Search Documents

By C. O. Brawner, J. Kalejta II

"The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than approximately 45 degrees.As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result in less rock fall capacity.The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented."

Jan 1, 2002

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By J. M. Carr

The history, geological setting and local geology of the Magnum vein system, 100 miles west of Fort Nelson in northeastern British Columbia, are described. The system comprises a number of quartz-ankerite veins, mineralized with chalcopyrite and lesser pyrite, occurring in a steep northeastly zone of deformation and subsequent dike intrusion within otherwise little-deformed Precambrian sedimentary rocks. In April of 1970, Churchill Copper Corporation began producing copper concentrates in a 750-tpd mill fed from the Magnum mine.

Jan 1, 1971

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By Claude K. Howse

The area covered by the present paper consists of about fifty square miles in the immediate vicinity of the settlement of St. Lawrence, which is on the Southern extremity of the Burin peninsula on the south coast of Newfoundland. Physiography Physiographically, the area is part of the Atlantic upland, equivalent to the New England province of the United States. Evidences of two erosion surfaces are to be seen truncating the intrusives and the folded volcanics and sedimentary rocks. The older erosion surface is represented by small monadnocks from 650 to 750 feet in height with the younger surface covering most of the area and characterized by rounded subdued topography with maximum relief of two to three hundred feet and numerous ponds and bogs. These surfaces have been correlated with the High Valley and the Lawrence peneplains of Newfoundland. On the Avalon peninsula, these peneplains have elevations of, respectively, from 1,300 to 1,700 feet and from 500 to 1,000 feet. Glaciation The entire peninsula has been glaciated, with lee-and-stoss slopes showing on the highest hills in the immediate vicinity, many of which have striae and erratics on their summits. The lee-and-stoss slopes, the glacial striae, and the distribution of certain rocks found in the drift and whose source outcrops are known, indicate a southward direction of ice movement.

Jan 1, 1951

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By T. Junne, L. Eltrop, S. Moreno-Leiva, J. Haas, W. Kracht

The energy systems of the future will be highly renewable. The flexibility that is consequently required can be provided with many options, the main ones being energy storage, transmission reinforcement, and demand side management. The role of the latter is explored for the copper industry, using the scheduling of maintenance services as an example of Solar-Paced Design - the coupling of energy demand with solar resource availability. We used a linear energy optimization model to define the minimum-cost configuration for a fully renewable energy system of a copper concentration plant under different scenarios for the scheduling of maintenance services. For the case we studied, (total) costs were 4% lower when the maintenance was scheduled in winter. We expect that exploring the potential of such Solar-Paced Design in the copper industry will allow new potentials for a more cost-effective full renewable energy supply of this critical industry. INTRODUCTION The mitigation of climate change requires a worldwide transformation of the energy system by the significant expansion of renewable energies and the electrification of various sectors and processes (Teske et al., 2015)(International Energy Agency IEA, 2018). Moreover, considering the decreasing costs of renewable energy technologies and the intensive use required to deliver the goals in the Paris Agreement, we can expect to have highly renewable energy systems in the near future. However, to rebuild and expand our energy systems, we need certain materials, including copper. Also, energy systems based on renewables are more copper-intensive than conventional ones (Kleijn, van der Voet, Kramer, van Oers, & van der Giesen, 2011). The mineral industry, in turn, needs clean energy to achieve a better environmental performance (e.g. solar energy for copper production (Moreno-Leiva et al., 2017)) and to avoid negative secondary effects induced by the strong expansion of clean technologies. But there is something else the minerals industry can offer in this bi-directional relation with energy systems.

