Search Documents

By B. N. Nandi

This paper is a study of the application of the science of coal petrology to the use of coal in the iron and steel industry. The petrography of coal is given the most attention, with some mention of coal palynology. The history of the petrographical analysis of coal is first out-lined, with a description of the various coal entities, and then the apparatus and experimental techniques employed for coal evaluation are discussed. The coke stability factor and the relation of coke strength to petrographical data are also covered, and some space is given to the new science of coke microscopy, in particular its use in following the oxidation of coals.

Jan 1, 1966

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Tai Sik Lee

Why ISRU into Space Exploration are important NASA and International Mission statements calls for the sustainable human exploration of the Moon, Near-Earth asteroids, and Mars Common Exploration Goals and Objectives are Strongly influenced by ISRU Extend Human Presence: Continually increase the duration and level of self sufficiency at all destinations Develop Exploration Technologies and Capabilities: Develop and validate tools, technologies, and systems that extract, process, and utilize resource to enable exploration missions Perform Science to Support Human Exploration: Characterize available resources at destinations Stimulate Economic Expansion: Encourage commercial services and create new markets, including markets for discovered resources Enhance Earth Safety: Test techniques to mitigate the risk of asteroid collisions with Earth

May 1, 2013

By J. Erik Scheel

Overview ? About Hard Creek Nickel ? Turnagain property ? Proposed power line ? Recent Preliminary Assessment ? Favourable economics ? Property Geology ? Mineralization and metallurgical characteristics of major lithologies ? Development of the acNi (ammonimum-citrate H2O2) technique ? Overview of necessary steps ? Results of the technique ? Conclusions

May 1, 2008

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

By V. G. Papangelakis, G. A. Moldoveanu

The use of anhydrite (AH) seed, control of acidity levels and ageing were assessed as means to promote the conversion of freshly produced metastable gypsum generated in-situ to the less soluble anhydrite phase and force deposition of calcium sulphate on seed as opposed to on equipment as scale, while achieving lower terminal aqueous calcium concentration as well. It was found that moderate sulphuric acid levels (0.25M) and ageing in the presence of AH seed accelerated the gypsum-AH conversion, achieving 100% transformation of the metastable gypsum generated in situ to the more stable, less soluble AH in 6-7 days, while lower/nil acidity did not promote more than 30% AH conversion for 10 days, even in the presence of AH seed. These findings indicate that anhydrite seeding, ageing and incomplete neutralization are beneficial for scale control as well as achieving lower calcium levels, thus rendering the resulting solution more amenable for recycling.

Jan 1, 2015

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By R. D. Mollison

"Ecstall Mining Limited was formed to operate the Kidd Creek mine, discovered by Texasgulf Incorporated in 1961 the orebody is geologically very complex, containing rich values of zinc, copper, silver and lead. The first phase of the operation involved an open pit, railroad and concentrator complex, which was under construction in 1965 and began operations in late 1966. The open pit, with rim dimensions of 2,000 by 1,000 feet, was computer-designed and highlights excellent wall control and efficient ore extraction and grade control. The railroad was built over the worst type of muskeg country, but it has been well maintained, resulting in an uninterrupted supply of ore in the trains. The 10,000-tpd concentrator, located 17 miles from the mine, is highly instrumented and automated. It features computer control of reagents and, in addition to the copper, zinc and lead flotation circuits, has a modern gravity tin plant. The concentrator is large, because very fine grinding is required for good metallurgy and nearly 2,500 tons per day of concentrates are produced. In 1969, work was started on the underground mine to take over from the open pit; it began partial production in mid-1973. The mine is highly instrumented, has a ramp from surface, a high-production shaft, an underground gyratory crusher and an efficient orehandling system, and employs the latest mining techniques. The electrolytic zine plant, rated at 120,000 tons of slab zinc per year, started operation in April, 1972, with batch leaching and purification circuits. It has been converted to continuous leaching and is now in the process of converting to continuous purification. Further modernization and automation will be carried out in the next few years. Five service departments support the five operating departments. These are maintenance, engineering and technical services, geology, administration and employee relations. How these ten departments function and work together using the most advanced technology to produce an efficient operation is the main theme of the Ecstall Story."

Jan 1, 1974

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

The bath level measurement is applied in many furnaces to keep control of the level of slag and metal or matte inside. The BLM is used mainly in bath processes, and has not seen much evolution in its basic functionality. For a closed DC FeCr furnace, special demands based on the furnace design and extreme process conditions were considered for the design of a bath level measurement in order to collect valuable information about the furnace operation. This paper will describe these demands and the solutions for them, followed by some of the uses for the BLM in a closed FeCr furnace. Some of the future developments on the BLM conclude this presentation.

Jan 1, 2015

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940

By J. Lee

As the usage of BIM increased in the construction industry, some construction owners started exploring the use of BIM for maintaining their facilities. Construction Operations Building Information Exchange (COBIE), a spreadsheet data format suggested in 2007 to manipulate building information, is considered as one of the solutions that would facilitate the process of transferring information from BIM to applications for facilities management. Several BIM and Computer Aided Facilities Management (CAFM) applications offer functions to export or import the COBIE data. To facilitate the process of generating the COBIE data out of Building Information Model, some add-in applications, such as COBIE Toolkit for Revit, also were developed. However, most of these applications handle a limited amount of COBIE data. Professionals using these add-in applications therefore sometimes end up spending a significant amount of time to add additional data manually to the COBIE data file. To automatically get a data-rich COBIE file, we developed a prototype application that extracts information from Revit, which is one of the BIM authoring tools, stores them in an external database, and then produces the COBIE file using information stored in the database. We applied our application to a pilot project and produced 8 COBIE worksheets automatically, which demonstrated a significant amount of time saving. This paper presents how our prototype application produces 8 COBIE data sets automatically. It also addresses our attempt to handle more COBIE data sets.

Aug 1, 2013

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014