Search Documents

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector's problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By Percy Coulter

"GeneralThe Malartic Gold Fields mill is presently treating ore from four different companies. The ore is delivered by truck, by the shipper, and dumped into the Malartic Gold Fields ore bin. This ore varies in size from 'Run of mine' to minus 8 11, All ore is crushed to pass a 3/ 8 11 x 4 11 cross slotted screen.Weighing and SamplingAfter crushing the ore passes over an adequate-weigher (250 T .P.H. capacity) on its way to the fine ore bins. This weigher has a remote counter at the sampling point.A 36” Vezin sampler cuts 15% from the ore stream as it enters the mill bins. This portion is elevated, by means of a short belt conveyor, to feed the No. 2 Vezin sampler. (This elevation is necessary to give headroom for the following machines). The ore on the conveyor is levelled to give a uniform stream to the second sample cutter. The second, third and fourth cutters are 2411 •The No. 2 Vezin sampler cuts 19% from its feed and this portion falls directly into a 1611 x 1011 Denver rolls crusher. This crusher reduces the ore to -1/ 8 11 , approximately. The discharge from the rolls crusher falls on a revolving circular plate with scraper, which gives a uniform stream to the No. 3 Vezin sampler.The No. 3 Vezin cuts 10% from its feed. This portion falls on another revolving plate to give a uniform stream to feed No. 4 Vezin."

Jan 1, 1966

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By R. J. Traill

Introduction Following the discovery of high-grade deposits of pitchblende in the Great Bear Lake area of the Northwest Territories by Mr. Gilbert LaBine in May, 1930, samples were submitted to the Mines Branch for examination and investigation as to suitable methods of treatment (1). The purpose of this paper is to present, briefly, the results of the investigative work conducted on the ores and an outline of the methods developed for the extraction of the radium content and recovery of the by-products. The paper is presented in two parts. Part I gives a review of the history of radium production and of the principal processes used in other countries. Part II describes the work and gives the results of the Mines Branch investigation. Part 1-Radium Production In Other Countries Historical Outline Uranium was discovered in 1789, and more than a century later Madame Curie, while studying the physical properties of this element, observed that the ore of uranium exhibited greater activity than the pure uranium com-pounds she had prepared and traced the cause to the presence of a new element which she named radium. Eventually, research proved radium to be a disintegration product of uranium, and always present in uranium ores.

Jan 1, 1933

By F. Romero

In the last four years, Compañia Minera Doña Ines de Collahuasi has been working in the application of advanced multivariate statistical techniques for the improvement of the metallurgical processes. In this paper the main conclusions for the application of multivariable analysis to the EW process are presented; including the identification of (target) process patterns according to throughput and quality criteria. Based on the process patterns, process variables hierarchies were identified by selecting the most influential ones, as well as to identify and isolate the root causes of pattern deviations and sub-standard operating conditions, cause-effect relationships were established, leading to the definition of process policies and controls to give early corrections to potential failures. The analysis was focused on cathode quality, specifically in its sulfur content, using an empirical model based on those variables that from a phenomenological and statistical stand point appeared to be the most influencing ones.

Jan 1, 2007

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By A. Anderko, R. D. Springer, R. D. Young

A thermodynamic model has been developed for calculating phase equilibria and other properties of multicomponent electrolyte systems. The model has been designed to reproduce the properties of both aqueous and mixed-solvent electrolyte systems ranging from infinite dilution to solid saturation or pure solute limit. The model incorporates formulations for the excess Gibbs energy and standard-state properties coupled with an algorithm for detailed speciation calculations. The excess Gibbs energy model consists of a long-range interaction contribution represented by the Pitzer-Debye-Hiickel expression, a second virial coefficient-type term for specific ionic interactions and a short-range interaction term expressed by the UNIQUAC equation. The accuracy of the model has been demonstrated for common acids and bases and for multicomponent systems containing aluminum species in various environments.

Jan 1, 2005

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

By K. Morin

"Silver and gold leaching by cyanidation is a well-known process used around the world. This reaction is often accompanied by the leaching of other species throughtout the cyanidation circuit that causes the diversion of cyanide towards non valuable by-products (SCN-, Cu(CN)x, Fe(CN)x, etc.). One of the detrimental impacts of the formation of these by-products is the precipitation of silver-cyanide complexes that occurs when cyanide concentration is too low. Without any extra-addition of free cyanide, the precipitated silver is lost and cannot be recovered causing an important economic loss. To overcome silver precipitation, cyanidation circuits are often operated at higher cyanide concentrations. Recently, COREM’s research team has been working on a technology to measure and control silver precipitation during the cyanidation process. Moreover, a methodology has been elaborated in order to evaluate threshold cyanide level which corresponds to the cyanide concentration at which silver starts to precipitate. This technology has been tested on site on a real cyanidation circuit at Agnico Eagle’s LaRonde mine."

Jan 1, 2014

By Brian Flintoff

"When I was first asked to prepare this paper and presentation in late June, I thought it might be fun to ""step back and paint the bigger picture."" Having attempted to do this, fun is not the first descriptor that now comes to mind, and speaking dyslexically, I've had 'nuf.'Unlike Nostradamus, or even Orwell, I've discovered that I'm ""clairvoyantly challenged"" and not even the psychic hot-line was of much help, at least with respect to process control! I am somewhat comfortable speculating on evolutionary change, but the radical developments that will arise from revolutionary changes are well beyond my mortal capabilities. Even with evolutionary change, I'm reminded of the lessons of time series analysis which show the prediction error to grow exponentially as the horizon moves into the future. As Macluhan is reported to have said: ""Predicting the future based on the past is a little like driving your car while looking in the rearview mirror!""Having honestly presented my qualifications, allow me to try to look at process control and to offer some conjecture on where we're probably headed. In the end, it is said that: ""The plant of the future will have only two employees, a man and a dog. The dog will be there to keep the man from touching the equipment.1""IntroductionA little less than a decade ago Andy Mular and I co-edited a monograph entitled ""A Practical Guide to Process Control in the Minerals Industry."" The work was commissioned by the senior management of a consortium of Canadian mining companies, since it was widely perceived that control was an area of great economic potential, but one that had not been effectively tapped. The concern was that if the industry could not soon deliver on the ""potential"", the term may well have appeared in the epitaph of what was, to these men, a very attractive investment opportunity. I think it is fair to say that over the past few years process control has clearly established itself as an essential technology in plant operation and optimization. That isn't to say that we get it all-right, all-the-time, but, the circumstances are much different than they were. In the eyes of many, process control has attained the distinction of being considered a mature technology, even though there are still countless avenues for exploration."

Jan 1, 1998

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre- 1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati will be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2003

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT: As part of an overall study of properties and processes influencing consolidation of oil sands fine tailings resulting from different extraction processes, self-weight consolidation tests were per-formed. Fourteen 2 m and 1 m high standpipe tests were instrumented to monitor the rate and magnitude of consolidation of seven fine tailings materials. Tests provided valuable information about the variation of consolidation related to differences in fine tailings material properties that result from a change in bitu-men extraction process (caustic versus non-caustic). In addition, the effect of adding a coagulant to caustic fine tailings was measured. Test results are presented and discussed in terms of consolidation rate long-term volume decrease, compressibility, and downward drainage. Non-caustic fine tailings had fasterinitial consolidation, which is important in tailings ponds for reducing storage capacity and returning decant water at a faster rate to the extraction plant. Similar results were obtained for caustic fine tailings with a coagulant addition. However, long-term settlement of the different fine tailings appears to con-verge to a similar value over time because it is then governed by effective stress.

Jan 1, 2011