Search Documents

By K. Karan

Oxygen reduction reaction in PEM fuel cell cathodes involves participation of three reactants - oxygen, hydrogen ions, and electrons. Electrochemical reaction in the catalyst layer is, therefore, influenced by how these species are transported to the reaction site. The two-phase boundary locations at which percolating networks of ionically conducting electrolyte and electronically conducting Pt/C meet are feasible reaction sites. The electrolyte phase also provides pathway for the transport of dissolved oxygen. Most of the 3-D models describe the catalyst layer as an ultra-thin layer, thereby, losing useful information on the distribution of electrochemical reaction rate. In this paper, we extend our previous work on 2-D cross-the-channel modeling of PEMFC cathode based on agglomerate catalyst layer. In particular, we take a closer look at the influence of proton conductivity on the reaction rate distribution in the catalyst layer. As well, we re-examine the role of anisotropic transport coefficient of the porous transport layer (PTL), commonly known as the gas diffusion layer, on the current density distribution under the channel and the rib of the flow-field plates. Results from both a 2¬D and a 3-D models will be presented.

Jan 1, 2005

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By S. Kwon, J. W. Wilson

"In salt and potash mines, the time-dependent deformation mechanism should be clearly understood based on in situ measurements to predict the performance of a mining design. In this study, in situ deformation measurements from the Waste Isolation Pilot Plant (WIPP) and other salt and potash mines were used to determine the transition time from the primary to the secondary creep stage and to investigate the influence of adjacent excavations such as a nearby tunnel excavation, panel excavation and/or pillar extraction on rock deformation. IntroductionThe deformational behaviour of underground excavations in salt and potash mines is complex due to the time-dependency of the rocks. When the material properties are determined from laboratory tests, they should be carefully applied to in situ conditions, because in situ conditions are completely different from laboratory conditions. For instance, in situ deformation measurements show that the deformation rate decreases with time similar to those observed in the laboratory during the early stages. However, the rapid decrease of deformation rate does not come from the microscopic strain hardening effect observed in laboratory tests, but mainly from stress relief around the opening after its excavation (Baar, 1977). It is, therefore, recommended to undertake in situ measurements and use them to understand the deformation mechanism.Even though in situ measurements are widely accepted as important information for understanding the deformation mechanism of salt and potash (Barr, 1971; Kovari and Amstad, 1993), not many publications have focused on the fundamentals of data measurement, the application of the measured data, and the development of data analysis techniques. Recently, several new techniques for better understanding the deformation mechanism of rock salt have been developed that are based on in situ measurements. Kwon and Miller (1995) developed a new technique for describing the actual deformational behaviour of an underground excavation in rock salt. The migration of “zero strain boundary,” which represents a no movement boundary around an underground excavation, could be calculated by the technique developed by Kwon and Miller (1996). Kwon and Wilson (1997, 1998) applied neural network techniques to in situ deformation measurements to predict the deformational behaviour of the underground excavations at the Waste Isolation Pilot Plant (WIPP) located in the United States.In this study, in situ deformation measurementsfrom the WIPP site and other salt and potash mines in the United States were extensively analyzed to understand the deformation mechanism of the underground excavations in the rock mass."

Jan 1, 2002

By D. C. Martin, P. M. Hawley, C. P. Acott

"In bedded deposits such as coal or sedimentary iron, economic limits of mineable reserves are clearly defined by the footwall of the seams or ore-bearing units. Where open pits are developed in dipping strata, a long, high footwall slope may result. In many cases, unbenched slopes excavated along the base of the lowest mineable seam are operationally simple, economically desirable and geotechnicalty practical, although a variety of failure mechanisms may develop. This paper examines the engineering geology and rock mechanics parameters of importance in the design of footwall slopes. Possible failure mechanisms and stability analysis methods are described. Design considerations for benched and unbenched slopes are discussed with prime consideration given to development of long high stopes without benches or with a minimum number of benches. IntroductionIn bedded deposits, the ultimate depth and economic viability of an open pit in dipping strata may be controlled by the design of the footwall slope. The stability and, hence, design of footwall slopes is strongly influenced by the engineering geology and rock mechanics parameters of the slope forming materials. A clear understanding of the structural geology, engineering geology and tectonic history of the deposit is essential to assess the behaviour of the slope. This is particularly important for long high, unbenched footwall slopes such as shown in Photo I.A rational footwall slope design requires identification and assessment of all possible slope failure mechanisms with respect to the proposed slope geometry. Stability analyses of each potential failure mechanism are used to identify the main controls on slope stability and to develop appropriate slope design criteria. The optimum slope design is based on the most economic and geotechnically practical slope geometry with due consideration of operational constraints and of the possible advantages of specific remedial measures."

