Search Documents

By Michel David

"The usual complaint of mines is that grade does not match exploration expectations. Quite often, more tons are mined than expected but at a lower grade. This can be seen as dilution. Geostatistics can help predict which dilution can be expected both in terms of grade and tonnage for different mining methods.The usual vocabulary of geostatistics speaks of block distribution; block variance, size effect, information effect, all terms which say very little to the practitioner. In f act, all this can be rephrased in terms of dilution .In this paper, the following is presented - an example which shows how reserves change with the size of selection units and number of samples taken, and tables which show the dilution that are bound to happen when dealing with the commonly encountered log-normal distribution. Finally, the paper shows how grade tonnage computations should be made in the case of an arbitrary distribution. IntroductionGeostatistics progresses more and more rapidly if one judge s by the number and quality of papers published in Mathematical Geology or at APCOM meetings. More and more case studies describing successful applications are published (David et al., 1986)(Kwa and Mousset-Jones, 1987). It is estimated that more than 270/0 of the gold mines around the world use geostatistics. There is still, however, a lot of resistance from the remaining 73%. Geostatistics has more formulae and equations than it needs to reach year 2000. We will be well into the third millenium before all the models available now are actually used. The progress may come in the form of finding better ways to present known statistical results and getting away from the jargon of geostatisticians. One example may be in trying to explain how we can answer the most common plea of the mining industry: production grade is not what was expected in the feasibility study."

Jan 1, 1988

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By R. Ricketts, D. G. Vanderveer, F. Kirby

"A program of mapping, sampling and testing to determine the potential of the aggregate resources throughout Newfoundland and Labrador was commenced in 1978. A 6-km-wide corridor parallel to all transportation routes was selected as the study area.The study consisted of a preliminary surficial interpretation followed by field mapping and sampling. Granular resources were sampled at a 500-m interval and non-granular materials were sampled at a 1.5- to 2-km interval. Data were gathered on landforms and stratigraphy as well as a field description of the sample and deposit types. Particle-size and lithologic analyses of the samples were also conducted.The locations of samples and deposits were mapped on 1:50,000 topographic base maps and summarized for publication at a 1:250,000 scale. Surficial geology maps were produced at a 1:50,000 scale. A computer program is being developed for the search and retrieval of field data.The first phase of the Inventory of Aggregate Resources program is nearing completion and to date has collected information on approximately 9,500 samples throughout Newfoundland and Labrador. This data will be used to provide f or the effective management of these vital non-renewable aggregate resources.The mineral aggregate industry in Newfoundland and Labrador is very competitive, but undercapitalized when compared to other provinces. The demand for aggregates is forecasted to increase to in excess of23 million tons per annum by the year 2002.In terms of over-all mineral production, the extraction of sand, gravel and stone has a significant impact when compared to other minerals in terms of value and tonnage produced.IntroductionThe province of Newfoundland has approximately 18,000 km of coastline. A large proportion of the population lives in coastal communities where, traditionally, beaches have been a major source of construction materials. Beaches have, therefore, often been subjected to overutilization, resulting in erosion of back beach areas or adjacent headlands."

Jan 1, 1982

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Chris M. Healey

"Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10070 of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By Bryn Harris, Liming Huang, Andre Laplante

"This paper reviews flowsheets generally used in gold rooms to upgrade primary gravity concentrates particularly those of Knelsons. It is concluded that even for small operations, which treat between 250 and lo00 kg of concentrates per day, there is a strong economic incentive to include in the flowsheet magnetic removal of tramp iron, at least two shaking tables, screening of either table feed or table tails at 150-212 um, and scavenging of table tails with a small centrifuge. Headroom, rather than floor space, is often inadequate in most gold room designs, and limits gravity flow and flowsheet flexibility. Experimental data are presented to demonstrate the effectiveness of a small Knelson Concentrator to scavenge significant amounts of gold (up to 91 %) from fine table tails.RésuméCet article examine les schémas d’évolution généralement utilisés pour traiter les concentres gravimétriques d‘or, en particulier ceux produits par concentrateur Knelson. Nous en venons à la conclusion que même pour un petit circuit d’une capacité de 250 A 1000 kg/jour pourrait bénéficier des opérations unitaires suivantes : concentrateur magnétique pour extraire la feraille, au moins deux tables A secousses, criblage de l’alimentation ou du rejet d’une ou des tables i une maille de 150-212 um, et épuisages des rejets fins de table avec un centrifuge de petite capacité. C’est l’espace vertical du lieu où se fait cette concentration qui représente la contrainte la plus importante, plutôt que sa surface, puisqu’il faut maximiser l’écoulement par gravite des pulpes et s’offrir une certaine flexibilité quant à l’agencement final des opérations unitaires. Nous présentons également des données expérimentales pour démontrer l’efficacit6 d‘un Knelson de laboratoire pour récupérer jusqu’ à 91 % de l’or contenu dans les rejets fins de table."

