Search Documents

By S. Caron, P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. However, over the last decade, Discrete Element Method (DEM) modelling has shown an interesting potential in describing the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics, and in developing solutions to industrial practice. With the objective of bringing this modelling technology into the concentrator control room to assist operators, this paper aims to describe the main elements needed to apply this emerging and developing technology to on-line mill performance monitoring.

Jan 1, 2004

By Andrew Popko

Introducing EnCana ?? A leading North American Oil and Gas company ?? Focused on natural gas and oil sands development in 12 key resource play areas across North America ?? In 2007, over 4300 wells drilled, producing about Enterprise value of approximately $50 billion ?? Invest between $5.8 Billion in 2007 ?? Over 7500 employees ?? Headquarters ? Calgary, AB

May 1, 2008

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005

By C. J. Van Treeck

PGE concentrations of 18 g/t occur in the pyroxene rich rocks at the Union Bay Alaskantype complex. This PGE enrichment is hosted in magnetite veins. These veins cross magmatic layering and have an irregular morphology in both outcrop and thin section. Fe-Ti oxide geothermometry suggests that this mineralization took place between ~700-400°C. A variation in the amount of ilmenite and Mg- Al spinel exsolution in magnetite correlates with temperature estimates, lower temperature magnetite has less exsolution. Hydrous silicates form an alteration envelope around magnetite veins with a formation temperature of <575oC, vary with temperature, and contain appreciable amounts of Cl. Interaction of a PGE-Fe-Cl rich fluid with clinopyroxene increased the fluids pH and decreased PGE and Fe solubility depositing a PGE enriched magnetite within the Pyroxenites and Olivine Pyroxenites of the Union Bay complex.

May 1, 2003

By Roberto Busato Belger

- Fertilizer Business Overview - Supply -Demand Balance in the World - Supply -Demand Balance in Brazil - Brazilian Market Growth Opportunities - Fosfertil Operations - Fosfertil Expansion Plan - Salitre Project - Project Characteristics - Technical Challenges and Solutions - Technical Support Studies Conclusions

May 1, 2010

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

By R. Gallinger, B. Kelley

"In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale.The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP’s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed assufficient justification for the formation of INAP.INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage.This paper will explore the international efforts and activities of INAP."

Jan 1, 2005

By R. Gallinger

In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale. The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP?s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP

May 1, 2005

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By Donald Leroux, Lori Lynn Smith, Robert Hutchison

"The grinding circuit of the Heath Steele concentrator was sampled under five different sets of operating conditions. The balanced results of the sampling campaigns were used to calibrate steady-state rod mill, ball mill and cyclone models using a commercial simulation software package (JKSimMet® ). Thirteen process variables had the potential to affect significantly the performance of the grinding circuit. Statistical-Design-of- Experiments techniques were applied to plan the suite of simulations in order to improve the quality of and minimize the time to find the optimal solution. The effect of each factor on three performance indices (the cyclone overflow size distribution, the circulating load and the cyclone underflow density) was modeled with empirical polynomial relationships using another software package (Design-Expert@)T. he conditions under which the cyclone overflow size distribution was maximized while respecting circulating load and cyclone density constraints were identified using these relationships. Among the most interesting results is the prediction of a set of conditions where the circuit target size distribution is achieved with only three ball mills instead of four.IntroductionProduction at the Heath Steele concentrator (near Miramichi, New Brunswick) started some 43 years ago at a rate of 750 t/d. The plant capacity was increased to 4000 t/d through successive expansion phases in the seventies (Sapiro, 1977; Johnston, 1978). However, as a result of depleting ore reserves, the plant throughput had to be gradually reduced to the current production rate of 2700 t/d. Heath Steele Mines currently have proven and probable reserves which would see it producing until the end of 1999 (Noranda Inc., 1997).An analysis of the grinding circuit of the Heath Steele concentrator was recently commissioned to identify opportunities for reducing operating costs while maintaining budgeted mill throughput and metallurgical performance. Since the plant will likely be operated below nominal capacity for the rest of its lifetime, the possibility of improving grinding efficiency by operating with fewer ball mills and/or crushers was contemplated."

Jan 1, 1999

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By Ward E. Kilby, Bruce I. Mcclymont

"Data from the South Fork Pit Area of the Bullmoose deposit in northeastern British Columbia are used to demonstrate the usefulness of microcomputers to the on-site geologist. The technique utilizes a series of digital surf aces in the form of a network of points to define various geologic parameters such as seam positions, topography and coal quality characteristics. Manual digitizing, kriging and combinations of these techniques are used to calculate these digital surfaces, the best method depending upon the type and quality of the data in question. Digital surfaces, each modelling a specific feature when combined and manipulated with the computer form a powerful tool, the deposit model. The resultant model, containing all the surfaces, is used to examine seam and inter-seam thicknesses, deposit volumetrics, seam quality characteristics and the adequacy of sampling.IntroductionCoal deposit modelling using computer-based techniques has become routine. However, a geologist working in the field, without access to mainframe or minicomputer, ha s considerable difficulty implementing these procedures. However, microcomputers, which are portable and inexpensive can handle exploration data, perform various geological analyses, and produce deposit models virtually at the same time as the data is being collected. For the on-site geologist this means that quick access to the results of such modelling could point out inadequacies in deposit definition and trends in coal quality deserving investigation."

