Search Documents

By R. D. Brown

"Finance Minister Donald Macdonald's budget of May 25, 1976 featured a restructuring of the anti-inflation profit controls and a grab bag of tax changes, some of direct interest to the mining industry. All Canadian taxpayers now will be permitted to write off immediately 100% of mineral and oil and gas exploration expenses included after• May 25, 1976 and before July 1 1979. The cost of acquitting Canadian resource property after May 6, 197.4 from a federal or provincial government will now clearly be included in Canadian development expense, and provincial drilling and exploration incentives received after May 25, 1976 will not reduce exploration and development expense for federal income tax purposes. Under tough new anti-inflation profit controls, all controlled businesses, except distributions, will essentially have one uniform set of rules for• determining allowable profit margins; this allowable margin will be determined by product line or by over-all net margin and will be 85% of the higher of the margin obtained in the five years preceding October• 13, 1975 or the one year preceding May 1, 1976. The basic capital cost allowance system is to continue, but many rates will be revised. The ability to offset losses created through claiming capital cost allowances on leased equipment, etc. against other income will be ended with respect to transactions entered into a/te1• budget night. Miscellaneous other tax changes will raise the low rate base for Canadian-controlled private corporations to $750,000 increase retitement plan contribution limits and reduce the rate of branch tax imposed on branches of corporations resident in a country with which Canada has a comprehensive tax treaty to equal the withholding tax rate on dividends under that treaty."

Jan 1, 1976

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By A. Gauthier, J .. E. Muir, M. Cormier

Falconbridge's Lac Shortt gold deposit is located in Gand Township, some 25 km north-east of Desmaraisville, The deposit was outlined in i980 by a drilling program me conducted by Falconbridge Ltd. in a joint venture with Corporation Falconbridge Copper after three years of systematic exploration by Falconbridge Ltd. in the Desmaraisville area. The gold bearing structure had previously been drilled by three other exploration companies. As based on an underground development programme conducted by Corporation Falconbridge Copper, the "in-si tu" mineral inventory to a depth of 500 metres at a cut-off grade of 3.0 g/t is estimated at 1 937 605 tonnes at a grade of 6.4 g/t (uncut) and 6.0 g/t (cut). Regionally, the stratigraphy consists of thick sequences of volcanic and volcanosedimentary rocks intruded by numerous and voluminous mafic (gabbro), felsic (granodiorite, syenite) and anorthositic intrusions. Structurally, at least two fold sets and one major fault system (E-NE) are present. Minor fault systems oriented E-NE and N-NW also occur. Mine stratigraphy can be divided into 1) - the hangingwall; 2) - ore zone; 3) - footwall. Hanging wall rocks include: a) green lapilli and blocky tuff b) transition zone c) green mica crystal tuff and d) red dolomitic tuff. Ore zone rocks include: a) bleached mafic tuff b) barren carbonates, c) pyritic dolomitic tuff (?) and d) brick-red syenite. Footwall rocks include: a) magnetic lava (so-called diorite), b) mafic lapilli and blocky tuff and c) alkali basalt, Native gold is the only gold mineral so far identified and it occurs both as free grains in gangue and as micro-inclusions in pyrite. Two geochemical groups were identified in the main rock units: 1) Alkali-rich rocks cons is ting of the ore zone and foot wall rocks and 2) Subalkaline group consisting of the hanging wall rocks. Ore analysis also shows Ba, Sr, W, Zr, REE and F enrichment in the ore zone. Footwall rocks are enriched in Na20. Present geological and geochemical data do not permit a clear interpretation of the formation for the Lac Shortt gold deposit but suggest it is a volcanic-hosted stratabound type. The bulk of the mineralization is associated with an exhalative phase following alkalic, carbonic, hydrothermal activity and part of the mineralization is associated with a late intrusive phase.