Jan 1, 1999

By F. Hampshire

"IntroductionThis paper is intended to cover questions raised by operating staff at various installations and is not intended to give comprehensive coverage of power plant and power system design. The paper is concerned mainly with the electrics , although a brief section gives the reasons for selection of diesels rather than other prime movers.The material is not new but brings out points which seem to be raised regularly during the design , commissioning and operation o f a new plant. Diesels versus other Prime MoversDiesel-electric plant for the mining industry falls into two major categories -emergency power and prim e power.1) Emergency power (for use only when the regular utility supply has failed) requires reliable starting and operation and reasonable first cost. Fuel economy and maintenance are of little importance as the machine(s) generate few kilowatt hours only. The diesel's competition in this field is the gas turbine, however diesels are more widely used than gas turbines in this application.2) Prime power is a different situation as the bottom line of total cost is highly affected by fuel costs.In general , mines which are within reasonable transmission distance of an existing utility find the lowest net cost result s from hooking up to the utility. If a min e is remote from an electric utility then the possible alternatives are:a) Hydro- electric power if there is a site capable of development at reasonable cost including the cost of transmission facilities. Such sites are not common, but brief and inexpensive considerationof this possibility is warranted .b) Diesel power with consideration of different grades of fuel.c) Thermal (steam) power generation from coal or oil.d) Gas turbines.In addition to the above there is the possibility of wind power (as a supplementary source) and a number of technologies which may become feasible in the future (e.g. small nuclear plants, fuel cells). For obvious reasons, small isolated generating systems required for remote mines, tend to lean to conservative technology.Among the fossil fuel plants, the diesel enjoys advantage on over-all costs as summarized in Table 1."

Jan 1, 1986

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By G. A. Mallory

"The South Bay Division of Selco Mining is located fifty-four miles northeast of Ear Falls Ontario on Confederation Lake. The concentrator operates five days a week and processes six hundred tons per day of copper zinc silver sulphide ore. The concentrator is comprised of crushing, grinding, differential flotation, thickening and drying circuits. The major constituents of the concentrator feed are: chalcopyrite 7%, sphalerite 20%, pyrrhotite 3%, pyrite 25 - 30% and felsitic volcanics 40 - 50%. The mine went into production in March 1971 with an anticipated three year life and is now scheduled for closure in the summer of 1981. Recent mine production has been limited to three cut and fill stopes which have widely varying ore grades, therefore mill feeds vary from 0.25 to 4% copper, 3.5 to 27% zinc, 0 to 0.4% lead and 15 to 30% iron.In mid 1977 Selco negotiated a six month rental purchase agreement with Outokumpu Instruments Canada Limited for a five stream analyser system. The Minexan 202 probes were the first Outokumpu probe type analysers installed in Canada although Outokumpus' Courier systems are well known. Installation of the system took place in April 1978 and after numerous hardware faults the six month evaluation began in August. By December it was obvious that the Minexan 202 probes with proportional detectors did not have adequate resolution to determine low copper values in either of the tailings streams. Outokumpu offered to replace the tailings analysers with a new prototype solid state detector probe the following summer. The evaluation on the five Minexan 202 probes continued until August 1979 when the new solid probe was installed. The Minexan S (solid state) probe was evaluated with the three remaining Minexan 202 probes until December 1979 when Selco elected to purchase the system."

Jan 1, 1981

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d&apos;Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff&apos; divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994