Search Documents

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen's University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. 's H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

By R. S. Fitzpatrick, P. Hegarty

"Gravity separation is a key technology in the recovery of a range of mineral ores including coal, tin, tungsten and tantalum. One of the problems associated with gravity concentration is that recovery is traditionally lower than for other separation techniques such as the flotation of base metals. Any improvements in recovery will, therefore, have a significant effect on the economics of operations of this type. More accurate, robust modelling of gravity separators is one means of achieving greater recoveries. Furthermore, better modelling can lead to more informed equipment selection and process design for potential economic deposits.Previous models for gravity separation equipment have typically relied on simple metal mass balances from samples of the separated products. However, with advances in technology there is a ready availability of analytical instruments for the automated quantitative determination of mineralogy. Instruments such as the Mineral Liberation Analyser and QEMSCAN make it possible to estimate particle size and density (related to mineral liberation and association) which are the primary factors in gravity separation. Models produced using quantitative mineralogy of feed streams will be potentially superior to those produced historically.This paper describes test work undertaken on a wet shaking table using a synthetic ore. The objective of this test work was to develop a model to predict the effect of changes in feed ore characteristics on shaking table performance by measuring quantitatively the mineralogy of the feed material. Particles were divided into size/density classes based on the results of QEMSCAN analyses.It was found that it was possible to use data from QEMSCAN to predict the recovery of size/density classes and to predict the effect of changes in the relative abundances of these classes on the separation. This model can potentially be used to adjust operating variables to maximise grade and recovery by monitoring the input feed. Care was needed when utilising QEMSCAN data to ensure representivity."

Jan 1, 2016

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By J. M. Paxton, R. L. Roscoe, G. A. McCreary, W. W. Muir, T. J. Drown, D. A. Barr, T. W. Law

"This paper reviews the complete cycle of a small mining operation in a remote section of northern British Columbia, including discovery, exploration, development and production. The discovery of high-grade epithermal gold-silver mineralization occurred in 1969 following a regional geochemical reconnaissance program designed to search for porphyry copper mineralization in the Cassiar-Omineca Mountains. Exploration and development from 1971 to 1979 included geological, geochemical and geophysical surveys; trenching, almost 30 000 feet of surface and underground drilling in about 100 holes and cross-cutting, drifting and raising on the principal goldsilver- bearing vein. This led to the delineation of 100000 tons at an estimated grade of0.9 oz gold per ton and 18 oz silver per [on to an average depth of 120 feet below surface. of a 100-ton per day mining operation employing about 50 personnel with all supporting infrastructure transported to the site by a Hercules aircraft. The operation was subsequently supported by its own Twin Otter aircraft with periodic Hercules campaigns supplying major items including fuel.The mining operation included both open-pit and cut-and-fill methods. The milling operation employed conventional cyanide leach process with cyanide destruction initially by alkali chlorination and subsequently by the Inco SOl /Air process.The fly-in operation, initially structured on a 21-day-in and 7-day-out basis was modified to al-t-day-in and Z-day-out basis with no loss in efficiency and with a significant increase in employee satisfaction. The operation, which earned the B.C. Small Mines Safety A ward in two consecutive years in its Ll-month operating history, emphasized safety and process hazard awareness. Wildlife studies in the environmentally sensitive mine area also showed that industry and wildlife can coexist in harmony.Most importantly, the paper compares the feasibility assumptions with actual operating experience."

Jan 1, 1986

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By Will Callupe Arzapalo

The success of the minimization of blast induced-damage at Barrick?s Pierina Mine in Peru is the result of an effective working relationship between Mine Operations and the Geotechnical Services Department. A detailed design criteria manual is used to match the blast plan to the site?s varying rock types and slope designs. The Geotechnical Services Department has further developed a comprehensive pre- and post-blast checklist that is critical to the drilling and blasting process as it pertains to wall stability. Wall control blasts are evaluated with quality assurance field checks, vibration monitoring and frequency control, video assisted performance quantification and post excavation face profiling. These detailed observations are compiled and summarized in a blast performance evaluation that is considered to be an ?Industry Best Practice?. The information and detail provided by each performance summary allows accurate blast analysis and effective design refinement.

May 1, 2006

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By Grant D. Nicholas

This paper compares an integrated evaluation approach to decision-making with more traditional sensitivity analysis and Monte Carlo simulation. The primary objective is to highlight the differences in NPV that can arise from using these evaluation methods in a top down and bottom-up approach. Results from three resource scenarios, derived from sampling a "virtual" ore body (reality) on grid spacings of 75m, 50m and 25m, are analyzed and compared.

