Search Documents

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949

By C. Cristonffanini, S. Nazari

"In the past, simulation was considered to be an offline tool disconnected from plant operation. Advancements in the computation power combined with utilizing physics and chemistry sciences have allowed us to significantly improve the modeling and simulation technology for mining and mineral processing. This paper investigates the benefits of first principle models and simulation by connecting them to real time operation. Process data are connected to high fidelity models executed in parallel to the operation. In recent literature, this concept is known as Digital Twins. The Digital Twin is used for various purposes such as optimization, virtual instrumentation and condition monitoring. Using IDEAS™ simulation software we are able to construct a digital twin for different equipment inside a mineral processing plant. Two case studies for building a digital twin for the primary hydrocyclone feed pump and thickener underflow are presented. Using the pump’s model, a digital twin is developed and is installed in a gold extraction plant that is able to infer the slurry density in real time. Additionally, it is used for detecting sanding in the pipes and impeller condition monitoring.INTRODUCTION Since the eighties, thanks to advances in computation technologies, computer based simulation of processes using first principle models has become a well-known engineering tool for various industries. As our understanding of processes has increased, their representative models have become more realistic and more sophisticated. Due to this increase of accuracy, use of simulation is becoming more fundamental in process industries. The main goals to use accurate simulation is to decrease the engineering and construction cost, optimize the process design and improve the operation performance by decreasing operation cost and increasing efficiency. The term Digital Twin was first introduced in 2010 by NASA (Shafto et al., 2012) in aerospace industry. Subsequently, the concept quickly spread through other industries. As of today, no standard organization has provided an official and unique definition of Digital Twin for process industries. However, there are three important aspects that are common throughout various descriptions. When simulation is core functionality of the process (1) along the entire life cycle of the plant (2) with direct linkage to operation (3), it is called that process has a Digital Twin. According to Gartner, the concept of Digital Twin has elected as fourth most important disruptive technology for the year 2018 (https://www.gartner.com/, 2017)."

Jan 1, 2019

By John D. Godfrey

A brief account of economic developments in and around northeastern Alberta is presented and mention is made of mining and industrial developments currently of interest in the area. Planned and projected operations are briefly discussed for this region. The history of geological surveys and mining activities in the Shield area of Alberta and the adjoining parts of Northwest Territories and Saskatchewan is traced. Reassessment of the presently-known economic picture of northwestern Canada in conjunction with some recent information on Precambrian structures of northeastern Alberta points to some interesting mining possibilities, particularly in and around that province.

Jan 1, 1960

By Paul Miranda, Corby Anderson

"The Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently obtained a Mineral Liberation Analyzer (MLA). CAMP has utilized the technology for several projects with excellent results. The MLA is able to both analyze size and quantify mineral phases. Therefore, the MLA is becoming the Sherlock Holmes of the mining and metallurgical industry. For this presentation, four projects have been evaluated and data was collected using the MLA. The first project involved tungsten mine. Previous mining practices have yielded poor tungsten results and recoveries. By using the MLA, tungsten mineral phases, along with possible contaminants, were verified and the results used to try to increase overall tungsten recoveries. The second project evaluated a molybdenite/chalcopyrite concentrate with surprising results. The third project is a silver project. Initial flotation scoping tests were performed by attempting to separate silver from gangue material. Because of the poor recovery results (less than 5%), MLA was used to determine possible scenarios for increasing silver recovery. Finally, the last project involves gold evaluation in tailings. For all projects, MLA application results will be presentedand discussed.INTRODUCTIONThe Center for Advanced Mineral and Metallurgical Processing (CAMP) has recently received a software add-on to a scanning electron microscope (SEM) located at Montana Tech. The Mineral Liberation Analyzer (MLA) technology was developed by Dr. Ying Gu of the JKTech Center of the University of Queensland. Since August 2006, CAMP has received and processed over 50 samples. These samples include a total mineralogy of tungsten ore samples, gold tailings, lead zinc tailings pile, molybdenite concentrates, copper concentrates, as well as others. During analysis of these received samples, the technology allows the samples to be quantified mineralogically with some surprising results.For analysis, the samples were initially sieved between 170 to 200 screen sized mesh. This ensures that received samples mineral size is fairly uniform. The samples are then placed into epoxy and allowed to harden. Next, the samples are polished and carbon coated for MLA analysis."

Jan 1, 2007

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016

By J. P. Harrison, N. Bozorgzadeh, M. Dolowy-Busch

"It is common in rock engineering practice to characterize the triaxial strength of intact rock by using only data samples of small size. Practical guidelines such as ASTM support such sample sizes. In this paper, we investigate the reliability of the Hoek-Brown strength criterion estimated from such samples. For this purpose, we use an unusually large published set of triaxial strength data to randomly select a large number of data samples of small size to simulate the situation that frequently encounters in practice. The samples are generated with different arrangements with regards to the confining pressure. We fit the Hoek-Brown criterion to each of these samples, obtain estimates of strength parameters and compare them to those obtained from the complete data set. Our analysis suggests that estimates based on small samples are not reliable and can lead to both over- and under-estimation of strength.Additionally, we use these small samples to investigate the statistical methods for obtaining design values of strength as suggested by limit state design standards such as Eurocode 7. We show that, if used in conjunction with small samples, these methods do not guarantee a safe estimate of strength and in many cases lead to highly over-conservative estimates.We present a potential solution to this problem by augmenting the small data sets with Bayesian informative priors to give much more reliable estimates of strength. We conclude with suggestions for the development of informative prior distributions."

Jan 1, 2015

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By F. R. Nogas

"Because of the elements of uncertainty and instabilitp associated with single-enterprise communities, there is increasing interest in the alternatives to developing additional new communities of this nature. Gulf Minerals Canada Limited has chosen a unique alternative means to accommodate employees at a new uranium mine/mill complex at Rabbit Lake in Northern Saskatchewan. Gulf has adopted a fly-in program which moves their staff from a 450-mile radius, in and out of the on-site facilities, on a 7-day rotation."

Jan 1, 1976

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By T. H. Etsell, P. Kerr

Over the past 50 years, there have been a number of geological, mineralogical and metallurgical studies carried out on the Clear Hills ironstone deposits in northern Alberta, Canada. Due to the low grade and complex mineralogy, previous metallurgical studies have achieved limited success. After rejecting some of the more ‘conventional’ techniques for iron ore beneficiation, the authors chose to investigate the grain enlargement/iron segregation process for the beneficiation of the Clear Hills ironstone. The segregation reactions for iron have not been explored in as much detail as they have for copper and nickel. Iron segregation roasting involves the addition of a carbonaceous reductant and a chloride transport agent to an iron oxide ore, and heating the mixture to an appropriate temperature. The benefit of this process is that it allows ores in which the value minerals are intimately associated with gangue minerals to be processed in circumstances where conventional iron ore processing techniques are not suitable or capable of upgrading the material. As iron is one of the few elements that can be transported through this process, a clean high purity metallic concentrate can be achieved.Through the use of crucible testing followed by Davis tube magnetic separation, scanning electron microscopy, X-ray diffraction and atomic absorption spectroscopy analysis, characterization of the reaction products has been made with an improved understanding of the reaction mechanism.

Jan 1, 2015

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007