Search Documents

By W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By L. Tikasz

The primary purpose of ore hauling model studies is to capture the variability of the ore delivery ? stockpiling process in order to improve the estimation of equipment capacities and achievable throughputs. The operation of a mine-to-site ore delivery system is the subject of a number of challenges. Typically, ore is hauled by a given combination of trucks, conveyors and trains. In addition, ore loading, ore transferring to another means of delivery, stockpiling, reclaiming, and further deliveries involve many other types of equipment. The concurrent operation of all these units is scheduled; nevertheless, they are subject to planned maintenance and random breakdowns. To support our engineering design work on ore hauling operation, discrete event type models were built for each specific task. Then, due to recurring demands, an ore hauling library was gradually compiled. The now available model library allows fast and efficient simulation of various mine-to-site hauling arrangement, adaptable to various mining and mine construction operations (e.g. bauxite, iron ore, copper ore and coal).

Aug 1, 2013

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By M. M. Holgate

"Porosity neutron deflection scales can be derived more easily by cumulative correlation than by the conventional method of plotting corresponding points on a graph. The micro-log can be used as a porosity datum for the neutron log by transforming the permeability cut-off it shows to a porosity cut-off by a permeability-porosity function obtained from core analysis. Porosity footage values calculated in this manner from the neutron log are within 20 per cent of core analysis values."

Jan 1, 1960

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter's Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American's SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District's inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the 'Environmental Strivers', which created a recycling centre in the community; and the 'Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By R. C. Wallace

Since the time when Canada's East and West were joined by the railway, and communication was established into the interior, settlements grew on the southern fringe of the great Precambrian area that formed the northern protaxis of the continent during its vicissitudes of growth. They clung precariously to the fringe of that ancient land, for the Precambrian is not generous to those who wish to live by the fruits of the soil, except in those limited areas where the Pleistocene ice-sheet has been profuse in its gifts of clay to cover the hard surface of the Precambrian rock. Later settlements spread westwards over the expanse of Cretacean plains that now form the wheatfields of the Canadian West; but there still remained in northern and western Ontario, in eastern and northern Manitoba, a pioneer race, to whom agriculture had attractions only in so far that it provided the wherewithal to lay siege to the riches of the Precambrian. And they had a vision beyond their time. More than they knew, they had seized the fact that for the complete rounding out of Canadian national life, a8 well as for the establishing of the necessary contributions towards the economic stability of Canada and its provinces, an industry in mining sh01.dd be well and truly built in the hinterland of the central provinces. Failing the winning of mineral from the rocks, and timber from the forests, there would remain between the East and the West an enormous barrier of unproductive country which would not only be an incubus to the agricultural people in their struggle for economic liberty, but would effectively, and for all time, remain an un-populated void across which the aspirations of East and West would be unable to unite.

Jan 1, 1924

By Tanveer Jahir

With increasing energy costs and mounting government pressure to adopt low emission, green sources of energy, it has become imperative to develop long-term sustainable underground infrastructures that exhibit low power consumption. Underground mining environments are mandated to have ventilation systems in place to replace polluted air with clean air. Continuously running air ventilation systems have proven to be an expensive solution for this requirement. Ventilation-on-demand (VOD) is a cost effective method for not only reducing energy consumption and greenhouse gasses, but also ensuring the safety and well-being of the miners beneath the surface. VOD is achieved by monitoring the air quality in target areas of the mine, and based on variables such as the number of personnel in the area, the number of emission-emitting vehicles, the air leakage around doors and entrances, dust levels, and other key environmental details, the speed and angles of the fan blades are adjusted to increase or decrease the volume of air flow. For over 40 years, Conspec Controls has been developing systems capable of VOD through the use of controllers, gas monitors and personnel/vehicle tracking equipment, providing inexpensive, reliable solutions for underground ventilation.

May 1, 2011

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007