Search Documents

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

Cameco Corporation is in the process of revitalizing the Key Lake mill. As part of this process, the company is considering installing the Rabbit Lake style strong acid stripping in solvent extraction. This would lead to using hydrogen peroxide for uranium precipitation. The process currently employs ammonia stripping and ammonia precipitation. As part of the process evaluation, an indirect fired drier pilot plant test was conducted. This paper will discuss the results of that test work, including the relationships between the following: ? Drying temperature and product grade ? Drying temperature and product colour ? Drying temperature and product reactivity with water ? Drying temperature and energy input requirements ? Drying temperature and shipping costs

Aug 1, 2010

By W. Qin

The nucleation of d hydride in Zircaloy-4 has been studied using electron backscatter diffraction. Hydrides prefer to nucleate at intergranular rather than intragranular sites. (0001) a -Zr//(111) d -ZrHx is the most common crystallographic relationship. The hydride platelets are generally interlinked each other and form a chain-like configuration. Based on thermodynamic model, the formation mechanisms of the hydrides at different sites and the interlinked structure were analyzed. We found that the misorientation of two adjacent grains has a crucial effect on hydride nucleation sites, and the tensile stress near the tips of hydride platelets is a key factor affecting the appearance of interlinked structure.

Aug 1, 2010

By D. Runnels, A. Allaire, J. Fournier, Y. Sylvestre, F. Robichaud

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By M. Maeda, H. Sasaki

Dissolution characteristics of metals vary significantly when they form alloys with other elements. Because hydrometallurgical processes are essential in separation and refining of non-ferrous metals, it is important to study behaviors of alloys in aqueous solutions. The authors have studied dissolution characteristics of precious metals in acid solutions using electrochemical measurement. When precious metals are alloyed with Zn, its dissolution is promoted by an increase in surface area caused by the preferential dissolution of this metal. The electrochemical study also revealed that precious metals dissolved from some alloys at unusually negative potentials; the underpotential dissolutions are explained by activations of these metals in the dealloying.

Jan 1, 2014

By F. Rosenblum, P. Spira

A laboratory test has been developed for assessing the patential hazard from self-heating of sulphides. The technique consists in measuring the rate of self-heating, from near ambient temperature, of a 1-kg sample in an insulated chamber controlled at standard atmospheric conditions. The rate of oxygen consumption is monitored simultaneously. The paper describes the apparatus and test procedure, and reports data on various ores and mill products. Tailings known to have caused problems underground when used as backfill have shown heating rates of over 3°C/h. A preliminary hazard rating guide for backfill based on the known behaviour of several sulphide materials is presented.

Jan 1, 1981

By B. R. Maas

Processing material at a consistent rate through the continuous countercurrent decantation (CCD) thickeners presented a major bottle neck to unlocking additional value from one of the post-flotation streams at the Kansanshi processing plant. The manual operation of the thickeners making up the CCD train resulted in frequent imbalances and process upsets across units. The automation of CCD trains is notoriously tricky as the available manipulated variables are outnumbered by the parameters requiring regulation. The implementation of an advanced, auction-based, control philosophy to manage the movement of both slurry and solution inventory through the train addressed this parameter imbalance and lead to the stabilisation of the circuit. Since the commissioning of this control strategy: an additional 7 200 dmt/day (+36% throughput) of material can reliably be processed through the train, the number of monthly downtime events has reduced, and a saving of $354 000/month in reagent cost has been achieved. INTRODUCTION CCD operation Agitated leaching is a common method used in hydrometallurgy to extract a metal from its host ore. The host ore is initially finely ground to liberate the surfaces of the valued minerals and improve the kinetics of the leaching process. The ore is then contacted in an agitated tank with a lixiviant to dissolve the desired metal into the aqueous phase. The resultant slurry from the leaching process comprises of a solution pregnant in the metal salt and a barren ore. The first purification step taken after leaching is to wash the pregnant liquor solution (PLS) from the depleted ore. On the industrial scale, a set of between two to ten thickeners arranged in a countercurrent configuration is often used to carry out this separation (Perry & Chilton, 1973). The slurry is introduced at the head of the train and a wash solution at the tail. The two streams are pumped through each thickener countercurrent to one other. At each stage the residual PLS in the slurry is mixed and diluted down with the countercurrent overflow solution from the downstream thickener. The diluted slurry is fed into the thickener where the solids separate out through gravity sedimentation. The settled solids are channelled towards the underflow of the thickener by a rake mechanism and pumped downstream to the next thickener in the train. The outcome is the recovery of a PLS from the overflow of the lead thickener and a slurry of washed solids from the underflow of the tails thickener.

