Search Documents

By J. S. Redpath

There appears to a definite trend toward the hoisting of greater tonnages from greater depths. There is every indication that this trend will continue and we feel that improvements in the design, fabrication and installation of mine guides will be of significant importance in the future. The present state of the art in mine-shaft guide systems is reviewed and the parameters required for improvement are derived in this paper. Finally, a proposal is made for a new steel guide system which meets the parameters and is economical to fabricate and install.

Jan 1, 1977

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By Ellie Condolios

Hydraulic hoisting offers a number ~f attractive features over conventional hoisting methods: small shaft space requirements; great flexibility of layout, including pick-up or delivery of the material at points distant from the mine shaft; low investment and operating costs. However, limited practical experience with this type of hoisting dictates that careful design and, frequently, extensive testing be done by competent engineers before large-scale installations are built. This paper covers the following: basic laws and design criteria for hydraulic hoisting installations; a description of a coal hoisting installation which has been in industrial operation since 1960, with a vertical lift of 600 feet and an annual capacity of 500,000 tons of -3 ~-in. coal; and a tentative appraisal of the process, including cost estimates. THE transportation of solids in water flowing through a pipe-line has, for a number of years, been common practice in dredging, public

Jan 1, 1963

By G. Azimi, K. K. Varanasi1, A. T. Paxson, R. Dhiman, H. -M. Kwon

Hydrophobic materials that are robust to harsh environments are needed in a broad range of applications. Although durable materials such as metals and ceramics, which are generally hydrophilic, can be rendered hydrophobic by polymeric modifiers, these materials deteriorate in harsh environments. Here it is shown that a class of ceramics comprising the entire lanthanide oxide series, ranging from ceria to lutecia, is intrinsically hydrophobic. Their hydrophobicity is attributed to their unique electronic structure, which inhibits hydrogen bonding with interfacial water molecules. In addition, this work demonstrates that these ceramics sustain hydrophobicity even after exposure to high-temperature environment (1000 °C for 2 h in air). It is envisioned that this class of robust hydrophobic materials will have far-reaching technological potential in various industrial applications, where water repellency and dropwise condensation are desirable.

Jan 1, 2014

By H. R. Banks

SHORTLY after the commencement of operations at the Sullivan concentrator, the use of a pilot table was instituted in order to present a visual control of various products by showing the amount of galena still present in the tailing from several stages of flotation. Among the products so treated, the final tailing was later included. It was sratifying to note that very little free galena was escaping, but a fine streak o a whitish mineral appeared at the concentrate zone. This mineral was identified as cassiterite. The amount was small and the newly recognized component in an already complex ore was considered primarily as of academic interest. However, the problem of recovering a usable metal was intriguing and, as opportunity presented itself in temporary lulls in research on Sullivan and other ores, the concentration of tin was a useful 'bit of knitting' to go on with. It was recognized from the start that the bulk of the mill tailing would have to be floated and the residue subjected to gravity treatment. Since one of the predominating features of Sullivan concentration operation has been the necessity of fine grinding, the problem of gravity concentration was thereby intensified. Several batch runs were made, and sufficient pulp was treated to produce about one ton of final tin concentrate assaying 67 percent tin. The overall recovery was under 30 percent and the estimated profit at full tonnage was only marginal. Testing was resumed several years later, when the price of tin again appeared attractive, in an attempt to develop a more compact plant with better recovery of tin. The weakness of the original plan of concentration was the large number of tables required to treat a feed so low in tin.

Jan 1, 1941

By D. C. Downing

"I THANK YOU for the invitation which The Mining Society of Nova Scotia extended, originally to Gordon Berry, manager 'of our Point Tupper Refinery, to join you at this meeting and discuss refining and petrochemicals in their relation to this region. There are natural advantages in Nova Scotia which have made possible, and will continue to make possible, sizeable developments both in petroleum refining and in chemicals. Equally, however, as is the case everywhere, there are certain constraints. For clarity in this presentation, I will state some of these constraints right at the beginning. First, of any future developments from now on, only a small proportion of the products can be expected to go into local markets. I can make the point best with a few figures. Petroleum companies all have market forecasts. None ever work out to be perfect, but the trends are relatively predictable and the orders of magnitude are certainly correct. Estimates for the use of all refined petroleum products in the four Atlantic provinces are:"