Jan 1, 1984

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By K. J. Aglias, M. Jeffery, J. V. Simmons, J. A. Johnston, S. G. Fityus

"Shales and mudrocks undergo weathering in the near-surface geological environment, and degradation when directly exposed at the surface. Despite having superficially similar appearances, many shales have very different degradation behaviours. For example, some shales break down readily upon exposure whilst others remain more or less intact. Further, for those shales which break down, the style of degradation can vary greatly. A phenomenon is described where fresh shale blocks that are exposed at the surface undergo rapid breakdown to a fragmented texture which then persists for relatively long times, without further breakdown to finer soil particles. This is illustrated for some coal mine waste rocks. Furthermore, this metastable fragmented texture seems to be particular to each particular type of shale. The paper presents a conceptual model for this physical breakdown of shales which accounts for the differences in fragmental texture that are observed. The importance of several factors including strength, permeability and expansive clay content are identified for their contribution to the degradation behaviour of different shales.INTRODUCTIONShales and MudrocksThe term shale is applied widely to a class of mudrocks having a range of distinctive but gradational appearances and mechanical behaviours. Mudrocks are sedimentary rocks primarily composed of silt and clay sized particles (Tucker 1982). Mudrocks form in low to very low energy environments such as flood plains, lakes and deltaic environments, where the finest detrital particles are able to settle out of suspension (Reeves et al., 2006; Stow, 2005; Tucker, 2001).Unlike coarser siliciclastic sedimentary rocks, mudrocks do not present with a wide variety of sedimentary structures and textures. The most common texture is a preferred orientation of clays and micas parallel to the bedding plane. This textural component is related to the property of fissility or the ability for such textured mudrocks to split along smooth planes that are parallel to the bedding. Another common structure is lamination, formed by variations of grain sizes and types during deposition, Massive texture describes the situation where no sedimentary structures or textures are apparent (Boggs Jr., 2009; Tucker, 2001). The term shale varies between sources and contexts, with Reeves et al. (2006) stating that a shale is a fissile mudrock, where “fissility is a property that has developed at a certain stage of weathering”."

Jan 1, 2015

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By F. J. MacPherson, A. C. Caron

"Cassiar Asbestos Corporation Limited is at present B,C.'s only asbestos mining company, and has been actively engaged in the management and operation of the Cassiar Mine since the early 1950's. The Cassiar operations are located between 3,500' and 6,600' elevation in a secluded mountainous area of northern B.C., approximately 100 miles by road southwest of Watson Lake in the Yukon Territory. Climatic conditions in this area range from mild warm in the summer, to extremely cold during the long winter period.The minesite itself is located over a mile above sea level at the top of McDame Mountain, where year round 24 hours per day miners extract the chrysotile ore from the surrounding waste by standard open pit techniques. The ore body dips into the mountain at about a 45° angle, and as the mining progresses, larger stripping ratios are required. Waste to ore ratio this year will be more than 10 to l whereas only a few years ago ratios of 3 or 4 to l were possible. After drilling, blasting, and loading by shovel onto trucks, the asbestos ore is transported to the Primary Crushing Plant for crushing prior to transport by aerial tramway more than three miles to the Concentrator and Mill in the valley below, where the fibre is extracted from the barren host rock serpentine and milled into numerous grades for shipment to asbestos users round the world. The major air usage is associated with the milling process, presently requiring over 500,000 CFM, with future requirements expected to exceed 840,000 CFM by the end of the decade."

Jan 1, 1976

By Anoop Sattineni

Over the past decade the use of BIM in the AEC industry has grown several fold and with it the number of standards available for implementing BIM. The ?National BIM Standard? by buildSmart Alliance, the ?Contractor Guide to BIM? by the Associated General Contractors of America, the ?BIM Project Execution Planning Guide and Templates? from Penn State University, the ?BIM Roadmap? by the US Army Corps of Engineers are some of the several BIM guidelines that are currently available to the AEC industry practitioners. Some of these guidelines are as comprehensive as defining BIM and the associated taxonomy while others are meant to be used on an individual project basis. From a contractor?s perspective one of the key benefits of using BIM is for the purpose of collision detection and coordination. This research has found that currently available guidelines do not address these issues adequately. For instance, the currently available guidelines do not allow the subcontractor to quickly communicate issues such as naming conventions and color schemes within the model, to the general contractor. Consequently general contractors and sub-contractors find themselves making changes to their BIM deliverables based on each other?s abilities and levels of adoption, apart from reason?s stemming from use of different software platforms. This paper describes how a group of contractors and subcontractors from Atlanta and Birmingham in the United States came together to create and adopt a ?Coordination Guidelines for Virtual Design and Construction?. These guidelines were specifically created with the purpose of streamlining the construction coordination process using BIM. This paper describes how the guidelines created differ from other guidelines currently available in the industry.

