Search Documents

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners&apos; fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By Paykan Safe

?? Background ?? WorleyParsons Gas Cleaning ?? PT Inco Smelter ?? Process Design Considerations ?? Furnace Control and Combustion ?? Combustion Chamber ?? Spray Chamber ?? Draft Control ?? Baghouse ?? Secondary Ventilation ?? ID Fan ?? Dust Handling Equipment ?? Project Execution ?? Heat Recovery ?? Conclusion ?? WorleyParsons Gas Cleaning ? Irving, TX ?? Formerly Gas Cleaning Technologies ?? Acquired by WorleyParsons in 2005 and now part of a global EPCM company ?? 14 years experience in off-gas system design for ferrous and non-ferrous facilities worldwide

May 1, 2008

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT The influence of using different extraction processes (caustic versus non-caustic) on thethixotropic strength of oil sands fine tailings is examined, as is the influence of adding a coagulant tocaustic fine tailings. The thixotropic strength of fine tailings at large void ratios manifests itself as a bonding or gel strength that has been widely noted both in the laboratory and in the field. This gel strength has a significant influence on preventing the initial consolidation or settlement of fine tailings. Differences between the fine tailings’ thixotropic strength development are explained based on their physical and chemical characteristics.

Jan 1, 2010

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d&apos;asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l&apos;amiante peut offrir les performances souhaitées et l&apos;augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d&apos;une faible teneur en amiante courte il l&apos;enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C&apos;est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu&apos;on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991

By Jeff Stufsky

Debt Financing ?Broad Market Overview ? Recovering due to factors including: ? Increased trust in the system ? Enhanced capitalization of financial institutions ? The need to deploy capital for profit ? Competition: ? Investment-grade bond volumes increasing dramatically, and starting to pressure banks to compete with new capital ? Term Loan B financing from insurance companies and related institutions is returning, also pressuring banks to lend ? Local country financial institution capacity in Latin America has materially increased ? Results: ? Loan capacity increasing generally across instruments, regions, and sectors ? Financial institutions/banks starting again to seek yield as pricing competition heats up ? Tenors increasing with pricing coming down more slowly Underwriting is back in play

May 1, 2010

By T. Nyabeze

This paper presents the experiences and views of women involved in the mining industry as determined from a questionnaire that was circulated across the Canadian mining industry. Globally, there have been significant studies done to understand the historic and global variety of women?s participation in this industry1. The reason for focusing on women?s experiences here in Canada is because women?s percentage representation at 14.4% in the mineral industry workforce falls below the overall labour force average of 47.4%2. Notably, a recent article in the Globe and Mail newspaper points out that adequate representation of women in leading of organizations is more of a matter of competitiveness and innovation rather than purely a ?women?s issue?3. This paper will provide some insight into the reasons why women join and stay in the mining industry and shed some light into the reasons for the overall low representation in this sector. The authors believe, as stated in a study from the London Business School, that a gender-balanced workforce is one way of providing the best results in areas that drive innovation4. Women represent a key stakeholder group that can help enhance the mining industry?s sustainability through innovation. The women who responded to the questionnaire represent many different areas within the mining industry, including a broad range of roles in industry, government, academia and in the supplies and services sector. The paper is intended to raise awareness about issues that women encounter that contribute or detract from career satisfaction in the mining industry. The survey provides an overall understanding of why women pursue or work in mining, and why women either remain or choose to leave it. The advantages and disadvantages experienced by women are highlighted, along with a summary of the possible initiatives that could be undertaken by employers as opportunities to improve the attraction of the mining industry for career minded women. As well, the survey provides a summary of the top ten features that are already in place at various organizations and community groups that have been identified as key for supporting and encouraging women to join and remain in the industry. Not surprisingly, the survey identifies that one of the key ingredients for retention of women in mining is the provision of mentors and sponsors. Another key aspect for retention is the provision of progressive employment policies that address the need for a degree of flexibility in work hours and a culture of balance between work and personal life demands. The survey and results are portrayed only from a female perspective since it is largely women?s perceptions that will inevitably be transmitted to others who plan on entering the field.

Oct 1, 2010

By Matthew Scott

Introduction The refining of precipitate is the final stage of all the processes involved in gold mining and cyanide milling, by which the precious metal is at last obtained in a concentrated form, which can be accurately valued and marketed. Possibly one ought to say, conveniently shipped, for accuracy in valuation depends in many instances on a toughening treatment given the bars as received at the Mint so as to obtain a homogeneous metal that lends itself to representative sampling; which, of course, entails a surcharge on the regular Mint charges for the extra work necessarily undertaken. There are several methods of refining zinc-gold precipitate, each with its advocates; the method employed depending not always on the quality of the bullion produced but on the local exigencies of the case in point. These methods are more or less detailed in various textbooks and it is not the purpose of this paper to discuss them, but to confine ourselves to the specific case as stated in the title of the paper. At the outset, it behooves the writer to express his thanks to Mr. Brigham, the General Manager of the Hollinger Mines, for the kindly consideration and encouragement given in developing this process. This will be better understood when one considers the immense values involved, tending towards conservatism in practice, and making one chary of radical innovations. This process has been in satisfactory operation now for about two and-a half years, during which time over twenty-five million dollars value in fine gold has been produced, so that it may be reasonably held that the process is successful.

Jan 1, 1931

By J. A. Reid

THE views and observations expressed herein on this old but constantly recurring question are our own, no effort having been made to align them with standard texts. Therefore, while they may find general acceptance amongst fellow engineers, they must stand as personal opinions and as such are open to debate and discussion. In order properly to consider the subject, it should first be &apos;set in proper perspective. Why are Prospects Examined? Prospects are examined to determine whether they may contain economic concentrations of metals or minerals, the legitimate mining business being run, pretty largely, to make money. Next to food and clothing, modern civilization is based on metals, with which are included in this discussion minerals, oils, and fuels. A constant and increasing demand for the common metals requires the location of replacements for depleted orebodies, while the use and appreciation of new metals brings increasing demand for them. Aluminium is a good example of a metal which has, within recent years, made great progress. Today, we are becoming increasingly aware of magnesium, chromium, tungsten, thallium, and other lesser known, metals.

Jan 1, 1945