Search Documents

By R. E. Whitehead

"Abstract - Alkali-alumina and MgO-alumina plots are an effective instrument for displaying chemical and mineralogical compositions of altered and unaltered rhyolites and rhyodacites. They reveal that most supposedly unaltered rhyolites, apart from those of Cenozoic age, have undergone losses in Na2O and gains in K2O. The extreme loss of Na2O from highly altered rhyolites immediately adjacent to VMS deposits is strikingly illustrated by alkali-alumina plots. MgO/Al2O3 vs. K2O/Al2O3 diagrams display a strong negative correlation between MgO and K2O that results from the conversion of sericite to chlorite. A similar negative correlation between MgO and whole-rock d18O is apparent on plots of these two parameters. Alkali-alumina plots underscore problems in selecting appropriate precursor compositions required for mass-balance calculations. Molar ratio plots are a viable alternative to such calculations. Sommaire -Les diagrammes alcali-alumine et MgO-alumine constituent un instrument efficace pour la représentation des compositions chimiques et minéralogiques des rhyolites et rhyodacites altérées et fraîches.Ces diagrammes révèlent qu’à l'exception de celles d’âge Cénozoïque, la plupart des rhyolites qualifiées de fraîches ont subi une perte de Na2O et un gain de K2O. L’intense perte en Na2O que l’on note dans les rhyolites fortement altérées associées aux gîtes de type SMV est particulièrement bien mise en évidence par le diagramme alcali-alumine. Le diagramme MgO/Al2O3 vs. K2O/Al2O3 montre une forte corrélation inverse entre le MgO et le K2O due à la conversion de la séricite en chlorite. Une corrélation inverse analogue entre le MgO et le d18O de la roche totale s’observe sur un graphe comparant ces deux paramètres. L’usage du diagramme alcali-alumine fait ressortir combien il peut être difficile de choisir un précurseur de composition appropriée pour des calculs de balance de masse. Les diagrammes de rapport molaire constituent une alternative à de tels calculs."

Jan 1, 2006

By W. Dietzel

Fracture mechanics based techniques are used to gain insight into the phenomenon of stress corrosion cracking (SCC) and to develop guidance for avoiding or controlling SCC. From constant extension rate experiments under rising load or rising displacement conditions the susceptibility of high strength steels, aluminum, magnesium and titanium alloys to SCC and hydrogen embrittlement can be assessed. Such tests on pre-cracked specimens are also well suited for studying the mechanisms leading to SCC by employing appropriate models for the degradation of metallic materials which take into account the uptake of atomic hydrogen from the corrosive environment. Measurements of crack growth resistance curves using the crack tip opening displacement as fracture parameter can be compared with simulated R-curves obtained from modeling of the mechanism of hydrogen embrittlement. The materials investigated are a high strength steel and a magnesium alloy both exposed to environmental conditions which fostered the uptake of hydrogen.

Jan 1, 2010

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By A. J. MacEachen

"LIKE ALL OTHER NOVA SCOTIANS, I have been thrilled during the past few years with the growing evidence that substantial reserves of oil and gas are being discovered off the Atlantic coast of Canada. There are those in this province who believe that large-scale commercial production is just around the corner, and that when it starts Nova Scotia will begin to float on a sea of royalties. These overly optimistic people, of whom I am not one, are convinced that with the first barrel of oil shipped to market, Nova Scotia can forget its financial problems while its people take on the luxurious lifestyle of the shieks of Kuwait or Saudi Arabia. You and I know, however, that even though offshore oil and gas may turn out to be the greatest gift nature has ever bestowed on Eastern Canada, it may take some considerable time before the reserves can be accurately assessed, before the industry can become fully operational, and before the benefits of production can be translated into royalties and tax revenue, improved public services, new industrial facilities and more jobs. While it is premature for the ordinary Nova Scotian to take on the habit of buying expensive cigars and lighting them with ten-dollar bills, it is not too early for him to insist that governments and industry plan intensively and well for the beneficial exploitation of undersea resources."

