Search Documents

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930

By M. Vallée

"RÉSUMÉDurant les 10 dernières années, les améliorations dans le contrôle des limites des sautages et les arpentages après l’exploitation ont fourni des informations préalables et post facto sur les limites minières réalisées par rapport à la planification, plus particulièrement pour les grands chantiers exploités par les méthodes chambres vides et sous-niveaux. Cependant, peu de recherches ont été faites pour améliorer la délimitation du minerai, l’estimation des ressources et des réserves, les études de faisabilité et la récupération minière dans d’autres types de gisements. Il faudra d’abord expliciter les impacts des lacunes, en quantité et en qualité, de l’information géologique et de l’échantillonnage sur le rendement de l’extraction. Il faudra également remplacer la notion de « dilution générale » par celles de « dilution » et de « perte de minerai ». Les impacts des lacunes observées sur l’exploitation des gisements d’or filoniens sont démontrés par une simulation basée sur des résultats d’études antérieures à la mine Thompson d’Inco, des impacts financiers de densités d’information moindre et par des analyses des valeurs actualisées nettes (VAN) de deux cas types.Deux gisements similaires, de 3 m et 6 m de largeur et exploités par chambres vides sont étudiés, en prenant pour cas de base la délimitation sur maille de 7,5 m (25 pi.) et en étudiant les impacts des limites moins précises supportées par une maille de 15 m (50 pi.), en assumant que ces imprécisions moyennes de +/- 0,62 m se transforment soit en surestimation (dilution), soit en sous-estimation (pertes de minerai).Les impacts d’information moins précise ont été beaucoup plus forts sur le gisement plus étroit : autant la dilution que les pertes de métal ont diminué les VAN du gisement de 3 m de 39,27 % et 45,41 % respectivement, tandis que les VAN du gisement de 6 m ont été diminuées que de 12,84 % et 11,55 %.Ces impacts des valeurs actualisées nettes diminuées justifient et exigent des efforts plus systématiques pour s’assurer que les travaux de mise en valeur et les études de faisabilité soient réalisés de façon requise pour optimiser l’exploitation et offrir aux investisseurs des rendements compétitifs par rapport à ceux des autres secteurs industriels. ABSTRACTDuring the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits.However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses have not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently are poorly documented, the use of these terms is reviewed.Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco’s Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delineation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study.The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit"

Jan 1, 2005

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By E. Latorre, T. S. Golosinski

ABSTRACT; his paper proposes new methodology to define the pit limits that yield the maximum net present value (NPV) for a deposit, under a given economic scenario and for a given discount rate. The method uses an algorithm that combines dynamic programming and heuristics. It was tested for evaluating deposits with different sizes and various grade distributions. For the discount rate of zero, the results confirm that the economic pit limits are the same as that defined using Lerchs Grossman method. However, when discount rates higher than zero are used, the pit limits differ, yielding a higher NPV.

Jan 1, 2011

By Rufus L. Chaney

A new technology is available to the Ni mining and remediation community to “phytomine” Ni from mineralized or contaminated soils using rare plants which hyperaccumulate Ni to over 1% of shoot dry matter. Research has identified useful plant species, and even bred improved cultivars of Alyssum murale and Alyssum corsicum for commercial phytomining in temperate regions. All agronomic practices (fertilization, soil amendments, planting and harvest methods) needed for economic phytomining were identified to attain high yields and high Ni concentration in the biomass. In tropical regions, other species are available such as Phyllanthus which accumulate over 1% Ni in dry shoots. These species are perennial so they regrow after annual cutting to harvest biomass. Expiration of our patents on the technology opens the opportunity for other organizations which control Ni rich natural soils or contaminated soils requiring remediation to commercialize the technologies. Inexpensive methods to remediate/revitalize Ni contaminated phytotoxic soils using agronomic approaches have also been developed and demonstrated at Port Colborne, Ontario, but adoption is delayed until formal agreements with government are completed. These new simple remediation and profitable phytomining technologies can obtain Ni from soils which contain Ni well below levels considered economic for current mining technologies, and the plants biopurify the Ni so it is easy to recover Ni metal from plant ash by pyrometallurgical or hydrometallurgical technologies. Although increasing pH decreases the solubility of Ni in all soils, raising pH increases Ni accumulation by Alyssum species. Hence usual chemical extraction methods for phytoavailable soil metals such as the DTPA- or NH4-OAc-extraction cannot predict Ni accumulation by Alyssum species.

Jan 1, 2016

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of 'internal microstrains'. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By B. L. Moreau

Certain gas wells tend to form hydrates in the production tubing. This paper outlines a method developed and used by the Author's company to overcome the problem. The injection of glycol to control hydrates results in sufficient dehydration to allow the gas to be trans-ported through a field-gathering system b a treatment plant. Sub-surface injection of glycol also offers a method of introducing corrosion inhibitors into the gas stream. The major operating difficulties have been overcome and the system is now in use in the northeastern part of British Columbia.

Jan 1, 1958

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By C. M. Anson

This paper describes the progresses used in the manufacture of steel wheel-centres, tyres and axles at the works of the Commonwealth Steel Products Co., Newcastle, N.S.W., Australia. The plant is adjacent to the Northern railway and consists of three main buildings, namely: the foundry, the forging and rolling shop, and the machine shop. The foundry contains a 6-ton Heroult electric furnace, together with all necessary mechanical appliances for moulding. Reheating furnaces, steam hammers and tyre rolling mill are installed in the forging shop. The machine shop contains lathes, boring machines, and hydraulic presses. Until this plant commenced operations all wheels used in Australia were imported, previ.ous to the war, from England and Germany, and latterly from England only. Besides being of great benefit to the country in that there is now a domestic source of supply of these articles, there is also the advantage of retaining the home market; and in addition, a small portion of the population are now engaged in highly technical occupations requiring a great degree of skill. The plant began to operate in October 1919, and by 1921 was in a fair way to meet the domestic demand for those articles of railroad equipment which it manufactures.

Jan 1, 1925

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012