Search Documents

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

By R. Venugopal, Saxena. V. K., U. Sankrityayan

"There is a dire need of a technology which can break the mineral interfaces to enhance liberation with minimum energy consumption in mineral beneficiation processes. Understanding of mineral crystal system and interfaces is essential to develop such methodology. So, this study is carried out to find out the role of mineral crystallography in milling and liberation. Data related of mineral crystallography, Vickers Hardness Number, Bond Work Index and beneficiation processes were collected from literature and detailed statistical analysis has been carried out to establish a correlation among these parameters. It was found that atomic weight and cell parameters shown statistically significant relationship with Vickers Hardness Number of minerals, which controls the milling characteristics of ores. Liberation characteristics of five different kinds of ores were analyzed considering the types of interfaces between valuable and gangue minerals. It was found that phase interfaces play vita role in liberation and coarser liberation can be achieved in the minerals of incoherent crystal systems like manganese and zinc ores. Study of this subject can help us to understand the effect of stress wave propagation in solids and its effect on crystal interfaces. It can also help us to design a technology of future to break the mineral interfaces.INTRODUCTIONCommunition is energy intensive mineral processing operation and consumes up to 2% of the total electric power generated in the world. Energy consumption due to comminution is increasing every year as there is growing needs to exploit lower grade ore bodies and process rejects (Blazy et al., 1994; DOE, 2005). Low grade ores require crushing and grinding to liberate the valuable minerals which are further separated from gangues by various beneficiation methods like gravity separation, floatation, leaching etc. Currently, comminution methods are selected based on the reduction ratio and energy consumption but effect of grinding methods on subsequent processing methods specially on liberation also need to be studied to optimize the entire beneficiation process. Most of the attempts made in past to minimize the energy consumption in milling to enhance the mineral liberation were focused on compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Kilpelm and Austin, 1982; Norgate and Weller et al, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang el al., 2011; Singh et al., 2012). But the role of mineral crystallography on milling and liberation behavior of minerals not fully explored yet."

Jan 1, 2013

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By Sandra K. Zacharias

Brass, a deliberate alloy of copper and zinc, has been known since before Roman times. There are two main methods of making brass: (1) Cementation or calamine process - crushed zinc ore (calamine, ZnC03 , or calcined calamine, ZnO), is mixed with charcoal and small pieces of metallic copper and heated to about 900°C in a closed crucible, (2) Alloying - metallic copper and zinc are melted together in a reverberatory furnace. According to most modern authorities (e.g. Smith and Forbes 1955), the calamine process was the only one used in western Europe prior to the 18th century. At that time, the alloying technique began to take over, because metallic zinc was successfully produced on a large scale for the first time. Previously, this had been a problem because zinc vapourizes at 906°C or about the same temperature at which it can be reduced from its ore. Thus, some means had to be devised to collect and condense the zinc vapour (Tylecote 1976). Metallic zinc was known, however, earlier than the 18th century A.O. Several early finds have been made, including a rolled sheet of metallic zinc found in excavations at the Athens Agora dating to the 3rd to 2nd century B. C. (Farnsworth et al. 1949). The Chinese were producing zinc by at least the 10th century A. D. and, by the 17th century, Chinese zinc ingots were being imported into Europe by the Dutch East India Company (Needham 1974). Metallic zinc is also mentioned in several European documentary sources from the 16th century (e.g. Paracelsus, Agricola). This study traces the changes in Western brass making methods from Classical to Renaissance times by examining documentary and archaeological evidence.

Jan 1, 1999

By R. L. Stanton

"The present contribution is complementary with a preceding one on the field association of the conform-able ""pyritic"" deposits. It considers the more important features of their mineralogical constitution and their microtextures, re-examines the present interpretations of these, and of-fer-some alternative explanations. The term ""pyritic"" for these de-posits is m many cases a misnomer, as two quite distinct ore types are inuolve. One is a banded pyritic sphalerite-galena-chalcopyrite ore (for which the term '•pyritic"" is in-deed quite suitable), while the other is non-banded and is composed essentially of pyrrhotite and chalcopyrite. In addition to these constitutional differences, each is distinctive in general appearance and texture. The occurrence of two such consistent but clearly distinguishable ore types is attributed -rather than to difference in source material and pressure-temperature conditions of deposition -to the contribution of similar source material to dissimilarly oxygenated environments of sedimentation. Textures in the banded ores generally thought to be indicative of replacement or of high-temperature exsolution are explained by slow, law-temperature segregation in situ during compaction, folding, and regional metamorphism."

Jan 1, 1960

By G. P. Demopoulos

The solubilities of calcium sulfate in HCl-CaC1z-H20 solutions up to 100°C were successfully modelled with the aid of OLI software after bringing proper modification to it. Modelling, more specifically, was carried out with the help of the Environmental Simulation Program, V-6.6.0.4 (www.olisystems.com). New model parameters were obtained by regressing the solubility data. A private databank was established by adding the newly defined model parameters and the calcium sulfate hemihydrate phase that is not included in the original OLI database. The McGill-modified OLI software was successfully applied not only to modelling solubilities but also the transformation of the various CaS04 phases, namely dihydrate, hemihydrate and anhydrite. In this paper, the modelling methodology will be discussed along with a comparison of the capabilities of the newly developed model vs the original OLI model.

Jan 1, 2005

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019