Jan 1, 2019

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By Tony B. Szwilski

"The efficiency of operation and life of an advancing longwall coalface depends, to a great extent. on the face-end roof strata conditions and the stability of the gateroads. The factors that influence the rate of closure of gateroads are examined, in particular the gateside pack and the coal rib (crush) pillars. The performance of mechanized packing systems is briefly discussed. Gateroad deformation surveys were carried out at two coal mines to determine the influence of the rib pillar width on gateroad stability; also, the influence of the gateside pack on the immediate roof and floor strata is analyzed based on strata bed displacement measurements from instruments installed in the gateroad and pack-hole of a longwall advancing face operating in a thick seam (7.55 m). Concluding, an evaluation of the fac e-end systems examined is given and recommendations made f or the most suitable rib pillar width. face-end geometry and roof strata reinforcement.IntroductionKevword s: Coal mining, Pillars, Rib pillars, Ground control, Longwall mining, Gateroads , Packing systems, Roof control. The face-end region of a longwall advancing face is the center of mining activity, being the turn-around point for the coal cutting machine. and the place of gateroad formation and movement of special face-end supports. The design of face-end layouts can be aided by knowledge of strata control parameters, such as the effective loading of the immediate roof strata , convergence of the roof and floor, magnitude and distribution of fractures in the roof strata around the face-end , optimum placement of supports, coal seam thickness and strength characteristics, geometry of layout and interaction from neighbouring workings. Generally, the gateroad is formed by one of three face-end methods: (a) advanced headings, (b) in-line system (gateroad formed at the face) or (c) conventional ripping with or without stable elimination (also halfheading). The quality of gateroad is influenced principally by the face-end system employed, standard of gateside pack and width of pillar. A good standard of gateroad is generally achieved by employing the half-heading face-end system, the gateside pack and coal rib pillar having comparative support/ yield (stiffness factor) characteristics. However, the halfheading is often not favoured due to face operation restrictions."

Jan 1, 1981

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011

By J. Ita, F. Malekzadeh

"Multi-scale simulation in coupled fluid flow- geomechanical systems is a computationally efficient method for numerically solving large poroelastic systems. When using multi-scale methods, care must be taken in ensuring consistency when information is exchanged between systems that have a different discretization. Here a method is presented which provides consistency between the pore pressure being calculated on a fine scale fluid flow domain and upscaled to the coarser scale geomechanical domain and the pore volume change being calculated on the coarse geomechanical domain and down-scaled to the fine fluid flow domain. Central to this process is the characterization of the mechanical properties of the poroelastic system at both scales.Another advantage of the method presented here is that it is applicable to hydraulically disconnected but laterally drained (i.e. multi-porosity) layered systems as well as hydraulically connected, layered systems. Thus it can be used in geological situations where thin shale streaks or hardpans impede flow between laterally extensive, hydraulically conductive units. This is significant as the pressure evolution of such a hydraulically disconnected, laterally drained system can be very different than a hydraulically connected one as shown here. INTRODUCTIONA multi-scale treatment of fluid flow and deformation is a key enabler when simulation of poroelastic phenomena is limited by computational resources. As the spatial domain of the geomechanics model is usually larger than the fluid flow model, it is desireable to use a coarser discretization in the geomechanical model compared to the fluid-flow model. This type of multi-scale simulation requires a consistent up-scaling of pore pressure from the fine scale fluid flow model to the coarse scale geomechanical model and down-scaling of pore volume change from the geomechanical model to the fluid flow model (see Figure 1)."

