Search Documents

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By K. V. Konigsmann

"The results of Mr. Klymowsky's research confirm the essential role played by oxidation products in the flotation of base metal sulphides. They invite a discussion on the subject of aeration which I may open by a brief description of the development and current practice of aeration. The first installation of pre-flotation aeration in Canadian milling practice was undertaken during the years 1928 and 29 at the then new Noranda Mill. C.G. McLachlan and his collaborators demonstrated that the flotation differential between chalcopyrite and iron sulphides was enhanced by aeration in soda ash alkaline pulps. The ores treated contained more than 80 per cent sulphides. It was proposed already then that the products of mineral oxidation assisted copper and retarded iron sulphides, at least pyrrhotite flotation. The concentration of thiosulphates was used as a measure of the progress of oxidation. Several papers by C.G. McLachlan elaborate on this subject.The aerator was also used as classifier since it was held that aeration, i.e. controlled oxidation, should go hand in hand with creation of new mineral surfaces. Grinding mills and aerators were placed in closed circuit. Figure 1. This aeration was essential for successful separation at Noranda.Following the application of aeration at Noranda the technique was applied to existing mills in N.W. Quebec. Impressive improvements in concentrate grades and recoveries were obtained. It was observedthat the zinc flotation benefitted from aeration as much as the preceding copper float. In the late forties and fifties the aerator classifier was installed in new mills associated with the Noranda group. A diagrammatic sketch of the Quemont flow-sheet (figure 2) may serve as a typical example."

Jan 1, 1973

By Haibin Wang, Zhiwei Huang, Zhixiang Cui, Wenzhao Cui, Zhi Wang

Fangyuan Two-Step copper smelting process was commercialized in October, 2015 and has been operating for 3 years and 5 months. As the unique continuous copper smelting process with simplified flow in the world, production parameters have been significantly improved after three years. In the first half of 2018, the feed rate was above 200t/h, availability reached 97.5%, operation cost was about 20% lower than the conventional three-step processes showing obvious economic advantages. The Two-Step process in Fangyuan is composed of 1 Submerged Lance Smelting furnace (SLS) and 2 Submerged Lance Converting& Refining furnaces (SLCR). Two SLCRs work alternatively to ensure continuous production. High grade and liquid matte from the SLS is introduced to the SLCR by sealed launder to complete converting and refining. The SLCR is an original and independent innovation of Fangyuan, for which Fangyuan completed lots of development and improvement. This paper will introduce the process and experience. INTRODUCTION China is the largest producer and consumer of refined copper. Most of the processes adopted in China are conventional "Three-Step" copper smelting processes, which are comprised of smelting, converting and refining. There exists some problems in the conventional processes, such as high energy consumption, large heat loss, low altitude emission of SO2, etc. To deal with these problems, Fangyuan developed the new copper smelting process with simplified flow, low cost, clean and high efficiency. The SLCR that combines converting and the refining process was also developed, which shortens the process flow from conventional three steps to two steps. The SLCR is of great significance in promoting the development of the copper industry. Development and industrialization of SLCR At present, copper concentrates are treated in three steps: smelting, converting and refining. Anodes are also produced by continuous converting processes such as the Mitsubishi process and the Double Flash process. Problems like matte transportation by ladle, capacity limitation, and low altitude pollution exist.

Jan 1, 2019

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By Baoquan An

The energy required to fragment a rock is proportional to the increase in the fracture surface area and hence is proportional to the rock?s surface area. In comminution, the slope of the linear relationship between size reduction ratio and specific energy is usually defined as grindability. Another definition of grindability based on newly created specific surface area and specific energy is introduced. The two definitions for grindability reflect the grindability properties of rocks and can be used to measure of the efficiency of mills or crushers. The feed particle size distribution influences the energy needed to comminute the rock. For a given ratio of average feed size to product size, the smaller feed size requires more energy.

May 1, 2004

By Simon Houlding

"The objective of Part J of this paper is to identify the limitations of the traditional modelling methods and to illustrate, by example, the potential for error created by their application to complex deposits and mining situations. Part 2 describes the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods.The Case for Precision ModellingIt is not the intent of this paper to promote the benefits of computer modelling per se. It is assumed that these are recognized by the mining industry in general. The concern of Part 1 is to identify, qualify and quantify (where possible) the limitations of the tractitional modelling methods. In many instances these methods continue to be applied to complex geological and mining situations for which they were never intended nor designed. The source and magnitude of the resulting errors, conflicts and inefficiencies are not always obvious, however, they can have far-reaching effects on the efficiency and profitability of mining operations.The conclusions support a rapidly growing demand by industry for practical, precise modelling technology which eliminates the deficiencies and can be applied with confidence to evaluation, design, planning and control of mine production in all situations. Part 2 describes new technology which has evolved in response to these industry pressures and has already been successfully applied to complex mining situations. This new technology can aptly be described as appropriate technology for the 1990s."

Jan 1, 1991

By R. W. Zeindler, D. A. Fawcett

"A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxiliary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till.Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the crosspit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/ cross-pit conveyor system."

Jan 1, 1981

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011

WHAT IF? ?Mine closure and reclamation liabilities were fully funded -at all times from current mine revenues ?Unexpected & catastrophic events were insured ?Remediation costs could be capped ?Risk management was improved ?best practice and independent oversight ?Host communities?concerns were adequately addressed If this could be achieved within a cost-effective financial structure, this may be a solution to a complex issue for the mining industry

May 1, 2006

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By J. G. Cullain

In conjunction with the over-all goals of energy conservation at Inco Metals Company, a program of improvement in compressed air utilization was established. Air flows were monitored and compared to calculated requirements to establish efficiency by area. With the cooperation of area management, measures were implemented to reduce nonproductive usage. At the operation, annual savings in power consumption alone were 80,000 dollars. The program is being extended to other mine areas within the Division.

Jan 1, 1979

By A. S. Dawson

"IntroductionTHE PURPOSE of this paper is to describe the results of a preliminary investigation of a method thought to be useful in interpreting geological structures in un-metamorphosed sedimentary rocks. The writer is not aware of the method having been described or investigated previously, although no thorough search of the literature has been made.The method to •be described is based on the assumption that, in argillaceous sedimentary rocks, certain ceramic properties are diagnostic for certain beds within areas of variable limits.Two ceramic properties• have been investigated: pyrometric cone equivalent (P.C.E.), and bloating characteristics of shales. The enquiry has been directed toward testing the usefulness of these properties in determining the following:A -The correlation of shale beds and, by inference, of coal seams, sandstone beds, or other such structures associated with them.B.-The location of contacts between marine and non-marine shales where lithological, palaeontological, or other evidence is lacking.Limitations of time and facilities have prevented a thorough investigation of this problem. The results given in the present paper are preliminary only. It is hoped, however, that they will occasion discussion or even lead to more thorough investigation of the method by individuals or organizations.There are, admittedly, various limitations to the proposed method. It is thought to show some promise when used in conjunction with the well-known and established methods used in stratigraphic correlation and, more particularly, when the conventional methods are not applicable."

Jan 1, 1952

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

Geology grads mine heated job market Salaries up 44 per cent in three years ?[Geology student] passed up a $100,000-a-year job at a mining company last December when he finished his degree in geology. The 24-year-old Canadian said he?s confident he?ll get a better offer.? Rob Delaney and Stewart Bailey, Calgary Herald, Published: Saturday, March 15, 2008 Massive shortages across the mining industry > Trades and operators are a large component > Technical people are equally hard to find > Students are in an excellent positions to secure exciting jobs > Experience is at a premium. Why?

May 1, 2008