Jan 1, 1973

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

By J. Poplawski

In mineral processing plants, cyclones typically perform the classification duty prior to the downstream recovery process. Particle size distribution of the cyclone overflow is an important parameter and can be viewed as the product of the comminution process. Too coarse of a product will likely have poorly liberated valuable minerals and make recovery difficult. Too fine of a product may represent a missed opportunity to increase plant throughput and/or also result in low recovery due to poor kinetics. “Near-line” particle size measurement instrumentation has been in place for several decades, its availability and low measurement frequency have typically been inadequate for reliable use in automatic control. CiDRA Minerals Processing has developed a novel and robust technology that provides a highly reliable and low maintenance system for “on-line” measurement of the particle size in the overflow of individual cyclones. The system is based around a wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter. The system does not require sampling and associated sample transfer piping that is prone to plugging, thus avoiding high maintenance requirements. Plant data and benefits realized from the latest installations of the CYCLONEtrac PST will be presented. INTRODUCTION Impact-based real-time hydrocyclone particle size measurement Acoustic impact-based particle size tracking is a unique method for measuring and controlling the particle size in cyclone overflow streams. The implementation of this technology is centered upon a sensor probe that is inserted into the overflow slurry stream via a two-inch (50 mm) hole in the overflow pipe (Figure 1). Particles within the slurry stream impact the surface of the probe generating travelling stress waves within the probe. A sensor converts these travelling stress waves into an electrical signal and proprietary signal processing techniques convert these signals into a particle size measurement that is output every four seconds. The sensor is constantly in contact with many particles in the slurry stream, thus obtaining information from orders of magnitude more particles than traditional sample-based technologies. The sensor has no impact on cyclone performance because it is located downstream of the hydrocyclone and the presence of an air core ensures there is no change in the back pressure seen by the hydrocyclone.

Jan 1, 2019

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By R. E. Gilmore

Introduction The Sydney coal-field extends for a distance of thirty miles along the northeastern coast of Cape Breton island. At a central focal point at the tip of the south arm of Sydney harbour, seven miles or so in from the Atlantic ocean, is the city of Sydney, with Port Morien to the southeast and Sydney Mines to the north . Mining centres along the ocean coast between these points include Birchgrove, Reserve, Glace Bay, and Waterford. The field is divided into three districts or 'basins', namely, Morien basin to the south, Glace Bay in the centre, and the Lingan-Sydney Mines basin to the northeast. The eastern and western portions of the latter are known as the Lingan and the Sydney Mines basins, respectively. Six distinct coal seams are described as existing in the Morien basin, nine in the Glace Bay basin, and six in both the Lingan and the Sydney Mines basin. Although known by different names in the several basins, a definite continuity of the seams has been established.

Jan 1, 1933

By L. M. Pidgeon

Abstract The production of metallic calcium, by reduction of lime with aluminium, was investigated. Using a modified form of the effusion method, the vapour pressure of calcium above the reaction: 4CaO + 2Al ~ 3Ca + CaO.AI203 was determined and found to vary from 1.0 to 1.3 mm. Hg from 1,150° to l,200°C. From the magnitudes of the various thermodynamic quantities involved, together with a consideration of the known chemical characteristics of the reaction, it was suggested that the reaction proceeded by reduction of lime with aluminium vapour. INTRODUCTION The conventional production of metals by reduction of their ores by carbon (or carbon monoxide) may be represented by the equilibrium: MO+ R [] RO+ M . . . . . . . . . .(1) where MO represents the metal oxide, and R the reducing agent (carbon or carbon monoxide). The free energy change ?F° associated with the reaction is given by -?F° = RTlnKp . . . . . . . . ... . (2) where R is the gas constant, T the absolute temperature, and KP the equilibrium constant. It should be noted that ?F° represents ? the standard free energy gained by the system and hence -?F° is the free energy gained by the surroundings - and that as ?F° increases K must decrease, and conversely. For metals above manganese in the electromotive series, the ?F° associated with reaction would quantity and from it can be seen that this corresponds to a small fraction for K. The equilibrium pressure of the oxide of carbon represented by RO is then too near its concentration in the furnace gases for the reaction to proceed in an internally fired furnace. For the practical reduction of such metals, fuel fired furnaces are inadequate. Electric furnaces may be used to give higher temperatures with lower concentration of carbon oxides and the reaction may still proceed. However, for many metals such as calcium and aluminium the formation of stable carbides or acetylides may prevent production of the metal by this reaction. In this case, either electrolytic methods must be used, orrecourse must be had to reducing agents other than carbon. It is the latter method which is under consideration here.

Jan 1, 1948

By Mark Freberg

"IntroductionThis chapter is intended to provide information on the operation and maintenance of several pieces of equipment used in heavy media separation. Most heavy media separation circuits, particularly those involving bath separators can be considered as high maintenance areas. Because of this the efficient operation and maintenance of these circuits is very important if the cost per ton of material treated is to be kept to an acceptable level.Heavy media separation (HMS), is a process used to separate particles of different specific gravities. Under laboratory conditions the ideal way to separate two types of particles which have different specific gravities is to suspend them in a heavy liquid which has a specific gravity between those of the two types of particles. Those particles with the lower specific gravities will float on top of the liquid while the higher specific gravity material will sink to the bottom. Given enough time and a sufficient volume of heavy liquid this process will be essentially insensitive to the sizes of the particles involved.Heavy media separation circuits make use of the same principles described above. The material to be treated is introduced into a mixture of finely ground solids, called media, and water which takes the place of the heavy liquid; the mixture of solids and water is known as medium. The separating force can be either gravity or centrifugal force. The type of solids used as media varies but it is usually a high specific gravity material such as magnetite, galena or ferrosilicon.Heavy media separation is used extensively in the cleaning of coal and to a lesser extent as a preconcentration step in base metal and iron ore operations."

