Search Documents

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

"IntroductionIn the 1970s, environmental concerns and associated liabilities were a new and unknown aspect of corporate risk. Today, social concerns and the associated conflicts that they can generate constitute a rapidly expanding aspect of risk. Although not a new phenomena — the Bougainville copper mine was forced into closure in 1988 — social risk has emerged as considerably more important, and increasingly visible, in the last few years. Social risk is now an aspect of all mining activities which needs to be calculated into project assessments, and to be managed throughout the life of a project. While social risk has a number of aspects at the corporate level, such as company image and shareholder relations, at the level of the individual project, its primary component is social acceptability, and the principal tool for managing it is the Social Licence to Operate.Social Risk in Latin AmericaThroughout Latin America there are newly modernized mineral codes and economic systems introduced over the last ten years which, together with new environmental legislation, look very much like regulations in developed countries. To the corporations, the existence of these instruments means that the risks from the environmental issues associated with the project are known; they are legislated, defined, quantifiable and hence manageable.It seems ironic that, just when comprehensive regulations for the environmental management of mining have been put in place throughout Latin America, there arise an increasing number of challenges to mining activities. For, in spite of the apparent guarantees provided by these new legislative reforms, communities in Latin America today are more frequently standing up and taking exception to the presence of mining companies, or the ways in which the companies are conducting themselves. The viability of projects becomes threatened because they are considered socially unacceptable, a phenomenon that we describe as social risk. These challenges are less about opposing mining activities than many people would think. Rather, they are based on an increasing desire on the part of the local population to have some measure of control over their own future, and to participate in the development process from the earliest stages."

Jan 1, 2000

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By K. G. Davies, M. J. Royea

"A major program of pillar recovery at the Sullivan mine has been assisted for the past several years by a concerted series of rock mechanics investigations. The object of these investigations is to measure the parameters of rock behaviour which influence pillar mining. This quantitative information is then used in the design of mining methods appropriate for various conditions.Instrumentation to measure absolute rock stress, changes in rock stress and the gross deformation of rock masses has been developed. Various instruments are described, as are instrument evaluation procedures and typical test results. The data from underground measurement projects have been used to modify pillar extraction sequences along re-treat fronts. Rock mechanics information from individual pillars has been incorporated into the design of mining methods to suit particular circumstances."

Jan 1, 1968

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By Magdy Ibrahim

This paper presents experimental design and development of a low-cost remote sensing hardware designed to support automated site data acquisition for near real-time progress reporting of construction operations. The developed hardware utilizes open source microcontroller equipped with multiple sensors that include 3D accelerometer, GPS, Data logger and Bluetooth. The use of open source microcontroller makes the developed design cost effective; freeing it from the need for costly license fees. Its platform configuration is flexible; enabling the addition of temperature, weight and other sensors, Wi-Fi and Xbee capabilities to suit individual field applications. Pilot tests have been carried out in laboratory and outdoor environments. The results prove effectiveness and robustness of the developed configuration. The paper provides description of the individual components used in the development of this prototype hardware. It also describes the technical characteristics, capabilities and limitations of the developed hardware. The findings of comparison with alternative technologies used for outdoor tracking of construction operations are presented. The comparison is carried out with respect to range, cost and suitability for outdoor environment. The developed hardware is expected to support a wide range of applications including tracking of earthmoving operations, highway construction and onsite resources. As well, it is expected to enhance safety on construction jobsites.

Aug 1, 2013

By J. G. Manchuk, M. Thurston

"The degree of uncertainty associated with a natural diamond resource is important to quantify from the time of discovery through the production lifetime. Data collection occurs during the discovery, exploration, delineation, and production or recovery phases. Quantifying the relationship between data and uncertainty is an important component of project valuation. The value of data is measured as their potential to reduce uncertainty if they are collected. A method is developed using Monte Carlo simulation for predicting resource uncertainty and valuing data during critical phases of development, particularly discovery and exploration. The technique is applied to diamond pipe deposits.RÉSUMÉ Il est important de quantifier le degré d’incertitude associé à une ressource diamantifère naturelle, depuis le moment de sa découverte et durant toute la durée de l’exploitation. La collecte de données se fait durant les phases de découverte, d’exploration, de délimitation, et de production ou de récupération. La quantification de la relation entre les données et l’incertitude est une composante importante de l’évaluation du projet. La valeur des données est mesurée en tant que leur potentiel à réduire l’incertitude si elles sont recueillies. Une méthode a été développée qui utilise la simulation de Monte Carlo pour prédire l’incertitude de la ressource et évaluer les données durant les phases critiques du développement, surtout celles de la découverte et de l’exploration. La technique est appliquée à des gisements de cheminées diamantifères."

Jan 1, 2015

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By Shanjun Mao

This paper summarizes current achievements of Digital Mining in China, puts forward the concept, framework and key technology of Smarter Mining, and finally points out that there is still a long way to go in order to acheive Smarter mining.

Aug 1, 2013

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By L. Sun

In this work, strontium doped lanthanum ferrite (LSF) and their composite cathodes were fabricated by screen printing on yttria-stabilized zirconia (YSZ) electrolytes. Their electrochemical properties were evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods. All the cathodes were screened by comparing their total polarization resistances before and after activation processes at different temperatures. The improved LSF composite cathodes were also screen-printed on YSZ/NiO half cells to fabricate solid oxide fuel cells (SOFCs), which have reached the output power densities of 170 mW/cm2 at 650 °C, 230 mW/cm2 at 700 °C, 304 mW/cm2 at 750 °C and 388 mW/cm2 at 800 °C.

Jan 1, 2005