Search Documents

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By T. D. Chatwin

Acid rock drainage (ARD) is one of the most serious and potentially enduring environmental problems of the mining industry. High liability costs carried by many mining companies to cover potential obligations of ARD are a clear indication of the gravity of the problem. Unchecked, ARD can result in water quality impacts that could well be the industry's most significant financial and credibility risk. Effectively preventing acid drainage is a formidable challenge that requires the total commitment of the mining industry throughout the entire life-cycle of a mine. To achieve this commitment a strong business case for ARD prevention must be developed. This paper will address the elements of acid prevention and discuss their importance not only to the company but the entire industry as well. The International Network for Acid Prevention (INAP) is an industry-led group created to help meet this challenge. In 2009, INAP published the GARD Guide (www.gardguide.com), a web-base best practices guide for the prevention of ARD [1]. In this paper, the GARD Guide will be used to identify preventative actions for all mining industry stakeholders. It will, in turn, be used to estimate ARD management and mitigation value accrued to the company from ARD prevention, which will be used in developing a business case for acid prevention.

Jan 1, 2011

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By N. Hosking, M. Nichols

Aluminum alloys are increasingly used for automotive body construction but are susceptible to filiform corrosion or paint blistering in service. Filiform corrosion resistance of two 6000-series aluminum alloys was investigated in this work. Test panels were produced with full automotive coating layers and scribed parallel and perpendicular to the rolling direction. The corrosion exposure comprised an inoculation step with acidified salt solution followed by a 6-week exposure period at 95% relative humidity and either 25°C or 70°C. Greatest corrosion activity was measured on the alloy with higher copper content, AA6111. Higher temperature exposure led to greatly enhanced corrosion activity for AA6111 compared to the lower temperature exposure. The 70°C exposure also led to greater mean corrosion-affected area measurements for the low copper aluminum alloy, AA6022, but the effect was not as stark as that observed for AA6111. Rolling direction affected the propagation direction, and possibly mechanism, of the corrosion effects. Cross-sectional analysis revealed dense corrosion products within the filament, comprising mostly aluminum and oxygen but with traces of chloride and sulphate. Development of varying filament and blister types on a single test panel and the progression of corrosion underneath a filament into the substrate indicate that several corrosion mechanisms can develop on the test panel, testament to the complexity of the corroding surface developed on an aluminum automotive body panel.

Jan 1, 2015

By F. H. Edmunds

LLOYDMINSTER is the centre of a well developed agricultural area, lying on the Alberta-Saskatchewan interprovincial boundary in Township Fifty. The surrounding country is gently undulating, without any notable topographic features, but twenty-two miles to the north the North Saskatchewan river, and thirty miles to the south the Battle river, have cut deep valleys. In the spring of 1934, a wild-cat well (Lloydminster Gas Company's No. 1 well) was successful in striking a large flow of gas at a depth o 1,974 ? feet. The gas was piped into the town, a short distance south, and Lloyd-minster became the first Saskatchewan town to be served with natural gas. Following this discovery, other wells were sunk and, up to the present, thirteen wells have been drilled m what is here designated the Lloydminster area. Ten of these wells are in Saskatchewan and three in Alberta. Seven were successful in obtaining gas, three oil, and three have been unsuccessful. The area tested by this drilling is about eight thousand acres, six thousand of which can be considered as proved gas or oil land. To the south and west of Lloydminster, in the Province of Alberta, there are several areas in which oil and gas have been discovered. The Wainwright field lies nearly fifty miles to the southwest; Battleview, where recently gas has been discovered, is thirty miles west-southwest; and the Ribstone area is about thirty miles south and a little west. At Ribstone, a number of wells were drilled some years ago and there is a small production of oil. The data relating to the wells in the Lloydminster area that are recorded in this paper are taken from the records of the several companies operating in the field. The names of these companies are given on the map and on the type stratigraphic section (Figures 1 and 2). The author wishes to record his appreciation to Mr. R. H. Shaw and Mr. 0. C. Yates, both of Lloyd-minster, for much valuable information; also to Mr. E. Swain, of the Department of Natural Resources, Regina, with whom the writer has visited the field on several occasions, and who, by his enthusiasm and encouragement, has done much to forward the development of the area. The well samples were examined at Ottawa by officers of the Borings Division of the Geological Survey of Canada, who also made the interpretations of the logs. Frequent references will be made to the work of Dr. G. S. Hume, of the Geological Survey, and the writer would like to pay tribute here to his work.