Jan 1, 1986

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By R. O. Grieve

"IntroductionCALEY (1945) and Evans (1950) pointed out that certain instances of convergence between Devonian and Silurian horizons, frequently evident in wells drilled for oil and gas in Ontario, appear to be related to local thinning of salt beds in the Salina formation and they suggested that leaching of the salt beds may have occurred. Exploratory drilling by Imperial Oil Limited since 1945 has brought to light several examples of structures similar to those discussed by Caley and Evans. The writer has had the opportunity to examine cuttings and data from wells which penetrated these structures and the attempt to interpret them in the light of the theory of leaching and subsidence proposed by Landes ( 1945a) to explain the marked brecciation and deformation of Upper Silurian and Middle Devonian sediments which crop out in the Mackinac Straits region of northern Michigan has led to the observations presented in this paper."

Jan 1, 1955

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By Sabry A. Sabour

Metal price is among the key variables in the open pit optimization and the economic evaluation process. The common approach to handle metal prices in open pit mine planning is to optimize the ultimate pit and the mining schedules using a fixed, flat metal price. In this respect, metal price is assumed to be known with certainty throughout the entire mine life, which in some cases can reach 80 years. Given the volatile nature of metal markets and the metal price cycles, the conventional pit optimization approach may generate sub-optimized mining plans, which results in either extra costs to mining projects or lost revenues, or both. Long-term operational decisions such as future pit expansions, beyond the currently optimized limits, cannot be handled using the pit optimization approach based on flat metal prices. There is a growing interest in the mining industry to model and manage such market uncertainty in the pit optimization as well as the project evaluations in order to maximize the value of mining operations. In this paper, the author will outline a practical approach to optimize the ultimate pit taking into account the volatility and variability of metal markets. The proposed approach uses a combination of the pit optimizer of the commercial MineSight package and a simulation-based economic modeling real options valuation approach employing the least-squares Monte Carlo algorithm. MineSight pit optimizer employs both the floating cone for initial optimization exercise and the standard Lerchs-Grossmann algorithm. In this paper, Lerchs-Grossmann option will be used to generate the pit shells. Real options valuation approach used in this study is based on generating multiple metal price scenarios. Metal price uncertainty is modeled using stochastic metal price models such as the geometric Brownian motion and the mean-reverting process. The mining operational scenarios corresponding to the simulated metal prices are then optimized using the least-square Monte Carlo approach. The objective is to maximize the discounted cash flow value of the project while incorporating the operating flexibility to revise the operating status of the open pit with time as new information becomes available. The focus of this work is on the practicality of the proposed uncertainty-based pit optimization approach and the difference it can make to the technical operational mining decisions. A case study of a hypothetical open pit poly-metallic mine is provided. The deposit contains copper, gold and silver grades. The run of mine ore is sent to the process plant that produces copper concentrate with copper as the main metal and gold and silver as the by-products. Four uncertain variables are considered here include copper, gold, silver prices and foreign exchange rate. Both copper price and exchange rate are modeled using the mean-reverting process while gold and silver prices are modeled using the geometric Brownian motion. The case study is performed using both the conventional flat price pit optimization approach and the proposed uncertainty-based one to compare results.