Jan 1, 2019

By T. Hadley, Northern Minerals Ltd, C. S. Griffith, T. A. Safinski, K. H. Soldenhoff, M. Fainerman-Melnikova, A. Manis

"ANSTO Minerals and Northern Minerals have been working together since 2012 on the process flowsheet development for the Browns Range project for the recovery of the heavy rare earths (Dy – Lu, + Y). Initial efforts were directed toward defining the most efficient and direct flowsheet for the Preliminary Feasibility Study (PFS), issued in June 2014, then towards the Definitive Feasibility Study (DFS), issued in February 2015. These goals were achieved by undertaking comprehensive laboratory and continuous piloting programs. Further improvements to the flowsheet following the DFS have been made. This publication provides an overview of the evolution of the process flowsheet based on these laboratory and piloting programs from the PFS through the DFS and beyond.INTRODUCTIONNorthern Minerals Ltd (Northern) has been working on developing their flagship project at Browns Range for the recovery of the heavy rare earth elements (HRE, Dy – Lu, + Y). The project is located in the north of Western Australia as shown in Figure 1. The Total Mineral Resource at the project is currently estimated at 8.98 Mt @ 0.63% total rare earth oxides (TREO) comprising 56,663 t of contained TREO using a cut-off grade of 0.15% TREO. Of the Total Mineral Resource, 58% is classified as Indicated Resource, with the remainder in the Inferred Resource category.The deposit is characterised by breccia-hosted, hydrothermal, HRE-rich, xenotime mineralisation. The main gangue mineral associated with the xenotime is quartz. The distribution of rare earths (RE) observed for the xenotime mineralisation at Browns Range is presented in Figure 2. Extensive test work has shown that the xenotime can be readily beneficiated to between 20 – 40% rare earth oxide (REO) using a process consisting of crushing and grinding, followed by magnetic separation and flotation steps. Continuous piloting of this process was conducted on ~80 t of trench-sourced ore in late 2013 at SGS Perth, to produce ~2 t of ~20% REO mineral concentrate (MC) for hydrometallurgical testing. The composition of the MC produced during piloting is presented in Table 1."

Jan 1, 2016

By D. Fredlund

The decommissioning of uranium tailings facilities often requires the design of a suitable cover system. In northern climatic environments there is a portion each year that can be considered to be ?inactive? while the remainder of the year can be considered to be ?active?. There are numerous engineering design assumptions required when analyzing both the ?active? and the ?inactive? portions of the year. Cover systems are subjected to complex boundary conditions and nonlinear unsaturated soil properties. The proposed paper describes the steps necessary for the preparation and the analysis of a multi-year climatic database for the design of a cover system in northern environments. The paper also explains how climate can be classified and how observed variations from one year to the next can be taken into consideration in cover design. The results of climatic records at two different sites are used to illustrate conditions that need to be taken into consideration when designing soil cover systems.

Aug 1, 2010

By Andrew Kerr

Abstract - The base-metal and PGE contents of samples from magmatic sulfide mineralization are commonly correlated with their sulfide contents, indicating that the metal contents of bulk sulfides remain approximately constant within a given prospect or part thereof. Calculated sulfide metal contents provide valuable information in mineral exploration and research, but there are few formal descriptions and analyses of the procedures. Sulfide metal contents are best calculated using an assumed value (35.7% S) for a typical pyrrhotite-chalcopyrite-pentlandite mixture, and there appears to be little advantage in accounting for sulfide species separately. Regression of metal data against sulfur is probably the most rigorous approach, but is not always practical. Above 10% S, calculations are very robust, but lower sulfide contents generally demand at least some correction for non-sulfidehosted metals. Such corrections can become significant below 5% S, and/or in olivine-rich samples. They are best accomplished by mass-balance calculations, using concentration data from unmineralized host rocks. Significant uncertainties are introduced by analytical errors for sulfur, base-metals, and PGE, which are commonly measured from separate sample aliquots. These combined errors in sulfide metal contents generally exceed ±10%, but expand further at low S contents. In general, treatment of data from samples containing <2.5% S must be approached with caution, especially for PGE, for which the exact host minerals may not be known. Application of the method in simple grade-potential assessment is straightforward, but research studies involving sulfide-poor samples are inherently more complex. Under-correction or over-correction of data for non-sulfide-hosted metals can lead to false negative or positive correlations between sulfide metal contents and sulfide content. As the latter may itself be linked to geological parameters, such as depth within an intrusive body, undue significance could be ascribed to such trends. There are also valid geological reasons for such correlations, and such data require careful assessment to separate true and artificial variations. Propagated analytical uncertainties increase significantly in sulfide-poor samples, and must also be borne in mind whenever data from different localities or units are compared and contrasted.