Jan 1, 1940

By B. S. Ignasiak, Dennis Carson

"Laboratory study of the behaviour• of binary coal blends shows that coke strength is more closely dependent on the distribution of ""reactive"" oxygen in the parent coals than on their proximate, elemental or petrographic compositions, and it also appears possible to qualitatively predict coke strength from information about reactive oxygen. Proceeding from this recognition, experiments were carried out to test the possibility of preparing metallurgical cokes from binary blends in which non-caking hvb coal was substantially freed of reactive oxygen by prior heat t1•eatment under controlled conditions. The results indicate that such blends can yield surprisingly strong cokes and that coke strength may be amenable to further improvements by modifying the size distribution of the pre-heated component and the rate at which it is charred."

Jan 1, 1976

By James J. Holmes

ACCIDENT prevention as we know and understand it today is of comparatively recent origin. As a matter of fact, the Industrial Accident Prevention Association of Ontario, which is the oldest organization of its kind in the Dominion, celebrated its thirtieth anniversary only this year. On the other hand, one could say that the history of accident prevention is almost the history of mankind itself. In a general sense, every forward step that man has made throughout the centuries has been largely due to two things: (1) a desire for increased comfort, and (2) the need for safety; and, always, the need for safety has taken precedence over the desire for comfort. While it is true that hundreds of volumes have been published, dealing with the many aspects of accident prevention work, you cannot go to a library and pick out a book that has all the answers in it. Such a book has never been published-we are still looking for some of the answers. However, a good deal of real progress has been made.

Jan 1, 1945

By R. Yost

"This paper describes a case study that illustrates how detailed geological engineering results were communicated to address a range of stability challenges in a producing mining environment. Instead of using standard geological engineering terminology, findings and recommendations were communicated as mine design options and mining responses to accommodate possible slope instabilities and associated risk. The resulting medium- to long-range mine plan integrated the potential slope instabilities and associated mining responses to provide a higher probability of planned resource extraction. It also reduced the potential for long-lasting production and processing delays.RÉSUMÉ Cet article décrit une étude de cas illustrant l’intérêt de la communication de résultats détaillés de géologie appliquée pour résoudre un éventail de difficultés relatives à la stabilité dans un environnement minier en production. Plutôt que d’utiliser une terminologie classique de géologie appliquée, les résultats et les recommandations ont été communiqués sous forme d’options pour la conception d’une mine et de réponses dans le contexte minier permettant de surmonter les éventuelles instabilités des pentes et les risques associés. Le plan de mine sur le moyen à long terme qui a résulté intégrait les instabilités potentielles des pentes ainsi que les réponses connexes dans le contexte minier afin de renforcer la probabilité de l’extraction des ressources prévue. Il réduisait également la possibilité de retards durables dans la production et le traitement.INTRODUCTIONSlope failures in an active mining operation are unscheduled but expected events, in the sense that the geotechnical design often assumes the potential for slope failure but cannot predict exactly when a failure will occur. Unfortunately, the geotechnical engineering cycle—characterization, slope design, displacement monitoring, instability management, and failure remediation—that is necessary to manage slope-failure risk is not always well known or understood outside the geotechnical engineering profession. The first introduction many personnel have to geotechnical engineering is when a slope failure starts to develop and appears to threaten the safety and livelihood of their workplace.At that point, the task of communicating the risk management of slope failure falls to the geotechnical engineer, who must summarize analytical methodology, design concepts, monitoring trends, and analysis results, frequently to an audience with limited exposure to the geotechnical field. All too often, the response has been to present a risk-management plan in the vernacular of geological engineering— using terms such as factor of safety (FOS), pore-pressure reduction, and slope unloading—instead of expressing the problem and solution in more readily understood mine production terms."

