Search Documents

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Xian Jian Guo, Lei Li, Hua Wang

The distribution and behavior of As, Pb and Zn elements in the copper smelting process were investigated using thermodynamics. The differences between thermodynamics evaluation and practical smelting processes were analyzed. The main factors affecting the distribution of the elements are oxygen enrichment in blowing, copper matte grade and smelting temperature. In general, the distribution ratio of As, Pb and Zn to off gas increases with the smelting temperature and decreases with oxygen enrichment in blowing. Meanwhile, their distributions in matte decreases and that in slag increases with the increase of copper matte grade. There is some gap in distributions between thermodynamics evaluation and practical smelting processes. INTRODUCTION The copper concentrates usually contain a number of minor elements, the control of which in copper smelting processes is often a key to the quality of the anode copper produced and may also have a bearing on the overall economics of the process (Yang et al., 2017). Knowledge of the thermodynamic properties of the minor elements in slag is very important in the control of the slagging reactions (Takeda Y, Ishiwata & Yazawa, 2007). In addition, the environmental contamination caused by the minor elements associated with copper-bearing ores, such as As, Pb and Zn, has become more and more important (Wang, 2004). Arsenic, lead and antimony, which are all carcinogenic metalloid elements, are usually contained in iron-rich wastes, and theirs emissions are considered to be one of the foremost environmental concerns (Wang, 2004). It is important to elucidate the elements distribution of them in the reducing-matte smelting process. The distributions of As, Pb and Zn elements in the copper smelting process are dependent on many factors, including the temperature, raw material composition, reduction atmosphere, concentration level, and slag chemistry etc. (Chen L Z, Xu X, 2016). Generally, these minor elements mainly distribute in phases of gas, copper matte and slag in the smelting process (Shu, Wang, & Qu, 2016). The arsenic exists mainly in the form of sulfo-arsenides in the copper concentrate, and it will decompose and be oxidized in the smelting process (Chen & Lu, 2016). Part of the products, including AsS, AsO, As2 and As2O3, evaporates into the gaseous state, and some other part enters into slag phase in the form of As2O3 and As2O5 (Wang, Guo, & Tian, 2017). Meanwhile, the As2O3 in the slag phase can also be reduced to metallic As and combine with Cu, S, Fe forming Cu3As2, As2S3 and Fe3As2, and then enter into copper matte. During the copper smelting process, about 50% of zinc enters into slag phase in the form of ZnO and 45% exists in the copper matte in the form of ZnS. Little volatizes into the gas phase. Most lead exists in forms of PbS and PbO in the copper concentrate, and it is mainly distributed in copper matte in the smelting process (Zheng & Lin, 2015).

Jan 1, 2019

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978

By Oleg G. Tovmachenko

We have studied optical properties of fluorescent nanoparticles. These particles consist of a metal (gold/silver) core, an empty and a dye labelled silica shells. The different dye molecules with moderate quantum yields (about 0.3) has been used. Almost all of types of nanoparticles show fluorescence enhancement. This enhancement is strongly dependent on the degree of the overlap between the surface plasmon band of the metal and the absorption/emission band of the dye molecules. The results are interpreted in terms of competition between local field enhancement and quenching of fluorescence by the metal surface.

Oct 1, 2003

By Gary M. Bone

The autonomous control of vehicles interacting forcibly with their environment, such as dozers and tractors, is an unsolved and challenging problem. Forces and motions are inherently coupled between the tool and the means of vehicle propulsion. Furthermore, they are often operated within uncertain and unstructured environments, such as those encountered in underground mining. There is a growing industrial interest in the development of robotic vehicles to improve productivity, efficiency and safety in mining and construction. This paper focuses on the modeling and control of autonomous robotic dozing for a material removal operation. A dozing process model has been developed based on observations of both a fullscale dozer and a scaled-down version. The model characterizes the dynamic interactions between the blade position, material accumulation on the blade, material distribution in the environment, and the motions of the dozer. The dozing control objective is to remove the loose material as rapidly as possible by driving forwards at full power while automatically raising/lowering the blade in response to sensor measurements. Two different controllers were developed to meet this objective. The first controller is based on a set of heuristic rules, and the second is an optimal controller based on the dynamic model. An instrumented scaled-down robotic dozer and dozing environment, designed to emulate the full-scale operation, are used to implement the controllers and compare their performances over multiple dozing passes. Experimental results are presented showing that the model-based controller increased the material removal rate by 33% compared to the rule-based controller. Lastly, technologies for full-scale implementation are discussed, followed by proposed future work and conclusions.

Aug 1, 2013

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By J. P. Messervey

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By H. Itou

A mechanism of scorodite formation at ambient pressure was investigated using transmission electron microscopy (TEM). Several types of iron arsenate were obtained from Fe/As solutions (Fe/As = 1.0 and 1.5) at pH values of 1.0, 1.25 and 1.5 at 95°C. Amorphous FeAsO4.xH2O was precipitated from solutions having a higher mole ratio of Fe/As at pH l.5, even after 9 hours. A few micron sized particles were observed by SEM, but these proved to be agglomerates of 10-50 nm amorphous FeAsarxH2O particles when observed by TEM. This means that supersaturation of the solution causes the acceleration of nucleation of iron arsenate hydrate. Crystalline scorodite was obtained from a solution in which the Fe/As mole ratio was unity, at pH l.0 and pH 1.5, after 3 hours. Almond-type crystalline scorodite particles were observed by TEM and most of them showed high crystallinity. The addition of scorodite seed material enhanced the crystallization. Amorphous FeAsO4.xH2O, however, was observed at the surface of the seeds during the early stages of precipitation. It is postulated that crystalline scorodite is not directly precipitated even on crystalline scorodite seeds, but requires a certain time to crystallize on the seed material.