Jan 1, 2001

By C. Bazin, D. Hodouin, M. Ounpuu

Sensors are now available in mineral processing circuits to monitor pulp flowrate and density, as well as ore characteristics and other process variables. The amount of information provided by these instruments is considerable but in many cases poorly exploited. This paper gives the results of the application of time series analysis techniques to signals generated by the sensors installed on an industrial Pb dezincing flotation circuit in New-Brunswick. Autocorrelation and cross correlation functions appear to be interesting tools for a preliminary circuit analysis, however the calibration of single input single output discrete transfer functions using collected sensors signals leads to conflicting results. For this reason a phenomenological approach, based on the kinetic and transport properties of the flotation process, is also considered. It has several advantages over the empirical transfer function modelling but also limitations in its applicability to industrial processes. A combination of the transfer function and kinetic modelling approches appears to be a promising avenue for better process modelling and control.

Jan 1, 1985

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By R. Ham-Su, J. P. Healey, S. P. Farrell, R. S. Underhill, M. A. Gharghouri, C. V. Hyatt, L. M. Cheng

Magnetic shape memory alloys (MSMA&apos;s) are a class of materials where magnetic energy can be converted into mechanical energy and vice versa. NiMnGa-based MSMA&apos;s have attained magnetic field induced strains up to approximately 10% and have a relatively wide operating temperature range, from well below 0°C to above RT, making them very attractive for a variety of applications. However, these materials also suffer from low toughness. Using these materials in a composite could mitigate this shortcoming, and also overcome limits imposed by inertia and eddy current losses. In this work, we describe the manufacture and characterization of such composites. Composites with 30% by volume MSMA were fabricated under a magnetic field resulting in anisotropic magnetic properties. Damping properties were evaluated by dynamic mechanical analysis.

Jan 1, 2004

By K. Shitogiden, Y. Samada, T. Miki

Steelmaking slag contains nutrition such as Si, P and Fe for acceleration of phytoplankton growth. Phytoplankton can fixate carbon dioxide more than any other species on earth. Hence, suppression of CO2 can be achieved by applying the potential of steelmaking slag as the nutrition for their propagation. When it is considered to supply nutrition from steelmaking slag to seawater, we must avoid dissolution of hazardous elements or change of pH of seawater by steelmaking slag addition into seawater. The protection against dissolution of fluorine into artificial seawater has been studied based on dissolution behavior of steelmaking slag and synthesized substances into artificial seawater in the present work. The dissolution mechanism of fluorine from steelmaking slag and buffering action of pH change are discussed by using stability diagram in seawater.

Jan 1, 2004

By D. E. Gill, A. Piche, S. Dufresne

"SOMMAIREUne méthodologie de prévision des coûuts de forage en galeries est proposée. Cette méthodologie a été élaborée pour les perforatrices pneumatiques manuelles. Elle est composée de quatre modèles: (1) un modèle de pénétration conduisant à la prévision du temps de forage; (2) un modèle d&apos;estimation de la durée de vie des fournitures; (3) un modèle d&apos;estimation de fa quantité d&apos;énergie consommée; et (4) un modèle de calcul de couts. Elle fait intervenir la résistance en compression uniaxiale de la roche du massif foré, le diamètre des trous, Ie type de perforatrice utilise, fa pression d&apos;air d&apos;opération, la longueur des fleurets, les temps morts associes au forage ainsi que le rendement des compresseurs, des perforatrices et du réseau de distribution de l’air comprime. L &apos;application de la méthodologie est illustrée à l’&apos;aide d&apos;un exemple, suivi d&apos;une courte analyse de sensibilité et d&apos;une brève discussion. ABSTRACTA drilling cost estimation methodology for underground headings is described. This methodology has been developed for percussive hand-held drills. It comprises four models: (1) a drillability model used for the prediction of the drilling period; (2) a model for the prediction of bit and rod lives; (3) an energy model; and (4) a cost model. It makes use of the uniaxial compressive strength ofthe rock drilled, hole diameter, drill type used, operating air pressure, drilling rod length, dead times that may occur during the drilling operation as well as compressor, air distribution network and drilling machine efficiencies. The application of the methodology is illustrated with an example, followed by a short sensitivity analysis and brief discussion."

