Search Documents

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By Manqiu Xu, Glen Robertson, Steve Wilson, Pete Quinn

"The middlings circuit, once called the pyrrhotite rejection circuit, at Inco’s Clarabelle mill was a single flotation stage. It used to process a combined feed consisting of the main flotation scavenger concentrate and the non-magnetic portion of the magnetics flotation circuit tails. The typical circuit metallurgy was 55% nickel recovery at 6.5% Cu+Ni concentrate grade. In the past few years, a research project with the objective of improving the circuit metallurgy was initiated between Inco’s research laboratory and the Mill’s Process Technology group. This project has gone through three steps: a) initial laboratory studies, b) on-site pilot plant investigation, and finally c) full plant implementation.The present paper describes the initial laboratory test work. The development of a two-stage circuit consisting of separate rock and pyrrhotite rejection stages to replace the simultaneous rejection of both rock and pyrrhotite in a single stage is discussed. A two-stage circuit simulation based on batch laboratory flotation data is also presented. Further development work, including the on-site pilot plant test work and the plant implementation of the new circuit design, will be described in a later publication.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill, Copper Cliff, Ontario processes a rich complex sulfide ore from several large production mines around the Sudbury basin (Agar, 199 1). The sulfide mineralization is simple, consisting of chalcopyrite (Cp), pentlandite (Pn) and pyrrhotite (Po). The main gangue minerals are pyroxene, feldspar and quartz with minor amphibole and talc. Estimates of mineral composition are routinely calculated from Cu, Ni and S assays. In the mineralogical calculations, all gangue minerals are conveniently grouped and treated as rock (Rk)."

Jan 1, 2000

By Michael G. Nelson

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modelling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing, allowing optimization of the mill processes on an almost realtime basis. This is not happening because mill feed it is often treated as a uniform material, when in reality it varies in composition and characteristics. The University of Utah is investigating the use of odor sensors for maintaining traceability in ore production and processing. Odor sensors now used in food processing, environmental monitoring, and other applications can detect the presence of very small amounts (0.1 - 500 ppm) of some molecules. An assortment of such molecules could be used to ?tag? blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ?electronic noses? could be used to assess its characteristics in real time.

May 1, 2004

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By V. Concha, M. Hashemzadeh

"The objective of this study was to gain a better insight into the kinetics of chalcocite leaching in an acidic ferric sulfate media. Chalcocite leaching in acidic media is known to occur in two sequential stages, with the first stage being much faster than the second. The leaching residue from the first stage is typically assumed to be a covellite type of material. This study hypothesized that the mineralogy after the first-stage leaching varies in response to different leaching conditions. We investigated the dependency of the mineralogy of the first-stage leaching residue on temperature and initial ferric concentration. The experimental results showed that chalcocite leaching behavior altered upon temperature and initial ferric concentration. A proposed combined reaction model was found to be able to describe the experimental data. The first stage was described very well by the shrinking core diffusion model while the second stage was described very well by the shrinking core chemical reaction model. This finding has important implications for mine operations to manipulate leaching conditions to create the desirable leaching kinetics.INTRODUCTION The kinetics of chalcocite leaching in sulfate media has been extensively studied (Cheng & Lawson, 1991; Fisher, 1994; Fisher, Flores, & Henderson, 1992; Niu, Ruan, Tan, Jia, & Sun, 2015). Sullivan (John D. Sullivan, 1930) proposed a two-stage process for chalcocite leaching in an acidified ferric sulphate solution. The two-stage leaching of chalcocite is presented as the following reactions:"

Jan 1, 2017

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By G. R. Parslow

U, Fe, Mn, Ni, Cu, Zn and Co data for the sediment in both Key and Seahorse lakes, which overlie portions of known economic uranium deposits in the region, are presented. With the exception of U, Fe and Mn, the elemental distributions can be considered anomalous, in a statistical sense, in both lakes. The U values are of particular interest in that Key Lake is not anomalous, whereas Seahorse Lake is markedly anomalous. Tentative correlations made with background data from other surveys in an attempt to differentiate between anomalous and background values indicate that deviations from linearity in a distribution, and not absolute mean or maximum values, are indicative of anomalous samples within the distribution.

Jan 1, 1979

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By M. Beech-Jones

The increased emphasis on the efficient utilization of capital and mineral resources has led to several new advances in the science of mineral separation. One example of a recent development is the application of high-capacity high-intensity wet magnetic separators to fine hematit e recovery by a leading Canadian iron ore producer. The iron ore recovery feasibilit , flow-sheet development, circuit operation and metallurgical performance are reviewed.

Jan 1, 1979

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By Nichols. R. S.

"Surface coal mining production from Elk Valley and area in southeastern British Columbia began in 1913. Since 1970, five open-pit mines have been put into production: Westar Mining&apos;s Hanner and Greenhills Operations; Fording Coal&apos;s Fording River Operation; Byron Creek Collieries&apos; Coal Mountain Mine and Crows Nest Resources&apos; Line Creek Operation.ln 1983 these mines produced 14.9 million tonnes of raw coal at an average strip ratio of 4.9 bank cubic metres of waste to 1.0 tonne of raw coal. This is 70% of the estimated 21.1 M tonnes annual capacity .Multiple seams are recovered with truck/shovel and dragline equipment. There is a wide range of equipment types in use with a recent trend toward larger and more mobile equipment.Coal mining in Elk Valley involves advancing along strike in four steps: hangingwall waste removal; seam cleaning; coal recovery; and foot wall waste removal. Each mine is unique in its approach to these four steps but the truck/shovel methods can be categorized into three main groups: seam dips < 35 degrees as at Harmer, Fording and Greenhills; seam dips 35 to 50 degrees as at Line Creek; and seam dips >50 degrees as at Byron Creek. Dragline mining at Fording involves bath waste and coal removal by draglines."

Jan 1, 1984

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper&apos; the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020