Jan 1, 1985

By J. Petit, P. Girard, A-M. Gilbert, D. Faucher

L&apos;annee 2000 a été une année stratégique et significative pour l&apos; Aluminerie de Bécancour dans la réduction des gaz a effets de serre. L&apos; équipe s&apos; etait donne comme defi un jour d&apos;arriver a l&apos;objectif de zero effet d&apos;anode dans les sa11es de cuve (720 cuves au total). Le cha11enge s&apos;averait tres ambitieux car la fa<;on d&apos;alimenter une cuve d&apos;electrolyse pour obtenir son maximum de rendement faraday est de travailler le plus pres possible de l&apos;effet d&apos;anode pour eviter l&apos;embourbement de ce11es-ci. Ceci signifie que techniquement nous a11ons en moyenne, quotidiennement, 12500 fois pres de l&apos;effet d&apos;anode sur !&apos;ensemble de nos 720 cuves qui produisent aujourd&apos;hui environ 405 000 tonnes d&apos;aluminium liquide annuellement. Des 695 kg equivalent en C02 par tonne d&apos;aluminium produite en moyenne annue11ement, de 1990 a 2000, nous en sommes rendus ace jour a environ 35 kg equivalent en C02 par tonne produite. Nous sommes pres d&apos; atteindre notre objectif mais les demiers gains sont plus difficiles a atteindre. Les strategies d&apos;automatisme et d&apos;informatique, incluant l&apos;aspect de !&apos;implication humaine sur les bonnes pratiques de travail sur les cuves d&apos;electrolyse, sont les cles de ces resultats.

Jan 1, 2006

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

By Stanley G. Hutton, Robert Brubaker

"It has long been recognized that mining workers subjected to high levels of hand-transmitted vibration may suffer from vibration-related complaints. Prolonged exposure to whole-body vibration may also result in adverse effects. In this study, the effects of vibration on mining workers are examined. Previous work documenting the occurrence of vibration-related disease is reviewed. From this work, it is apparent that operators of hand-held pneumatic rock drills are exposed to a significant risk of developing vibration disease. Vibration levels recorded on the rock drills now in use are presented and shown to exceed levels recommended by a proposed ISO standard.IntroductionThe possible harmful effects of exposure to excessive vibration levels have long been recognized, particularly among operators of hand-held tools. Numerous cases have been reported of a vasospastic disorder commonly known as vibration white finger disease (VWFD), which was a term coined by the Industrial Injuries Advisory Council in Scotland in 1970(1 ), Those suffering with the disorder have frequent vasospastic attacks in which the fingers, hand and, in advanced cases, the lower arm turn white and numb, usually after a cold stimulus. Advanced stages of VWFD have been reported in which the skin becomes ulcerated and gangrenousm. The incidence of the disease has been particularly serious in the forest industry due to the extensive use of chain saws. However, in recent years, the introduction of antivibration saws has resulted in a significant reduction in the occurrence of the disease.In a recent report for the Canadian Department of Supply and Services - Energy, Mines and Resources, Hutton & Brubaker considered the effects of vibration on workers in the mining industry. In this report, the physiological and medical effects of vibration were considered, relevant vibration standards were discussed, previous vibration measurements were documented and field measurements carried out. In the present paper, the results recorded in this study will be summarized, together with results that have been previously published relating to vibration levels existing in the mining industry."

Jan 1, 1982

By J. G. Peacey, G. Csicsovszki

The target of this study was to clarify the role of lead on the dissolution of gold in the (NH4)2S2O3-Cu leaching system via chronopotentiometry, linear sweep voltammetry and chronoamperometry. It was found that the dissolution of gold was significantly increased with lead concentration up to 10 mg/1 Pb in the system of 0.1 M (NH4)2S2O3 and 50 mg/1 Cu. \/oltammograms suggested that the anodic dissolution of gold was virtually independent of lead concentration in the range of 1-10 mg/1 in 0.1 M (NH4)2S2O3 solution while in solutions containing copper as well, addition of lead increased the anodic dissolution of gold.

Jan 1, 2011

By Jim Richard

Introduction Electric Vehicle Controllers (EVC) and the Northern Centre for Advanced Technology (NORCAT) have created two generations of Lunar Highland Simulant ?Simulant preparation techniques and equipment resulted from drilling activities in support of Regolith and Environment Science and Oxygen and Lunar Volatiles Extraction (RESOLVE ) ?The purpose of defining the compaction process was to minimize the effect of density on drill testing This allowed other variables including drill bit geometry, auger, RPM, and thrust to be evaluated independent of density ?Density of Highland Regolith falls within a range of 1.40 to 2.29 g/cm3 (p484 Lunar Source Book)

May 1, 2013