Jan 1, 1994

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By K. J. K. Weglo, M. U. Savich

"At the Falconbridge Limited, Canadian Nickel Division, Sudbury Operations, we investigated the ""NO NOISE"" ear muffs model NN3-F which is a Swedish product with foam-filled sealing rings (the Hellberg Standard Volume Hearing Protector). It is used extensively at Falconbridge mines in Sudbury.The research which was carried out in the four Falconbridge mines was conducted under three different headings: manufacturer&apos;s attenuation data (psychophysical method), clamping force and head size (bizygomatic diameter), and attenuation tests (physical methods) under working conditions.Manufacturers of hearing protectors claim their products offer noise reductions of 23 decibels (NRR) or more, but they fail to point out that this reduction is obtainable only under ideal conditions. The reality of attenuation under working conditions, as several studies have found, is quite different.Methods for using short measurements to determine the noise exposure index, and for controlling muff-wearing habits, were developed at the Elliot Lake Laboratory. Measurements taken at Falconbridge on ""NO NOISE"" ear muffs revealed that they have a practical attenuation of some IO to 13 decibels. It is important to note here that measurements also revealed that clamping force (thus attenuation) was in an inverse relationship with ear muff comfort. Measuring attenuation using noise dosimeters was a difficult job. Not a single surveyor would accept these measurements (physical method) for absolute accuracy. Apart from that, it was impossible to measure, in one shift, more than two work stations. Because of this, we sought a solution: measuring head size and clamping force in relation to actual attenuations.A detailed analysis of the relationship between attenuation and head size/clamping force was done at four mines. Standard deviation ellipses (standard error ellipses) for head size versus clamping force are in close agreement with measurements that were carried out. In order to measure clamping force an apparatus was constructed and a method for measuring suspension system durability is described in Appendices Band C of this report. At the same time we sought to reduce deterioration of ear muffs in mines as well as to put in place a system whereby attenuation can be controlled and improved. The clamping force apparatus can be operated automatically. The proposed control system is quick, simple and efficient . This system is equally applicable in small and large mining operations, and it can be totally automated and the data computerized for audit of the results. This control system is a new step in controlling ear muff attenuation in working environments.From these measurements of NN3-F ""NO NOISE"" muffs it can be concluded that ear muffs are not the total solution to protect the worker from noise.As the results were evaluated folio wing measurement, Falconbridge switched from the NN3-F ""NO NOISE"" muffs to approximately 90% Mark V ""NO NOISE"" muffs and 10% Mark V MSA muffs. These new muffs showed much better head size versus clamping force relationship and can be expected to produce 14 dBA or better attenuation of noise. RESUMEUne étude des casques antibruit ""NO NOISE"" modèle NN3-F, de fabrication suédoise, avec anneaux d&apos;étanchéité en mousse (dispositif de protection contre le bruit ""Hellberg "" pour volume ordinaire)a été effectuée Ii la Falconbridge Ltd. , Division canadienne du nickel aux installations de Sudbury . Ces casques sont largement utilisés dans les mines de la Falconbridge Ii Sudbury.Cette étude aeu lieuen milieu de travail dans les quatre mines de la Falconbridge sous trois rubriques différentes soit: les données d&apos;atténuation du bruit du fabricant (méthode psychophysique), la force de serrage et la taille de la tète (diamètre bizygomatique), et les essais d’atténuation de bruit (méthodes physiques). Les fabricants de dispositifs de protection contre le bruit prétendent que leurs produits offrent une réduction du bruit s&apos;élevant Ii"

Jan 1, 1986