Jan 1, 1989

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

"3.1. IntroductionAmong the six platinum-group elements (POE), four have identical cubic symmetry, two identical hexagonal symmetry (Table 3.1). Despite crystallographic differences, there is a clear relationship expressed in the chemistries of the POE: they tend to be mutually soluble in one another and can frequently substitute for one another in compounds with other elements. This chapter consolidates the data on phase relations of the POE and the compounds they form with elements selected for their known or potentially important mineralogical significance- As, Bi, Cu, Fe, Hg, In, Ni, Pb, S, Sb, Se, Sn and Te-together with selected data for the occurrence of POE in certain elements such as Au and Ag, and compounds such as FeS. Resources used to compile the data are those available from the chemical, mineralogical and metallurgical literature. First each element is discussed, with composition limits of solid solutions drawn from binary phase diagrams. Single element data are followed by a discussion of the relevant binary systems and a tabulation of data for binary compounds found in those systems (Table 3.2). Tables and diagrams for the ternary and quaternary systems for which information is available follow, and finally the very limited information on the solubility of POE in mineralogically important elements and compounds is presented.The chemical, mineralogical and metallurgical literature on the unary and binary systems is extensive and widely scattered in many languages and publications; fortunately, most of the data needed to compile this chapter can be found in reliable compendia. The most useful and most recent of these works is by Moffatt (1979), because it provides a ready index to all material relating to binary systems listed in previous compendia; furthermore, the Moffatt compendium will reportably be kept up to date by annual supplements."

Jan 1, 1979

By Fred W. Snow

THE mines of the Consolidated Copper and Sulphur Company, consisting of the Eust1s, the Albert, and the Capel mines, are situated w Ascot township, Quebec, about ten miles southeast of Sherbrooke, on the main line of the Quebec Central railway. Of these mines, only the Eustis is now producing, and it has been operated almost continuously for the past seventy years. Mining methods have been improved in recent years but are still old fashioned when compared with those employed in more modern and up-to-date mines. The ore is of milling grade and is mined for its copper and sulphur con-tent. Silver is present in small quantity, together with a trace of gold. The ore is mined by the shrinkage stope method. Pillars are frequently left as supports for the hanging-wall to prevent serious dilution of the ore and are sometimes recovered after the ore is drawn from the stope. Occasionally, small blacks of ore in close proximity to the shaft are mined by a cut-and-fill method. HISTORY ALBERT AND CAPEL MINES: The Albert and the Capel mines, originally known as the Capelton mine, were discovered in 1863 by George Capel (1). By the end of 1866 the Albert shaft had been sunk to a depth of 121 feet on an incline of about 30 degrees where a vein five feet thick was encountered. In 1879, these mines passed into the hands of G. H. Nichols and Company, by whom they were operated practically continuously until 1907. When mining operations ceased in that year, the shafts had reached depths on the incline of approximately 2,300 feet and 1,000 feet, respectively. These mines have been allowed to cave and fill with water and have been inaccessible for many years.

Jan 1, 1936

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965

By W. A. Lang

Introduction That the coal industry has entered a new phase in its development is now evident. Coal, besides being the chief source of heat and power, has become a potential raw material for many industries. Rapid progress has been made in the methods used in the mining and preparation of coal, and in the equipment for the burning of coal. Data of a fundamental nature relating to the composition of coal and to its transformations? during combustion and processing have also been revealed. Research, the key which has opened this new era, has already accomplished much, but it has only begun to show what it may and should be able to do. New developments of coal burning equipment, super-power plants, carbonizing and briquetting plants, hydrogenation and synthetic chemical processes, will undoubtedly have a marked influence in the post-war years on the economic welfare of many coal producing countries. Until comparatively recently, however, there has been in many branches of the coal industry a tendency to regard research as something abstruse and something which had little or no value to those managing such branches. But the fact that coal has suffered as a source of heat and energy through inroads of oil, natural gas, and water power, has made it plain to the industry that, if it is to maintain its present markets in this competitive world, much less increase them, the whole industry must be willing to follow the example of other industries and plan for the future.

Jan 1, 1946