Aug 1, 2013

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By A. Dunnett, N. J. Turner, J. Koyanagi, M. Ji

The analysis of rare earth element (REE) samples is a necessary part of the metallurgical process for rare-earth bearing ores, providing invaluable information during testing procedures. This requires a fast, multi-element technique, capable of analyzing a variety of matrices for all rare earth elements. X-ray Fluorescence spectrometry and Instrumental Neutron Activation Analysis are typically used for high concentrations of REE, but they have limitations for some process work applications due to an inability to measure all elements, longer analysis times, significant interferences and elevated detection levels. The work reported here uses new approaches with Inductively Coupled Plasma Mass Spectrometry (ICP-MS) in order to achieve high precision and accuracy within acceptable timeframes. A combination of aerosol dilution and Kinetic Energy Discrimination (KED) produce a process solution assay method that is robust enough to deal with changing sample matrices and concentrations, whilst maintaining low reporting limits and precisions of less than 5% Relative Standard Deviation (RSD). For high concentration metallurgical and geological samples, a sodium peroxide fusion digestion procedure was used, followed by ICP-MS analysis using extended dynamic range (EDR) and KED. Using these technologies, it has been demonstrated that the necessary support can be given to metallurgical process work for REE extraction.

Jan 1, 2014

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By F. Roemer, D. Goldmann, T. Elwert

Tantalum is an important minor metal for the production of high performance capacitors. Approximately 60% of the annual tantalum production is used in this application. Despite its high price of 298 US$/kg (average price 2010–2014), at the moment, no recycling from end-of-life products takes place. In the established recycling processes of waste electrical and electronic equipment (WEEE), tantalum is lost in the slags of copper smelting, where it is highly diluted. An economic recovery is not possible at that point. Although tantalum must therefore be extracted from the WEEE stream before it enters smelting, no industrial recycling processes exist. The main reasons are its low concentration in the WEEE stream, lack of information about tantalum bearing devices, technical difficulties of extraction, and conflicts of interests regarding the recycling of other valuable metals in WEEE. In this paper, the results of a cooperation research project are presented. The aforementioned challenges are addressed and a novel tantalum recycling process is developed. Small pilot scale experiments show that a mechanical processing route can produce marketable tantalum-concentrates of 30% tantalum with yields between 60 and 70%. This is reached through a manual pre-sorting of potentially tantalum bearing products followed by a combination of an optimized comminution, sieving, air classifying, eddy-current (EC), and two stage magnetic separation. Key to the implementation of this process was a detailed survey of the tantalum concentrations in different products carried out by the industrial partner.

Jan 1, 2016

By Z. Y. Liu

A local additional potential model (LAPM) was developed to illustrate the role of strain rate in stress corrosion cracking (SCC) of pipelines. According to LAPM, both density and mobility of the local active spots on the steel surface, i.e., dislocation emergence points, increase linearly with strain rate. Generation of such active spots introduces an additional negative potential locally, affecting the electrochemical reaction and, consequently, the susceptibility of the steel to SCC. Electrochemical corrosion measurements, slow strain rate tests and electrochemical hydrogen permeation test were combined to demonstrate the validity of LAPM to illustrate pipeline SCC in an acidic soil solution. It is found that a maximum of the SCC susceptibility occurs at strain rate of 10-6 s1, which is associated with an enhanced hydrogen evolution due to the local additional potential (LAP) effect.

Jan 1, 2010

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By R. G. S. Mussi

An inclined cooling plate is utilized as a modification in the compocasting process of magnesium alloy and the mechanical properties of the composites obtained are studied in this work. Based on crystal separation theory, molten AZ91D is poured onto an inclined plate in order to produce solidification nuclei inside the fluid metal, and is mechanically stirred while reinforcement is added. Particulate SiC was utilized as reinforcement in quantities varying from 0 to 15%vol. Dispersion of the reinforcement was observed by macro and microstructure analysis. SiC was properly mixed into matrix until 15%vol., and Vickers hardness tests were carried out for the composites produced. Results obtained for hardness were shown to increase with reinforcement addition and comparable to those of traditional compocasting. Utilization of Inclined Cooling Plate produced good inclusion and homogenization of SiC through an AZ91D matrix, at lower temperatures and shorter times than traditional compocasting.

Jan 1, 2006