Search Documents

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By Denis Racicot

"L'Abitibi québécois a produit essentiellement de l’or, du cuivre, du zinc et de I' argent, ainsi que de faibles quantités de nickel, de plomb, de molybdène, de bismuth, de lithium, de fer et d’amiante. Depuis l’ouverture de la mine Horne en 1927, cent-cinquante mines ont contribué à la production de 1 420 tonnes d’or de 4,1 millions de tonnes de cuivre et de 4,7 millions de tonnes de zinc. Les productions minières annuelles ont été d'importance variable: des records de production ont été établis en 1955 pour I' or avec 35 tonnes et, vers 1965, pour le cuivre, le zinc et la quantile globale de minerai extrait avec respectivement 130,000, 275 000 et 13 millions de tonnes. Deux dépressions généralisées ont eu lieu, l’une vers 1946 et l'autre, a lafin des années soixante-dix. Des ralentissements de la production ont été observes pour le cuivre en 1953 et le zinc en 1959. Depuis le debut des années quatre-vingt. I' or et, de façon plus irreguliere, le zinc sont en progression, landis que le cuivre, malgre une hausse en 1983. pour suit son dec/in.La teneur de récupération des mines d’or est demeurée régulière et n’a subi qu’une faible diminution au cours des quarante dernières années. Célie du cuivre a diminué d'environ 50% dans la même période, landis que celle du zinc a subi d’import antes variations, aussi bien positives que négatives. Près des trois quarts des mines d'or ont une durée de vie inférieure à 12 ans et la distribution des tonnages de minerai extrait montre un maximum pour la classe de 100 000 à 1 million de tonnes. Du cote des mines de métaux de base, la durée de vie est plus étalée et les volumes de minerai ont une occurrence maximale dans la classe de 1 à 10 millions de tonnes.Concernant la distribution géographique de la production minière dans l'Abitibi québécois, le camp minier de Rouyn-Noranda vient en tête pour l’extraction de minerai et la production d’or et de cuivre. L’est sui vi par le camp de Val d'Or pour le minerai et l’or, landis que le camp de Chapais-Chibougamau occupe la deuxième place pour le cuivre avec une production équivalence a 60% de celle de Rouyn-Noranda. Le camp de Cadillac-Malartic suit de tres pres celui de Val d'Or pour ce qui est de I' or. Finalement, dans le casdu zinc, le camp minier de Joutel-Matagami domine largement avec une production qui a connu un développement accélère depuis 1963. Une analyse pré liminaire de ces données indique qu' i/ subsiste unpotentiel encore élevé de production d'or, décuivre et de zinc dans I' Abitibi québécois. ABSTRACTThe Quebec portion of the Abitibi belt has essentially produced gold, copper, zinc and silver, as well as some small quantities of nickel, lead, molybdenum, bismuth, lithium, iron and asbestos. Since the opening of the Horne mine in 1927, one hundred and fifty mines have produced 1420 tons of gold, 4,1 millions tons of copper and4,7 millions tons of zinc. Annual mine production has fluctuated: production records were established in 1955 for gold with 35 tons, and around 1965 for all extracted ore copper and zinc with respectively 13 millions, 130 000 and 275 000 tons. Two main recessions have occurred, the first around 1946 and the second during the late seventies. Cut backs in copper and zinc production occurred in 1953 and1959. Since the beginning of the eighties, gold production and to a lesser extent zinc production have been in progression. Except for a small jump in 1983, copper production is still declining.The average recuperation grade of gold mines has been quite steady and has only slightly diminished in the past forty years. The average copper recuperation grade was halved during the same time interval. For zinc there have been important ups and downs. At least three quarters of gold mines have an average lifespan of 12 years the tonnage distribution shows a peak in the 100 000 to 1 million tons class. Base metals mines show a more widespread life expectancy and have a tonnage peak in the 1 to 10 millions tons range"

Jan 1, 1990

By J. Davis, M. G. Reading

"INTRODUCTIONInternational Minerals and Chemical Corporation (Canada) Limited operates two potash mine/refinery complexes near Esterhazy, Saskatchewan. Annual production of approximately 4.2 million tons is sold in the United States and overseas in five grades according to size and quality.Ore grading 25% K2 0 equivalent is mined from a horizontal bed by continuous boring machines, crushed, and hoisted at 8 inches. The refinery operation consists of the eight basic steps shown in Figure 1. Particle sizes handled are similar to those experienced in other forms of mineral beneficiation: 8 inches to 100 mesh. The ore is crystalline and particles are angular. Fortunately the major mineral constituents, sylvite (KCl) and halite (NaCl), demonstrate relatively low hardness at 2 to 2.5.Therefore, while simple abrasion must be acknowledged, it is not a major problem except, of course, in circuits carrying magnetite.Corrosion, as represented by the classic equations of Figure 2, occurs in all its various forms."

