Search Documents

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By William Petruk

Image analysis studies were performed on mill products from pilot-plant and laboratory tests that had been conducted to determine the effect of grinding media on the selective flotation of two zinc-lead-copper ores. It was found that, when the ores had been ground to the same degree of fineness with flint pebbles, ceramic pebbles or ore fragments (autogenous grinding) as with steel balls, there generally was increased sphalerite, chalcopyrite and galena liberation in the flotation feeds, depending on the textures of the minerals. The increased sphalerite liberation fully accounted for the improved zinc recoveries that were obtained when steel balls were replaced by either pebbles or ore fragments. The increased chalcopyrite and galena liberation accounted for part of the changed technical efficiency of concentration, but other factors, probably changes in oxidation and reduction of iron and in consumption of oxygen, also contributed.

Jan 1, 1977

By William Petruk, J. R. Schnarr

The behaviour of minerals during flotation of a fine-grained pyrite-rich base metal ore was investigated by studying the feeds. concentrate and tailings from every flotation cell in the mill of Brunswick Mining and Smelting Corp. Ltd. Bathurst. New Brunswick. The samples were analyzed for Zn, Pb, Cu. Fe, Ag. Sb, Sn, Bi, In. Hg, Mo and As. Mass balances were computed and recoveries of all metals from each cell. from each circuit and from the mill were calculated. The percentages of sphalerite. galena and chalcopyrite occurring as free grains in each product were determined with an image analyser, as were size analyses for free mineral grains and middling particles, and compared with screen analyses. The results show that the behaviour of minerals is defined much better by the recovery of free mineral grains than by the recovery of elements. The recovery of free sphalerite in the zinc circuit is 96 wt %, whereas Zn recovery from the same circuit is 88 wt %. the difference being due to unliberated sphalerite. The recovery of free sphalerite from the mill feed is 88 wt % and Zn 78 wt %. The recovery of free galenafrom the mill feed is 88 wt % and Pb 64 wt %. The recovery of free chalcopyrite is 75 wt % and Cu 45 wt %. Size analyses show that more sphalerite and chalcopyrite can be liberated by regrinding. but the galena is so fine grained that regrinding would not necessarily improve liberation. Silver occurs mainly in tetrahedrite and galena; the main loss in the tailings is due to large (+ 26 um) and small (-1 um} free and unliberated tetrahedrite grains.

Jan 1, 1981

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

By Zhitong Sui, Feng Zhang, Li Zhang, Tie Ou, Guangqiang Li

Researches on the recovery of iron, manganese and the removal of phosphorus from converter slag were reviewed. The carbon thermal reduction experiments were carried out by induction heating the mixture of converter slag and graphite powders at 1650°C and 1800°C in a graphite crucible. It was found that 62.7% of the phosphorus in converter slag was reduced into carbon saturated iron alloy, 32.8% of that was vaporized and only 4.5% of that remained in the final product. Totally 95.5% of the phosphorus in converter slag was removed. Almost all iron and manganese was reduced to form carbon saturated alloy. It was found that the free lime in converter slag can react with carbon to form calcium carbide at 1800°C. The main phases in the reduced converter slag are dicalcium silicate and tricalcium silicate with small amount of calcium carbide.

Jan 1, 2004

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By Ben R. Bjorkman

The future is here ? or at least that?s what Mine Planners predicted some 15 years ago ? that by 2004 we would have man-less mines running themselves using space-aged technology. Truthfully, though, there hasn?t been much change in mining methods in the past decade, but thankfully that?s all about to change. The benefits of autonomous ? even Tele-operated mining (especially in narrow-vein ore bodies) are wellknown: increased production hours by eliminating travel time to and from the face, continuous production at the face while crews screen and bolt behind the working equipment, less liability for workers? safety in certain areas, etc. But when plans are put in place to accomplish this vision, things stagnate and production carries on as before. This paper examines the components necessary to make that vision a reality. First we?ll detail the technology required to enable Tele-operation ? even autonomous operation of mining machinery, then we?ll look at what?s wrong with the current way we?re mining, and finally conclude with a critique of the machinery itself.

Oct 1, 2004

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By Neil McMillan

"By any measure of common practice, Claude Resources' Seabee Gold Mine in Northern Saskatchewan should not now be operating. Not because reserves dwindled, or grade dropped or prices weakened or technical problems arose, but because a host of unimaginable other problems beset the project, any one of which would normally have led to the mine's failure.The success of the Seabee Mine, and it is extremely successful, is a story of the vision and blunt determination of two men. Neither is remarkable in his own right but each possesses the characteristics which were necessary to forge a highly productive and profitable narrow-vein mine in the midst of the most bizarre and unpredictable events which likely have ever beset a mine start-up in Canadian history.Together, Bill MacNeill, a Saskatchewan born, former bush pilot and Ray Gagnon, a big hearted, hard-fisted, miner with 44 years of experience in Canada's underground, built the Seabee Mine.They didn't accomplish this with brilliant geology, outstanding engineering or nimble corporate manouvering but rather a stubbornness and raw common sense which likely are all too often, ingredients missing in failed projects.The Seabee Mine is 100% owned by Claude Resources, a Saskatoon based company taken over by Bill MacNeill, its current chairman, in 1982. The company is listed on the TSE and produces 1200 barrels of oil per day and about 60,000 oz of gold per year. The company has a strong balance sheet, is very profitable and has 18 million shares outstanding.The Seabee property in Northern Saskatchewan started out like many other gold exploration properties in Canada.It was discovered in the l 940's by what is now Cominco, and, while highly regarded by that company the property sat largely dormant until acquired by Claude Resources in 1985.Claude did what most junior exploration companies would do and went looking for a company with a depth of expertise to joint venture the property.That company was Placer Development who could earn a 55% interest in the Seabee by delivering a bankable feasibility study on the Project by July 1988 and providing financing to production.Placer Development was an excellent company and spent over $8 million dollars on the Seabee over a 3 year period. Unfortunately for Claude Resources, Placer Development merged with Dorne Mines in 1987 and the new merged company, Placer Dome, established a minimum production threshold greater than the 50,000 oz per year which the Seabee appeared capable of supporting at that time. Placer Dome's request for an indefinite extension of the joint venture agreement to allow it to drill off a larger ore body was rejected by Claude Resources and the Seabee Property was returned to Claude in 1988."

Jan 1, 1998