Jan 1, 2017

By M. J. King, D. A. Van den berg, R. Fukuzawa

"Mercury bearing ore bodies are often treated for the production of copper, lead, zinc, gold, and silver. The mercury deports either to tailings or is collected during various stages of the extraction process. This paper reviews the relationship between various mercury collection processes and the subsequent management of the mercury by-product or waste. It focuses on mercury removal sequestration including cementation, sulphide precipitation, bulk neutralization, and carbon adsorption. Long term mercury management strategies including third-party stabilization, stabilized mercury co-disposal, secure storage, and mercury recycle are also evaluated. INTRODUCTIONMercury is produced in North America as a by-product of non-ferrous metals processing and from recycling of products such as dental amalgam, fluorescent lamps, and thermometers. Its toxicity is recognized to have significant negative impacts on the environment and human health. As a result, many countries are adopting regulations limiting mercury use and its uncontrolled release.The European Union banned mercury exports in 2011 and the United States will do so in 2013. The export bans aim to prevent mercury use in developing countries for activities such as artisanal small scale gold mining. However, by-product mercury production from the non-ferrous metals industries continues.These factors contribute to an oversupply of mercury and the need to find suitable treatment methods for the long term management and storage of mercury and mercury bearing materials."

Jan 1, 2012

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By Jayne Somers

Methane (CH4) is a potent greenhouse gas, accounting for 15 percent of all global greenhouse gas emissions in 2005. Since methane has a much shorter atmospheric lifetime than carbon dioxide (CO2), reducing methane emissions can achieve considerable climate benefits over the next 25 years. Coal seams often contain significant quantities of methane and CH4 released to the atmosphere from gassy mines during coal extraction is a major source of greenhouse gas emissions. Methane (CH4) emissions from coal mining activities constitute approximately 6% of total global human-related methane emissions. Coal mines around the world have recognized that methane is a clean energy resource that can be captured and used productively. Coal mine methane (CMM) is currently utilized for power generation, natural gas pipeline injection, vehicle fuel, industrial process feed stocks, on-site mine boilers, mine heating, and home heating distribution systems. Upgrading mine degasification systems can often improve gas quality and create favorable project economics. The United States has been a leader in coal mine methane (CMM) recovery and use since the 1990?s. There are now 15 projects at active underground mines in the U.S., as well as 26 abandoned mine methane projects. Recovery and use projects at active underground U.S. mines reduced methane emissions by approximately 49 Billion cubic feet in 2010. In an exciting new development, a ventilation air methane (VAM) mitigation project at the CONSOL McElroy mine in West Virginia was installed by Verdeo. Operational since September 2012, this is the first commercial-scale VAM project in the U.S. and the project will reduce methane emissions by an estimated 920 MMCF/yr. As part of the U.S. Greenhouse Gas Reporting Program, actual data on methane emissions from underground coal mines was collected for the first time in 2011 and reported to U.S. EPA in September 2012. The data collected will help inform stakeholders, particularly the underground coal mining industry, of CMM emission sources on public and private lands. The detailed data will also shed light on the specific sources of methane from active underground coal mines and highlight project opportunities for the U.S. coal industry. The paper will cover U.S. coal mine methane emissions, U.S. CMM utilization and destruction projects, Federal policies and State incentives for CMM capture and utilization. 2011 CMM data from the U.S. Greenhouse Gas Reporting Program Subpart FF will be analyzed and compared with previous U.S. Greenhouse Gas Inventory estimates. Other developments, including the voluntary carbon market, will be discussed.

Aug 1, 2013

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951