such a volatile environment. An alternate modelling strategy, composed of decision networks, focuses on the interactions between goal-oriented entities and their environment, allowing system integrators to explicitly determine the information to be exchanged while providing feedback mechanisms that improve system flexibility and decision quality. This ensures a consistent framework for incrementally increasing system automation.

May 1, 2010

By W. Curlook

"A review is presented of a growing number of imperatives, some self-imposed, some imposed by society, which the mining and metals industry faces in carrying out its business. These imperatives bear on all activities from the exploration phase, through engineering, design, plant construction and operation, to decommissioning.IntroductionThe mining and metals industry must learn to cope with, i.e. manage, a growing number of imperatives. Some of these, such as the need for responsible stewardship of natural resources, the requirement to respect laws and regulations, the need to provide for safe and healthy workplaces, and the need to provide appropriate returns to investors of capital , have been with the industry for a long time (fable I). But the industry now faces additional imperatives that are growing in number and in importance (fable 2):• There is the growing concern about the impact of operations, not only on the workplace environment and the external environment, but also on the need to monitor not only the chemical concentrations in various effluents but to also monitor the effects of such emissions on the environment; i.e. there is a growing concern about the ""net"" consequences of operations.• There is the need for on-going improvement in productivity and safety to compete and survive in a global economy. The global business environment has become paramount.• There is the imperative to failsafe all designs, equipment and operational procedures, and having done that to provide for containment of unavoidable spills, and to have ready and in place systems for emergency response.• There is the need, indeed the imperative, to involve all employees in various quality improvement programs.• There is the imperative to face up to ""virtual elimination/zero emissions""; and• One must have waste management plans in place to cope with the need to reduce, reuse, and recycle; and• There is the need for decommissioning plans for all operations, for the restoration of business habitats to their original states (or better). Indeed, one must engage in the decommissioning exercise from day one, i.e. right from the time of design and commissioning."

Jan 1, 1992

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By Kati Tschöpe

Cathode wear has become an increasing challenge in the aluminum industry due to the use of more graphitized materials. Today, there exist no standard laboratory methods for measuring cathode wear where different commercial materials can be ranked. The typical average wear rate in an electrolysis cell is quite small. The aim of this work was to design a test method where the wear could be accelerated compared to industrial cells. It was focused on polarized tests where the cathode is exposed to electrolyte, which gives higher aluminium carbide solubility. The cathode materials were characterized by microscopy and image analysis.

Jan 1, 2011

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale (MD/FE) method has been used to study dislocation generation and plastic deformation during a nanoindentation process which is physically associated with the generation of heat within the specimen and as a consequence with a temperature rise. Two different techniques are applied to study the temperature effect on the nanoindention process. In the first technique, a global Nose-Hoover thermostat is applied to the entire atomistic region to keep temperature constant during simulation (finite temperature approach). In the second method, the thermostat is applied only on a damping region along the MD/FE interface. Both techniques are able to effectively and efficiently absorb high frequency reflected waves from atomistic/continuum interface. The temperature profile of the atomistic region beneath the indenter is reported and discussed at four different initial substrate temperatures for both techniques. The loaddisplacement (load/unload) curves for different temperature-controlling techniques are compared and discussed. The nucleation and propagation of dislocations in the atomistic region are investigated for both techniques. Correlations between the observed features in the load-displacement curves with the motion and pile-up of dislocations are reported as a function of temperature.

Jan 1, 2006

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009

By J. F. Perreault, J. Paraszczak

"The profitability of an underground mine depends to a great extent on the production cost.Random equipment failures and their consequences have significant influence on the total operating cost of a mining system. Having this in mind, a reliability study has been initiated for loadhaul- dump machines in an underground mine. The main purpose of this study is to identify the critical machine subsystems, determine their failure pattern and help work out an effective maintenance strategy. In the first part of this study, the failure data of diesel powered LHDs, gathered during an I8-month period have been analyzed. For the purpose of the analysis, the machines have been treated as systems comprising seven subsystems connected in series. The most critical subsystems, i.e. electrical and hydraulic, were further investigated, and analyzed by graphical and analytical methods. Different failure distribution models were applied and discussed. Basic Defmitions and ConceptsIn order to avoid confusion, several terms used in this paper are defined below, as compiled by O'Connor (1991). The acronymsBS and MIL-STD stand respectively for: British Standard and US Military Standard.Failure: the termination of the ability of an item to perform a required function (after BS 4778).Time Between Failures (TBF): the length of time between two consecutive failures.Observed Mean Time Between Failures (MTBF): For a stated period in the life of an item, the mean value of the length of time between consecutive failures computed as a ratio of the cumulative observed time to the number of failures under stated conditions (after BS 4778).Maintenance, Corrective: The actions performed, as a result of failure, to restore an item to a specified condition (after MIL-STD-721 B).Maintenance, Preventive: The actions performed in attempt to retain an item in a specified condition by providing systematic inspection, detection and prevention of incipient failure (after MIL-STD-721B)."

Jan 1, 1994