Jan 1, 2015

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By Pingchao Ke, Zhihong Liu

Fe(III)-As(V) precipitates were synthesized from the Fe(II)-As(V)-SO42--H2O system at 90°C in initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The synthesis were carried out by introducing oxygen gas into the system to oxidize Fe(II) ions into Fe (III) ions, and at the same time, adding aqueous sodium carbonate solution into the system to neutralize the acid released by the hydrolysis reactions, with the purpose of keeping the pH constant at 1.5±0.05. The precipitates obtained were characterized by XRD, chemical composition analysis, SEM, XPS, and Raman spectrum. The results indicated that the particles in the precipitates were in the morphology of irregular aggregation with their sizes in the range of about 1–4 µm. The precipitates consisted of scorodite, ferric arsenate and amorphous hydrated ferric oxide, of which amorphous hydrated ferric oxide formulated as Fe(OH)x(SO42-)y. The characteristic XPS peaks of Fe-AsO43- and Fe-O in the precipitates located at 711.8 and 713.3 eV, separately, and the existence of amorphous hydrated ferric oxide led to two series of shake off lines developed over the end of high binding energy of Fe2p XPS. The precipitates were stable in TCLP tests at pH 4.93 for 60 hours with the arsenic concentrations in the leaching solutions being 0.27 mg/L and 0.59 mg/L for the precipitates prepared in the initial Fe(II)/As(V) molar ratios of 4.0 and 5.0, respectively. The tests for the long-term stability of the precipitates were carried out by leaching them for 40 days at 25°C under various media in the pH range from 9.50 to 10.57, and the results showed that the precipitates synthesized in this study were much more stable than those by previous researchers.

Jan 1, 2017

By Michael L. Wayman

Archaeological and ethnographic work during the last century has shown clearly that metals have played a small but important role in prehistoric Arctic cultures. For at least the past several millenia both iron and copper have been used in the North, primarily for blades, projectile points, knives, awls, engraving tools, fishhooks, scrapers and axes. In addition they were used for joining purposes as staples and rivets. It is of great interest to enquire into the origins of these metals. In this connection one begins with the observation that to date there has been no clear evidence for the smelting or melting of metals in the Arctic prior to the arrival of Europeans. This can be explained partly by the absence of traditional pyrotechnologies such as the high-temperature firing of ceramics and the heat treatment of bone and wood. Another factor which surely inhibited the development of smelting/ melting operations is the relative absence of wood in the region. The production of charcoal for smelting requires large quantities of wood, to the extent that the desertification of a number of areas in the Old World is believed by some to have been at least partly caused by charcoal production. In the North this was obviously not possible. Thus the Arctic peoples were restricted to using native (naturally occurring) metals and metals obtained by various direct and indirect forms of contact with areas of the world where smelting was practiced. Both of these sources were important in the case of iron; we know that meteoritic iron, telluric (native) iron and smelted wrought iron were all used in the Arctic. These three types of iron will be considered in tum.

Jan 1, 1999

By J. E. Marshall

"The concept of employing a project management team to coordinate all aspects of the construction of a new resource development has gained wide acceptance. This team can be formed from within the staff of large mining companies or contracted from major engineering firms and consultants. The mandate of the project managers usually terminates on successful startup of the operation. For frontier mineral developments in the Canadian Arctic or in the developing countries, startup and the initial year of operation represents the period in which the project is most vulnerable to technical, political and managerial problems. A complete change of the management team or the retention of the construction project managers and the resulting cost combined with the breakdown of organizational accountability within the operating staff .are unnecessary management problems.Independent project management services provide the commitment necessary to sustain the continuity of management through all project phases. Efficiency and the ability to make decisions quickly are characteristics of the many successful small mining companies. These qualities are necessary in the project management group, which will be responsible for up to 90% of the preproduction costs.Continuous project management in the construction and operational phases of a mineral development are common in the iron ore industry, but remain anomalous in the base metal, energy mineral and industrial mineral fields.The Nanisivik project on Baffin Island in the Canadian Arctic is used to illustrate the advantages of total project management through construction and operation.Total project management has further potential for foreign interests and financial and utility organizations desirous of participating in the Canadian mining industry, but with no direct involvement in the construction or operating management. Participation agreements in the operating phase of a project can be negotiated to have management fees related to both the production and the profits of the enterprise."

Jan 1, 1980

By D. A. Barr

High-grade gold-silver mineralization associated with electrum and argentite was discovered in a quartz vein at the Chappelle property, 273 km north of Smithers, B.C., in 1969 following a regional geochemical reconnaissance program in the Cassiar-Omineca Mountains. Subsequent exploration resulted in the discovery of numerous quartz veins with associated precious-metal values in a belt 17 by 3 km in area centrally located within Toodoggone Group volcanic and sedimentary rocks of Lower to Middle Jurassic age and a window of Takla Group volcanic rocks of Upper Triassic age. More detailed investigations, consisting principally of 5677 m of surface drilling in 57 holes and crosscutting, drifting and raising on Chapelle Vein A, has outlined a high-grade gold-silver-bearing shoot with a strike length of 200 m, an average width of about 3 m and extending to an average depth of about 40 m below surface.

