Search Documents

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By H. H. Bleakney

The merit of reduction-in-area as a criterion of quality in metals is shown to lie in its influence on breaking stress, but the virtue of elongation is not easy to find. In order to assess the value of elongation, either as a measure of quality or as a guide to design, it will be necessary to separate the overall de-formation occurring in tension tests from the localized deformation associated with localized reduction in area. The obstacles to a successful solution of this problem have been shown to be more formidable than is generally appreciated, and a new solution to the problem has been suggested. This solution involves a de-vice by which an electric circuit is broken when the particular value of strain is reached that is to be taken as the point of separation between general and localized deformation. The report presents results from a number of tests on both low-carbon and alloy steels. These results indicate that the selected criterion of separation is accurately identified by the proposed method; that it

Jan 1, 1962

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By S. N. Aliferova, E. I. Afonina, S. N. Titkov, A. Ju. Bondareva, N. N. Panteleeva

"Potash ore is mainly processed using the method of cationic flotation. Potash ore deposits of the CIS, namely: at Upper Kama river, Gremyachinsk (Russia), Starobin (Belarus), Tubegatan (Uzbekistan) are characterized by relatively low KCl impregnation (1.0 – 1.5 mm) and contain up to 10% of waterinsoluble impurities (WII). Water-insoluble impurities are presented by aluminosilicate, silicate, carbonate (calcite, dolomite) minerals and anhydrite. In the process of milling the ore to a flotation size there are released and dispersed the insolubles impurities actively sorbing the cationic collector, i.e. aliphatic amines C16 – C22. In this regard there is carried out a preliminary desliming of the ore.Currently grinding the ore to a flotation size (1.5 mm or less) is carried out in rod mills along with forming of a large number of fine-grained ore fractions having the size under 0.25 mm, which results in the increased KCl losses with halite slime waste and reduction in the quality of finished product. There has been developed the technique for processing of potash ores with a high content of water-insoluble impurities (10 – 12%) containing, in different ratios, silicates, carbonates and anhydrite. The technology involves the use of the ore dry grinding to the flotation size and subsequent reagent activation of the processes for sludge removal and sylvite flotation.INTRODUCTIONCurrently there are being developed the potash ore deposits in the CIS countries, namely: at Upper Kama river and Gremyachinsk deposits (Russian Federation), Starobin deposit (Republic of Belarus) and Tubegatan deposit (Uzbekistan). Potash ores are a mixture of sylvite and halite and contain water-insoluble impurities of silicates, carbonates and anhydrite. The content of water-insoluble impurities (WII) reaches up to 10%, disseminated (impregnated) sylvite does not exceed 1.5 mm and in connection with that the ore is crushed to a particle size under 1.5 mm. Ore grinding is performed by wet process in rod mills with producing a significant amount of fine-grained mineral fractions and sludge, which are actively sorbing a cationic collector, i. e. primary aliphatic amines C16 - C22. The ground ore is deslimed and the slime product is directed to a sludge depot (pits)."

Jan 1, 2016

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005

By J. M. Cummings

The importance of controlled sand properties to the production of quality castings has been recognized by foundry men for many years, but the maintenance of requisite standards results in a relatively high sand consumption, which in steel foundries, for instance, may range from half a ton to over one ton of sand per ton of finished casting. During the war, obtaining and maintaining adequate sand supplies became a serious problem in many foundries, owing to increased wartime production and serious 'bottlenecks' in transportation. As a result, considerable interest was aroused in the possibilities of various sand reclamation systems by which up to 85 or 90 percent of discarded sand may be returned to a usable condition. During the past five years or so, a number of sand recovery installations have been made by both ferrous and non-ferrous foundries in Canada and the United States, and have resulted in substantial reductions in sand costs in every case. The possible benefits of sand reclamation are particularly apparent in British Columbia where no suitable sands for steel and heavy iron foundries occur naturally, and where freight costs on imported sands are considerably higher than initial selling prices. This is well illustrated by the fact that silica sand, which sells for about $2.00 per ton at pits in Illinois, is laid clown in British Columbia for around $11.00 or $12.00 per ton. The operating costs quoted for certain of the reclamation schemes, i.e. $0.25 to $1.50 per ton, may actually be no higher than the cost of waste sand disposal in city-located foundries. In view of the foregoing considerations, the British Columbia Research Council has undertaken a study of the possibilities for sand reclamation, with particular attention directed to its application in local steel foundries. No commercial occurrences of silica sand are known in the Province, and, with this in view, the Council previously investigated the possibility of recovering silica sand from local impure sands. Results were definitely encouraging, but it was felt that the present market is too small to permit economical production by the method developed.

Jan 1, 1947

By Willem P. C. Duyvesteyn

"Scandium International Mining Corp (SCY) has been involved in the commercial development of its Nyngan Scandium Project for about ten years. Various studies at a variety of global R&D organizations have been carried out in an attempt to define the deportment of scandium in both the limonite as well as the saprolite phases of Nyngan ore to assist with process development. Technologies such as sulfuric acid baking, high pressure acid leaching, sulfuric and hydrochloric acid atmospheric leaching and heap leaching have been extensively investigated both at the bench and pilot scale level to arrive at the most economic process flow sheet that will be discussed in some detail in this paper. Solvent extraction, ion exchange and other refining technologies have been tested and an optimum configuration has been established for the Nyngan project which is expected to be the first primary scandium mine and metallurgical plant in the world.Because of a lack of product availability the current scandium market is limited to less than 20 tons per year. Technologies have been identified to produce product with different specifications for aluminum alloys and solid oxide fuel cell applications. Preliminary economics have identified that Nyngan will be a robust and low capital cost project that can readily be expanded as the size of the scandium market increases."

