Search Documents

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By W. A. Lang

"IntroductionCARBONIZATION, gasification, and chemical utilization of coal are interrelated topics, which makes it difficult to review one without indicating its connection with the others. Hence, in Progress in Coal Technology, Series No. 5: Carbonization, reference was made to gaseous products recovered in the carbonization of coal, and .to a number of chemicals made from the tars, light oils, and ammoniacal liquors which are by-products of coal carbonization.In this, the sixth paper in the review series, prime consideration will be given to the complete gasification of coal to give a fuel for domestic industrial, or power purposes and a synthesis gas suitable for the manufacture of gasoline, Diesel oil, and chemicals. The hydrogenation of coal, an alternative source of liquid fuels and of chemicals, will be reviewed, as will be a number of processes for •the recovery of chemical products from coal by extraction and chemical treatment."

Jan 1, 1952

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By Andrew D. Lapworth

The use of geological and grade models has been standard practice in mine design for many years now, with a wide range of software available to create and analyze the models. Although geotechnical parameters are also of vital importance for mine planning, there has been very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology based on digital photography for automated, safe and accurate 3D mapping of geological and geotechnical features in rock faces. Datamine has integrated this capability into its product range so that Sirovision becomes an integral part of day-to-day face mapping, mine geology and geological / geotechnical modeling in both open pit and underground mines. This results in improved fragmentation for loading, hauling and processing, and for open pits local geotechnical conditions can be taken into account to improve slope design and control. This paper describes some of the ways that geotechnical modeling can be used to create more refined and cost effective mine designs and then discusses the role of Sirovision in enabling the raw data required for such modeling to be collected quickly, safely and reliably.

May 1, 2007

By W. J. Kuit

Since closure in 1968, the Wedge Mine, situated adjacent to the Nepisiguit River in New Brunswick, has been flooding with acidic water containing toxic levels of heavy metals. Cominco Ltd. has undertaken a series of pollution control measures to mitigate the threat posed to the river quality. Included has been a successful treatment campaign in 1976 which discharged in excess of 30 million gallons of high-quality effluent from the accumulated volume of mine water. The sources of contamination have been identified as actively leaching waste dumps. A comprehensive program of permanent corrective measures has been prepared which will culminate in mine backfilling. Once completed, the unacceptable burden of water treatment in perpetuity at a non-producing property will be removed.

Jan 1, 1977

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By Jeffrey D. Eisenman

FRP is a proven material for the solvent extraction processes of copper production. There is a history of successful applications of FRP piping and equipment in hydrometallurgical processing. The performance of FRP equipment has not always been consistent, but at no fault of the material. Its non-metal attributes and behavior vary from those of more typical materials of construction, such as steel and alloys. FRP is a mainstay material in many areas of solvent extraction and electrowinning and yet not well understood by all. We will discuss the critical concerns, which are key to reliable performance of FRP systems. This paper will include discussion of key elements, which are fundamental to reliable FRP piping design and considered best practices. Essential design and construction considerations to maximize reliable service life of FRP equipment, such as thickeners and process vessels, used in copper extraction and processing, will be discussed. Additionally, we will expose potential pitfalls and share lessons learned from previous copper processing plant projects, which can aid and impact other copper processing projects to ensure best system performance and reliability. INTRODUCTION The corrosion resistant attributes of fiberglass reinforced plastics (FRP) make it an attractive and cost effective material of construction in corrosive service applications that are found in copper processing. FRP is used all over the processing plant in seawater, brine and sulfuric acid services where the corrosive nature of these services would challenge most ferrous materials and coatings. FRP is a fully customizable material to meet the specific needs of each service and process. FRP piping and equipment can be found throughout the hydrometallurgical process, in the acid plant, desalination, leaching processes, solvent extraction and electrowinning to name a few. Beyond its superior corrosion resistant characteristics, FRP can be made abrasion resistant by introducing particulate additives into the resin, such as silicon carbide and alumina oxide. Because many of these services have combustible organic elements in the flow streams with accompanying safety concerns, the linings can be made conductive with carbon fibers to dissipate static charges that might collect on the surface of the equipment otherwise. Further, FRP can be made flame retardant as well, where flammability may be of concern.

Jan 1, 2019

By R. A. Brown

RIGHT NOW the Canadian oil business is suffering from growing pains brought on by developments outside our borders. I would like, therefore, to place our industry in perspective for you in two ways. I would like first to describe it briefly and let you see it in relation to the world oil industry. Then I would like to bring it back and place it into perspective against a strictly Canadian background. Naturally, in such a discussion, it is necessary to use a certain amount of statistical material. I'll endeavour, however, to keep it to a minimum. Eleven years ago, before the discovery of Leduc, Alberta could boast of having 21,000,000 barrels of crude oil reserves. Five years ago we had 1,810,000,000 barrels. At year end, 1957, our remaining recoverable reserves totalled more than 3,000,000,000 barrels. In 1957, our potential production in Alberta reached an all-time high of 756,000 barrels a day. Unfortunately, our actual average daily production dropped from 393,000 barrels per day in 1956 to 376,000 barrels per day in 1957. And in 1958, to date, it has dropped sharply to around 300,000 barrels per day.

Jan 1, 1958

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By David Weiss

There is significant interest in magnesium alloy castings because of their low density and high strength-to-weight ratio. Lightweight, structural materials are in demand for aerospace components, hand tools, electronics enclosures and have found increased use in automobiles. Increased use of magnesium will depend on the resolution of a number of materials issues and development of more robust and economical casting processes. Most magnesium components are produced via high-pressure die-casting. High levels of porosity generally prevent die-castings from being used for structural applications. Structural castings are usually produced using sand casting, a relatively expensive casting process. Some work has been done on development of lower cost structural casting processes, such as lost foam casting, permanent mold casting or low-pressure casting. New programs are also emphasizing improvements to the die casting process. Research and cost reduction needs are discussed with respect to current programs and future components.

Jan 1, 2006

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017