Jan 1, 2006

By D. Mills, W. J. Brantina

"Mechanical and magnetic characteristics of ferromagnetic materials were investigated by a pulsed ultra-sonic technique. Two instruments, the Ultrasonic Attenuation Comparator (Sperry) and the standard type Reflectoscope (Sperry) were used for measurements of the attenuation of the ultrasonic pulse. The effects of elastic tensile and compressive stresses on the attenuation of annealed and cold worked material are described. In addition, the effects of plastic de-formation, relaxation and aging processes and different ultrasonic test frequencies are reported. The results for Armco iron, SAE 1020 steel, SAE 4340 steel and AISI 420 stainless steel are shown. Under the test conditions, the attenuation was found to be largely a sum of two components; a ""dislocation"" component associated with the losses accompanying the oscillations of dislocation line segments and a ""ferromagnetic"" component associated with the microeddy currents generated by magnetic domain wall oscillations. Either of these components might be dominant depending on the nature of the particular specimen and the test conditions. Finally, the possibilities of using ultrasonics in residual stress determinations, in fatigue studies and in the study of the ductile-brittle transition in ferrous materials, are briefly discussed."

Jan 1, 1960

By PAUL L. DEAN

Industrial mineral deposits are widespread in Newfoundland and Labrador and a variety of commodities are produced. The province has the only pyrophyllite mine in Canada and also produces asbestos, gypsum, silica, barite, limestone, gemstones, cement and other structural materials. Large reserves of these and other industrial minerals are known and several deposits are likely future producers. Most producers are wellestablished and have large tonnages of ore reserves.

Jan 1, 1984

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

By C. W. K

This little sketch of the late Willet G. Miller, Provincial Geologist of Ontario, is intended to be neither a biography of his career nor a eulogy of his life. His biography has already been written in an incomparable manner by Mr. T. A. Rickard, his eulogy by Canon Cody. What more can be said of Dr. Miller than is summed up in the words of that great Canadian divine, Canon Cody, that he was "Big in body, big in heart, and, as we learned, big in brain." This article, then, will merely record a few personal reminiscences of the man himself, and while they are necessarily disjointed, they may at least serve to illustrate certain traits in his character which are not generally known or appreciated outside of the circle of his intimate friends. In the latter part of May in the year 1904, Willet G. Miller, with two? assistants, set out for the small village of Haileybury to begin his geological work in the area a few miles to the south which he was soon to name Cobalt. At that time the Timiskaming and Northern Ontario railway was not finished, although the right-of-way was cleared and partly graded. The nearest railway station was on the Canadian Pacific at the south end of lake Timiskaming, from which point the old steamer Meteor carried passengers and freight up the long, narrow and deep waters of lake Timiskaming, a very pleasant trip of some sixty miles. On this particular trip there was a fairly large crowd on board consisting of settlers going into the clay belt north of lake Timiskaming, of lumbermen, and of a few merchants and commercial travellers who were interested in the small business centres of Haileybury, New Liskeard and Ville Marie. Scarcely any attention was paid to the reports of the newly found silver deposits, although the daily papers had announced discoveries in the district six months before. As a matter of fact, the chief excitement on board was afforded by a moose, which, in swimming from the Ontario to the Quebec shore of the lake, crossed the bow of the boat, the captain steering to within a few yards of the terrified animal.

Jan 1, 1925

By M. H. Kotze, V. Yahorava

A gold-selective ion exchange resin, containing tributylamine groups, was developed by Mintek for the recovery of gold from cyanide leach solutions. The Dow Chemical Company and, more recently, Purolite commercialized the production of this gold selective resin for use in the gold mining industry, and it is marketed as Dow XZ-91419.00 and Purolite A194 respectively. A novel application of this resin is the selective recovery and separation of AuCl4 - f rom p latinum group metals (PGMs) in chloride and nitrate solutions. The current paper describes potential benefits of this type of resin for selective recovery and upgrading of gold from low grade chloride or nitrate waste streams, and the possibility of gold separation from PGMs during their refining in chloride media.

Jan 1, 2014

By Bo R. Arvidson

"New permanent magnetic alloys have recently opened up possibilities for development of unique mineral separators. These are now making several new applications feasible. In many cases where conventional electromagnetic-induced roll separators have traditionally been used, the new permanent magnetic roll separators may reduce both over-all capital costs and operation costs.The development of the next generation of extremely powerful permanent magnets, i.e. neodymium-iron alloys, is progressing rapidly and will affect the roll separator as well as another type of magnetic separator. Permanent Magnet Roll SeparatorDesign and FeaturesDiscs of permanent magnets interleaved with soft iron discs constitute the basic magnetic roll design (Fig. I). By enveloping the magnetic roll with a thin abrasive resistant belt (Fig. 2), even highly magnetic particles are removed.The first prototype roll utilizing the new magnets was shown to have approximately equal strength as induced magnetic roll (IMR) separators. Since the initial test roll, the new separator, called the PERMROLL® , has been made twice as strong with regard to magnetic force, that is, the magnetic flux density is determined to exceed 1.7 tesla (17 kilogauss), while the magnetic field gradient is more than twice the gradient than can be practically achieved with IMR."

Jan 1, 1985

By X. Z. Yuan

Contamination introduced by the impurities from the feed stream can impact the PEM fuel cell performance dramatically. The presence of these unwanted trace species such as CO, H2S, NH3, can adversely affect the fuel cell functioning. It has been reported that the major impact of CO and H2S contamination on the fuel cell performance is kinetic while the effect of NH3 contamination is speculated as membrane conductivity reduction only. In this paper, a model regarding the NH3 contamination is described and the mechanism of the NH3 contamination is illuminated by the model calculations.

Jan 1, 2005