Jan 1, 1978

By G. S. Hume

Research thrives on ideas, and the theoretical considerations of today are either the discarded notions or the proven facts of tomorrow. The progress made in the past fifty years in the acquisition of knowledge of petroleum geology is no less astounding than is the tremendous increase in the production of oil on the North American continent from 61 million barrels in 1897 to 1,917 million barrels in 1947, an increase of 3,300 per cent, with production of natural gas expanding from less than 400,000 Mcf in 1897 to approximately 4,500,000,000 Mcf, or an increase of 11,000 fold in the same period. In the search for and discovery of the oil and gas fields that have yielded such prolific wealth, no idea has had a more profound effect than has the ?anticlinal? theory of oil accumulation, propounded in 1844 by Sir William Logan, the founder of the Geological Survey of Canada, after noting the position of oil seepages on the crests of anticlines in Gaspe peninsula. Sir William apparently was not much impressed with his own idea at this time, but after the Drake well discovery in 1859 and the publication by Henry D. Rogers, of Glasgow University, formerly of the Pennsylvania Geological Survey, of a paper in which he pointed out that the seepages in Pennsylvania were on anticlines, T. Sterry Hunt, an associate of Sir William Logan on the Geological Survey of Canada, published a reasonably comprehensive statement of the anticlina theory in the Montreal Gazette on March 1st, 1861. Hunt recognized the fact that the oil ?being lighter than the water which everywhere penetrates the rocks below the water level, naturally rises and accumulates along the crown of these anticlines". This was a recognition of the fact that gas, oil, and water in an anticlinal structure separate according to buoyancy or specific gravity. For some years the anticlinal theory does not seem to have attracted much attention, but when I. C. White in 1883 revived it and put it to practical use by prospecting for 'anticlinal' oil an gas structures in Pennsylvania, West Virginia, and Kentucky, its real value not as a theory but as a fact became widely recognized. Even today, the search for anticlines as oil and gas structures is being vigorously continued. In the past fifty years, however, it has become widely recognized that petroleum and natural gas collect in many different types of structures, and these have become known by the general name of 'traps'. About 1890, terrace structures were highly regarded because it was thought certain oil fields in Pennsylvania, New York, and Ohio were directly related to them. However, as Wilson (2, p. 437) has pointed out, it is recognized to day that ?'wherever the surface evidence is complete and dependable, other factors (than the terrace structure) are found to be in control'.

Jan 1, 1948

By Balmer Neilly

Early in my term of office it was announced that my Presidential Address would make particular reference to the subject of Mine Taxation in Canada. With this purpose in view there was drafted a Balance Sheet and Earnings' Statement of a Gold Mining Company. This in turn was submitted to the Dominion Income Tax Authorities in Ottawa and to the Minister of. Mines of each of the several Provinces of Canada. The response to the invitation was not as complete as we had hoped it would be, but the figures that were obtained will be presented during the present meeting, and they constitute, I hope, a sufficient basis for extended study and additional enquiry during the year to come ( 1) . In the form letter that accompanied our request to have the submitted earnings assessed, I made the following assertion: "In this work we have three objects in mind. 1.--We will get direct comparison between the different Provinces in Canada. 2.-We will in this way educate our members concerning taxation as it affects the mining industry. 3.-We will publish the details as to how the assessment is calculated by each body, so that a Mine Manager in the most remote district will have a ready reference to guide him in his annual return to the taxing bodies. As things stand, there is no intention of making this a basis for a critical attack on the present rates assessed. It is intended as an authoritative summary of actual conditions as they presently exist".

Jan 1, 1934