Aug 1, 2013

By S. N. Bhatnagar, S. K. Haldar

"Mineral exploration is an expensive speculative venture and calls for optimization of sampling. Exploration is generally planned in grid pattern to be conducted in phased manner. The objective of any such campaign is to assess the quality, quantity and its reliability. The traditional estimation methods are unable to provide a means of calculating the degree of reliability. Application of mathematical models can quantify the precision of estimation and bring forth decision-making criteria at any stage.In this paper three statistical and geostatistical models, viz., Frequency, Probability, and Semi-variogram, have been employed to evaluate sequential exploration data of RampuraAgucha zinc-lead deposit. The optimization in exploration for a specific objective has been highlighted.IntroductionAny exploration campaign demands heavy resource investment starting from the collection of the first sample to the production of the first ton of ore. The best estimation would be if the entire orebody is taken out and sampled. However, this is neither possible, nor desirable. Drilling is the primary tool of geological sampling. It shares the major portion of the investment and, thereby, warrants critical analysis at every stage during the ongoing exploration projects.The exploration program should be conducted as a well planned scheme based on a sequential evaluation approach in a phased way to achieve a specific objective. It would then be possible to evaluate exploration data at the completion of each phase by employing computer-based mathematical techniques to quantify the precision of the estimate for fulfillment of objectives. The subsequent drilling program should be modified accordingly."

Jan 1, 1987

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984

By E. H. Rose

THE most useful guide to the role of lime in flotation is the view that the chemistry of any flotation operation is primarily a pattern in relative solubilities. We have the coming together of a number of minerals, reagents, fortuitous salts, water, and oxygen, many of which have not been previously in contact with each other, and every one of which is free, at least to some extent, to abandon old alliances and to form new ones. Of one thing the operator may be sure, and that is that, when equilibrium has been reached, those new chemical combinations will have formed which are the least soluble combinations possible to the environment. The laws of solution govern the operation, which means that relative concentrations are always a factor, and temperature frequently is. What the operator is really doing when he chooses his reagents .in the first place (empirically or otherwise) and works out their? optimum amounts, is to provide an environment in which (1) the least soluble possible compound of the mineral he desires to float is one which is also non-wettable, while at the same time (2) the least soluble compounds possible to the minerals he desires to depress are wettable. Since all metathesis is reversible, perfection is impossible to achieve, and the operator is constantly striving to establish that combination of concentrations which will drive each and every particular reaction as far as possible in the direction he desires it to go, in accordance with the law of molar concentration.

Jan 1, 1939

By G. T. Lapidus, A. Garcés, O. J. Restrepo

"Colombian nickel laterites have historically been processed by pyrometallurgy. However, due to the depletion in ore grades, alternative processes are required. Hydrometallurgical processes, such as pressure acid leaching, have been proposed as alternatives to extract nickel from deposits with suitable characteristics. Such a leaching process requires high concentrations of acid to achieve acceptable extractions, and is not selective. In this study, an alternative aqueous alkaline glycine system has been employed to evaluate the leaching behaviour of a Colombian nickel laterite which contains 1.15% Ni, 0.12% Co and 41.1% Fe. Additionally, the effect of the addition of chloride ions, the use of a reducing agent and the application of a pre-treatment to improve the extraction of nickel were evaluated. Extractions of 4.63% Ni, 42.16% Co and 0.33% Fe were obtained using a 1M solution of glycine at pH 9. In addition, an increase in nickel extraction from 4.63% to 25.68% was achieved by applying a pre-treatment to the sample. The results show that even though nickel dissolution was much slower than in acid leaching, it was selective over other metals such as iron, proving the proposed method to have potential as a process for the extraction of nickel from Colombian laterites.INTRODUCTION Before 2010, most of the industrial operations used pyrometallurgical processes for the extraction of nickel, mainly in saprolitic regions of deposits, with greater contents of the metal. Nevertheless, due to the gradual depletion of such deposits, different hydrometallurgical processes have been studied as alternatives to process those nickel laterites with low grade and those which present problems of refractoriness due to the presence of acid consuming materials (McDonald & Whittington, 2008; Oxley & Barcza, 2013; Wang et al., 2012). However, such leaching processes require high concentrations of acid to achieve acceptable extractions and they are not selective. Facing lateritic nickel ore deposits containing high levels of acid consuming materials, an alkaline leaching medium becomes an advantageous alternative over acidic media, due to the increase in selectivity and decreased corrosiveness and reagent consumption (Tanda, Eksteen, & Oraby, 2017). Unlike conventional acidic reagents used for metal recovery, alkaline reagents can selectively dissolve the desired metal, leaving in the solid residue other elements such as iron, magnesium and aluminum, which are problematic in subsequent stages of metals separation and recovery. Furthermore, there are no serious corrosion problems associated with alkaline leaching, even at higher reagent concentrations, or at elevated temperature and pressure (Ntumba Malenga, Mulaba-Bafubiandi, & Nheta, 2015)."

Jan 1, 2017

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007