Jan 1, 1973

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By A. J. Neale, B. C. Flintoff

"In most mineral processing operations the term audit is usually reserved for the exercise of checking financial records and/ or safety practices. While these activities are time consuming, no one disputes their necessity or value. If we subject these areas to such careful scrutiny, why is it that we don't normally apply the same principles to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance, in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focused manner. Experience teaches us that the exercise is very revealing and potentially very rewarding.This paper will discuss the process audit process and illustrate its potential value through illustration taken from plant studies.IntroductionThe last twenty years have seen tremendous technological and organizational changes sweep the minerals industry. Process control systems, on-stream analyzers, and gold recovery techniques barely conceived twenty years ago are now incorporated in virtually all new installations in an effort to maximize operating efficiencies. In conjunction with these developments, changes in the way plants are managed, down-sizing of technical staff, reduction in the size of operating crews, and the flattening out of the management structure have significantly reduced operating costs. As a result, plants are making more efficient use of our natural resources, minimizing the costs of production, and in turn maximizing operating profits. Or are they?"

Jan 1, 1991

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001

By Charles Graham

It is the general belief that the coal deposits on Vancouver Island are extremely large, and easily available. Indeed, they are frequently described by prominent public men and by writers in the press as "illimitable" and "inexhaustible." It is well that the facts that have been established as a result of seventy years of surface prospecting, underground operations and extensive diamond-drilling in this coalfield should be disclosed. HISTORY The presence of coal on the coast of British Columbia was first made known by Dr. W. F. Tolmie in 183 5. This coal was brought to him by Indians from the north-east coast of Vancouver Island, probably from Suquash. In 1850 the existence of coal at Nanaimo was announced by Mr. ]. W. MacKay. Development was started in 1852, and coal was shipped before the close of 185 3. The first operations were carried on by the Hudson's Bay Company, who operated the mines until 1861, when they sold them to the Vancouver Coal Mining and Land Company. Practically all of the operations in the immediate vicinity of Nanaimo have been carried on by this Company and its successors. In 1869, Mr. Robert Dunsmuir discovered coal about five miles north-west of Nanaimo, at Wellington. The Welling-ton Colliery Company was organized, and began to produce coal from the Wellington mines in 1871, the coal being shipped from Departure bay. This colliery was a large producer for several years, but was finally closed in 1900.

Jan 1, 1924

By A. M. Richmond

Introduction The apparent commonplace, and prosaic, nature of building-stones, lime, cement, gypsum, and clay products, and many other miscellaneous non-metallic minerals, such as abrasives, barite, diatomite, magnesite, mica, slate, salts, etc., and their everyday appearance and necessary in our lives, has removed much of the glamour, romance, and speculative attractiveness so frequently associated with our gold, silver, lead, zinc, and copper mining ventures. However, it will be readily appreciated, with but a brief study of the thirty-five or more non-metallic minerals and products which are mined, prepared, or are known to occur, in British Columbia, that the 'industrial minerals' industry in the Province has an abundance of interesting technical problems, is fraught with speculative possibilities, and, as such, fully deserves much more technical attention than it has hitherro received. The brief notes presented in this paper show, in summary form, the magnitude of the British Columbia industrial and non-metallic mineral industry; outline in synoptically form the principal deposits of non-metallic minerals presently known; and indicate in a general way a few of the possibilities which exist in the Province for the expansion of the industry. For convenience in presentation, the assembled material has been divided into four sections: 1.-Sraristical information 2.-Strucrural non-metallic minerals 3.-Miscellaneous non-metallic minerals 4.-Non-Metallic mineral possibilities in British Columbia 1. -Statistical Information The writer does not propose to dwell at length on the statistical comparisons and deductions which may be drawn from the four tables which have been compiled for this section of the paper, nor is it considered essential, as the figures present a most emphatic story in themselves.

Jan 1, 1935