Search Documents

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By J. R. Johanson, A. W. Jenike

"A solid flows out of a bin provided that the outlet is sufficiently large so that stable obstructions to flow do not develop. The geometry and surface finish of a bin and the construction of the feeder determine the type of flow pattern which then develops within the bin. The pattern, in turn, affects the uniformity and consistency of the stream, segregation, caking, degradation, live capacity and the action of level measuring devices.In most bins now in operation, material flows toward the feeder through a channel which forms within the stationary solid. This is referred to as funnel flow. If the hopper of the bin is sufficiently steep and smooth and the feeder capable of drawing material across the whole area of the outlet, all the solid flows whenever the feeder is in operation; this is referred to as mass flow. Mass-flow bins are usually far superior to funnel-flow bins; their initial cost is also usually higher.The paper describes the design criteria used in deter-mining the minimum bin outlet needed for flow and the bin geometry needed for mass flow."

Jan 1, 1970

By W. R. Cowan

The Caledon Outwash is a large deposit of glaciofluvial gravel and sand located 55 km north west of down town Toronto. For the most part it was laid down in a meltwater channel fronting the Paris Moraine about 14,000 years ago. Applying the braided bar model of Eynon and Walker (1974) the principal facies present are imbricated coarse gravels (bar corefacies); crudely stratified, imbricated bar top sandy gravels; and trough crossbedded side channel sands and gravelly sands. Of lesser importance are crossbedded bar front gravels, shallow braided stream facies gravels, and stoss side facies sands and pebbly sands (rare). Lithologically these deposits are characterized by FIGURE I. Geological relationships of Caledon Outwash. Industrial Minerals in Canada up to 95% Ordovician limestone and siltstone in the gravel fraction. A siltstone content of up to 34% requires that beneficiation be carried out for the production of better quality aggregates. Resources remaining are estimated to exceed 500 million tonnes in 3000 ha of the most suitable part of the deposit. Present production is about 4.5 million tonnes per year, shared by several producers.

Jan 1, 1984

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

By H. V. Kinsey

"IntroductionTITANIUM is probably the most widely publicized metal today. Much has been written, both in the lay press and the technical press, about its properties and potentialities. In view of the fact that Canada possesses large quantities of titanium-bearing ore, and could conceivably become a major producer of metallic titanium, it was felt that a paper dealing mainly with the physical metallurgy of titanium would be of interest to this Institute. This paper is concerned chiefly with the useful properties of titanium and its alloys and the fundamentals governing the modification of its properties by alloying.Physical Properties of TitaniumTitanium belongs to a family of metals that have been termed 'gas sensitive' (I), because their mechanical properties are altered by certain gases which they readily absorb and retain. Other metals of this group are zirconium, hafnium, vanadium, columbium, tantalum, and chromium. Titanium has a strong affinity for oxygen and nitrogen and once it has absorbed these gases they cannot be removed either by melting in vacuum or by any degassing agent. These gases, when present in excess of about half a per cent oxygen plus nitrogen, render the metal brittle and useless as a structural material.Some of the typical physical properties of titanium are listed in Table I along with those of common structural metals for comparison."

Jan 1, 1953

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By Oy Leuangthong

The McMurray formation in the Athabasca oil sands deposits of Northern Alberta is part of the world?s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modeling of the McMurray formation using modern geostatistical techniques. Geostatistical modeling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: (1) assessing the most appropriate stratigraphic transformation for optimisation of the correlation structure, (2) determining representative distributions with declustering and debiasing techniques, (3) modeling spatial continuity of the bitumen grade, fines grade, water saturation and other petrophysical variables, (4) performing estimation and cross validation as checks against simulation results, (5) performing simulation for uncertainty quantification of bitumen and fines grade, and (6) model checking of simulation results against the input data and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed.

May 1, 2004

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By D. M. Baird

"Enormous deposits of gypsum of exceptionally high grade are readily accessible in southwestern Newfoundland. Coming large-scale production from one of these is resulting in renewed interest in deposits which have been known for more than a hundred and twenty years. General stratigraphy and structure of the Carboniferous rocks in which the gypsum occurs are de-scribed. The stratigraphic position of the basal gypsum-anhydrite zone is described. This massive evaporite horizon, which reaches a thickness of about 1,0001 feet, appears at Fishels-Heatherton, where it is largely undeveloped, and again on the nose of an anticline east of Flat bay, where a present production of 20,000 to 40,000 tons per annum is soon to be expanded to make it one of Canada's major producers. Detailed descriptions are given of the several types of gypsum, the relation of the gypsum and anhydrite, and the distribution of sodium chloride in the evaporite beds, and the bearing of all these on the origin of the gypsum are discussed. Brief reference is made to relation to world markets, mining and transportation, grade, and reserves."

Jan 1, 1959

By G. A. Pinsky, Pickard M. K

"IntroductionTWO METHODS of mucking have been used in sinking C shaft, the five-compartment production shaft of the Yellowknife property of Giant Yellowknife Gold Mines, Limited:(a) Band mucking during the original sinking in 1949 and 1950 (l); and(b) Mechanical mucking with the Cryderman shaft mucker during the recent deepening in 1954.This paper briefly describes the recent deepening and compares the performance figures of the two sinking operations.PlanningProduction planning in 1952 showed that it would be advisable to deepen C shaft in 1954 to provide for three new production levels and the installation of an underground crusher. To complete the required shaft work it would be necessary for a shaft crew to deepen the shaft about 500 feet, to partly excavate three level stations and a crusher station, and to cut a station for the loading pocket. Figure 1, a vertical section of the lower part of the shaft, shows the details of the deepening programme.During the planning period, Giant had a rather small supervisory staff and at the same time was experiencing a heavy labour turnover. As it was obvious that production would suffer if the sinking crew were recruited at the mine, it was decided that the merits of contracting-the shaft sinking to an independent contractor should be investigated."

Jan 1, 1955

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007