Jan 1, 2016

By N. Aslin, R. Clark, G. Heferen

The methods of harvesting copper from stainless steel mother plates has been investigated from fundamental and operational experience perspectives. At least five different harvesting techniques have been identified that have different effects on product quality, current efficiency, current distribution, growth morphology and ease of stripping. Each method is examined from fundamental principles to understand what occurs during the harvesting process and why the particular effects are manifested. Experience from plants operating the harvesting method is provided to show that the fundamental understanding is relevant. Best practice harvesting method and harvesting management are described.

Jan 1, 2014

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By M. Lindgren, M. Latva-Kokko

Process performance can be significantly influenced by proper design of hydrometallurgical reactors. Optimal reactor configuration is case specific and depends on process requirements such as reaction rate limiting factor and particle size distribution. Choice of materials and manufacturing methods also play important roles in highly corrosive and abrasive environment often involved in hydrometallurgical industry. In this paper performance of different reactor designs has been compared in some typical hydrometallurgical applications. Results show that significant improvement in energy consumption, gas utilization efficiency and equipment lifetime can be achieved with process specific reactor design.

Jan 1, 2014

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006

By Robert P. Dufresne

Electrolytic cells are used in electrowinning (EW) and electrorefining (ER) of non-ferrous metals such as zinc and copper, and are a critical part of the purification process. The cell is a large basin and has an electrolyte or aqueous solution, an anode and a cathode, an insulator, and incoming high amperage. Cells are exposed to unfavourable internal and external factors that have a direct impact on their lifespan. Their deterioration can be caused by incorrect polarity, insufficient magnitude, their construction, tension stress, thermal shock, corrosion and other, and their maintenance and replacement can be time-consuming, costly, difficult and environmentally unsafe. Occupational health hazards and dangers posed by the maintenance and removal of the cell should also be taken into consideration. Modifying the design and fabrication method of the cell, using chemical-resistant reinforcement, and increasing tensile and mechanical strength will defer maintenance for a very long time. This can be achieved by a double hull system that comprises full-length composite reinforcement, polymer concrete reinforced with fiberglass pultruded rods and rebars, fiberglass structural layers, and special resin matrices. This will provide protection against thermal shocks, corrosion, leakage, cracks. The design of this cell incorporates a lifting system that will afford quick and easy install without having to move a great number of cells in close proximity, since it is strong enough to stand on its own and not have to be bonded to adjacent cells. As well, the cell can be anchored with ease as it remains stable. This is especially important because space is limited to lift and manoeuver between the cell and the double-girder overhead travelling cranes. The lifting system can also prevent electrocution and loss in product quality, while increasing efficiency and safety in the workplace. Considerable savings in terms of production downtime are also part of the equation. INTRODUCTION Maintenance and replacement of electrolytic cells in electrowinning and electrorefining are operations that pose many challenges, health and safety concerns, and give rise to substantial operational costs. These problems have existed since time immemorial. Electrolytic cells are made of conventional concrete or polymer concrete, and because of the very nature of their composition and their exposure to severe and environmental conditions, their lifespan is short. Although polymer concrete is composed of high-quality materials, and has good thermal stability and resistance to chemicals, nonetheless, maintenance is frequently required in order to maintain the integrity of the cell and to ensure the quality of refined metals. Repairing concrete is a non-permanent solution as cracks will reappear, and every repair weakens the integrity of the cell a bit more, until it reaches a knock- down point and the structure is compromised. The cell needs to be replaced, otherwise the cell will collapse.

Jan 1, 2019

By W. R. A. Graeser

"The Nordenham finishing mill is situated in the town of Nordenham, Fede1•al Republic of Germany, on the banks of the Weser River opposite the town of Bremerhaven, with access by water to the North Sea.The unfinished fibre, shipped j?•om Deception Bay during the sub-Arctic summer shipping season, is unloaded from bulk ocean carriers, stored and then processed throughout the year until the following shipping season. This paper describes the unloading and storage facilities,the finishing mill and the finished-fibre storage arrangement. Details of environmental and dust control practices and West German environmental standards are discussed. A resumé of fibre markets is included."

Jan 1, 1976

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By M. A. Hardie

"CASES and mixtures of them are so common and so much a part of everyday existence that they become so taken for granted that their individual characteristics and idiosyncrasies rarely become of curiosity to others than those involved in tl1eir production, processing, treatment, transportation, and for utilization. The use of the most common and universal mixture of gases -air -is begun at birth by ail living creatures and their discontinuation of its use terminates existence. Modern man rides on air in his tires, rides through it for high-speed transportation, and uses it for his comfort in the heating and air conditioning of his domicile. It is neither the aim nor the in-tent, in the next few moments, to provide a panacea for even a portion of the problems inherent in the gas industry nor to delve deeply into any particular facet of its diversities. The purpose is primarily to touch upon some of the peculiarities and generally to consider approaches to employ in the pursuit of solutions."

Jan 1, 1959

By R. W. Nice

Presently about 60% of the world's nickel resources are tied up with lateritic ores while about 25% of the world's nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By K. H. J. Clarke

"ALTHOUGH nickel was not identified as a separate element until a Swedish scientist, Axel Frederick Cronstedt, did so in 17 51, its utilization dates from pre-historic times. From its humble beginnings nickel has grown in importance until, today, in our clocks, television sets, automobiles, and air-planes, in our bridges, tableware, farm implements, and the equipment which processes our food, it is constantly at our service.For convenience in assembly, data and information relative to The Marketing of Nickel will be outlined in five phases: (A) Sources, (B) Distribution, (C) Utilization, (D) Market Development, and (E) Conclusions."

Jan 1, 1960