May 1, 2007

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By M. Gangal, M. Grenier, D. Mchaina, S. Hardcastle

"Exposure to airborne respirable silica in surface and underground mine operations is known to be the cause of industrial lung diseases. For this reason, silica is a regulated substance and worker exposure must be monitored regularly. Diesel exhaust also contains substances which are potential caricinogens. In an underground setting, diesel particulate may be the main component of what is referred to as respirable combustible dust (ReD). Although diesel particulate or soot is not at present a rigorously regulated substance, new epidemiological data is prompting North American institutes and agencies to regulate diesel soot or RCD exposure. This paper describes a method where by silicaand RCD exposure may be determined using a single personal sample. In this method, an airborne respirable dust sample is obtained and analyzed nondestructively for silica components using an on-filter X-ray diffraction method. Filters are then ashed at 500°C in a muffle furnace over a four-hour period to determine mass loss due to RCD burning. Using on-filter X-ray diffraction analysis as opposed to redeposition of dust samples onto another analytical substrate allows the"

Jan 1, 1992

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By S. Jayasekera, A. M. T. S. Bandara, J. Kyle, E. Koenigsberger, L. Koenigsberger

The extraction of rare earth oxides from fluoroapatite rich phosphate concentrates often involves a weak acid leach of fluoroapatite and a sulphuric acid bake of the leach residue followed by water leach and precipitation to obtain an intermediate product. The main aim of this study was to determine and rationalize the solubility of rare earth metal ions in synthetic solutions representing various process liquors at the temperatures 40, 60 and 80oC. The liquors contained different acid and metal ion concentrations with respect to sulphuric acid, phosphoric acid and sulphate salts of sodium, magnesium, aluminium, potassium, calcium and iron(III). A solid of mixed rare earth carbonates was used as the source of rare earth metal ions. The solubility tests and characterization of solids using XRD were conducted at Murdoch University laboratories as part of the process development for the Arafura Resources Nolans rare earth project. The composition of initial carbonate solids and the solids and solutions formed after saturation were analysed for rare earth and other elements at TSW Analytical Laboratories in Perth using ICP-MS and ICP-OES. The precipitated solid in sodium-rich acidic sulphate solutions is the double salt NaRE(SO4)2 based on the solid assays. However, in acidic solutions free of sodium or of low concentrations of sodium the precipitated solid appears to be RE2(SO4)3.

Jan 1, 2014

By W. A. Plachner, Schiller E. A., S. P. Santiago

"The Monkman Coal Property is located in the Northeast Coal Block of British Columbia. It is divided into the Duke Mountain Block on the north east and the Dip Slope on the west. Together, these areas cover 39,503 ha of coal licences.The property is underlain by Jurassic and Lower Cretaceous marine and continental sedimentary rocks. Economic coal measures are contained within the Gates Formation. Exploration of the property began in the early I970s, with drilling commencing in 1975. To date, 255 holes have been drilled and nine adits have been driven to recover unoxidized coal samples.The property has a geological resource potential of 2.8 billion tonnes of medium and high-volatile bituminous coal. Medium-volatile bituminous reserves, totalling 68.9 million ROM tonnes at an over-all strip ratio of 6.3:1, have been identified in three pit areas in the Duke Mountain Block.Construction start-up will commence when sales contracts are arranged. The clean coal will be exported via the Ridley Island Terminal at Prince Rupert.IntroductionThe Monkman Coal Property is located in the Northeast Coal Block of British Columbia in the southern port ion of the Peace River Coalfield. The coal field encompasses a strike length of 250 km of Lower Cretaceous coal-bearing strata in which 13 companies have identified several billion tonnes of resources and several hundred million tonnes of reserves. Currently, two companies with contracts are in the construction phase, and are scheduled to produce coal by early 1984. Quintette Coal Ltd. has a contract with Japanese steel mills to supply annually 5.0 million tonnes of metallurgical and 1.5 million tonnes of thermal coal. Teck Corporation (Bullmoose property) has a contract to supply 1.7 million tonnes of metallurgical coal annually."

Jan 1, 1983

By A. McLean, J. Hou

Waste slag is a major environmental concern within the metallurgical industry. In the steel industry, about 100 kg of slag is produced in making one tonne of liquid steel from iron in addition to that produced during ironmaking. The amount of slag from the steelmaking converter can be significantly reduced when charging hot metal with low phosphorus and sulphur contents. In this context, hot metal pretreatment is known as an effective means of preparing high quality charge material for the converter thus limiting the generation of residual slag during the steelmaking process. In the aluminum industry, about 2-4 tonnes of slag, including red mud from alumina production and dross from aluminum electrolysis and casting, are generated during the production of one tonne of aluminum. In recent years, reuse of waste slag from the aluminum industry is a topic that is receiving increasing attention. In this paper, the possibilities of using waste slag and by-products from the aluminum industry as a refining flux in the steel industry are discussed. Several successful processes to convert waste materials from the aluminum industry to steel refining fluxes are described. Some theoretical aspects of using calcium aluminate based flux for desulphurization are outlined together with results obtained from laboratory experiments on sulphur removal from hot metal. By intelligent use of waste materials, the disposal of solid waste from the metallurgical industries can be reduced.

Jan 1, 2004