Jan 1, 1983

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By K. J. K. Weglo, M. U. Savich

"At the Falconbridge Limited, Canadian Nickel Division, Sudbury Operations, we investigated the ""NO NOISE"" ear muffs model NN3-F which is a Swedish product with foam-filled sealing rings (the Hellberg Standard Volume Hearing Protector). It is used extensively at Falconbridge mines in Sudbury.The research which was carried out in the four Falconbridge mines was conducted under three different headings: manufacturer's attenuation data (psychophysical method), clamping force and head size (bizygomatic diameter), and attenuation tests (physical methods) under working conditions.Manufacturers of hearing protectors claim their products offer noise reductions of 23 decibels (NRR) or more, but they fail to point out that this reduction is obtainable only under ideal conditions. The reality of attenuation under working conditions, as several studies have found, is quite different.Methods for using short measurements to determine the noise exposure index, and for controlling muff-wearing habits, were developed at the Elliot Lake Laboratory. Measurements taken at Falconbridge on ""NO NOISE"" ear muffs revealed that they have a practical attenuation of some IO to 13 decibels. It is important to note here that measurements also revealed that clamping force (thus attenuation) was in an inverse relationship with ear muff comfort. Measuring attenuation using noise dosimeters was a difficult job. Not a single surveyor would accept these measurements (physical method) for absolute accuracy. Apart from that, it was impossible to measure, in one shift, more than two work stations. Because of this, we sought a solution: measuring head size and clamping force in relation to actual attenuations.A detailed analysis of the relationship between attenuation and head size/clamping force was done at four mines. Standard deviation ellipses (standard error ellipses) for head size versus clamping force are in close agreement with measurements that were carried out. In order to measure clamping force an apparatus was constructed and a method for measuring suspension system durability is described in Appendices Band C of this report. At the same time we sought to reduce deterioration of ear muffs in mines as well as to put in place a system whereby attenuation can be controlled and improved. The clamping force apparatus can be operated automatically. The proposed control system is quick, simple and efficient . This system is equally applicable in small and large mining operations, and it can be totally automated and the data computerized for audit of the results. This control system is a new step in controlling ear muff attenuation in working environments.From these measurements of NN3-F ""NO NOISE"" muffs it can be concluded that ear muffs are not the total solution to protect the worker from noise.As the results were evaluated folio wing measurement, Falconbridge switched from the NN3-F ""NO NOISE"" muffs to approximately 90% Mark V ""NO NOISE"" muffs and 10% Mark V MSA muffs. These new muffs showed much better head size versus clamping force relationship and can be expected to produce 14 dBA or better attenuation of noise. RESUMEUne étude des casques antibruit ""NO NOISE"" modèle NN3-F, de fabrication suédoise, avec anneaux d'étanchéité en mousse (dispositif de protection contre le bruit ""Hellberg "" pour volume ordinaire)a été effectuée Ii la Falconbridge Ltd. , Division canadienne du nickel aux installations de Sudbury . Ces casques sont largement utilisés dans les mines de la Falconbridge Ii Sudbury.Cette étude aeu lieuen milieu de travail dans les quatre mines de la Falconbridge sous trois rubriques différentes soit: les données d'atténuation du bruit du fabricant (méthode psychophysique), la force de serrage et la taille de la tète (diamètre bizygomatique), et les essais d’atténuation de bruit (méthodes physiques). Les fabricants de dispositifs de protection contre le bruit prétendent que leurs produits offrent une réduction du bruit s'élevant Ii"

Jan 1, 1986

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited&apos;s Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company&apos;s Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

This paper presents the results of research aimed at proposing new solutions in the area of belt conveyor elements. Many factors, such as energy consumption costs, and operating costs of belt conveyor elements, including belts, idlers and drives have an impact on the operational costs of conveyors. The paper presents special tests of new materials for the bottom cover of an energy-saving belt conveyor, which decrease rolling resistance. It also presents large-scale in-situ tests of a high-output belt conveyor for the purpose of simultaneous measurements of various types of conveyor belts (standard vs several energysaving types) under typical operating conditions of a lignite surface mine. Improvements in materials used for the bottom belt covers, supported by specially developed comprehensive tests of the new types of belts have provided valuable results of various proposed solutions. Since the tests of belts were done at exactly the same time and in the same operating conditions, direct comparison of the results is valid and should lead to a substantial decrease in the conveyors? drives? energy consumption, which will improve the effectiveness of belt transport and minimize its negative influence on the environment.

Aug 1, 2013

By F. M. Doyle, G. Sidhu, A. J. Dussault, A. Raygani

There is a growing demand for rare earth metals for use in high strength permanent magnets, most notably Nd2Fe14B. Rare earth metals are extremely reactive, with reduction potentials around -2.5V SHE, and are conventionally produced by molten salt electrolysis. The current work was done to investigate an earlier report of electrodeposition of a neodymium ferroalloy from aqueous solution, to determine whether this approach could be an environmentally and economically competitive commercial approach for producing feedstock for permanent magnets. Such a process would be analogous thermodynamically to the Castner- Kellner process, in which aqueous sodium chloride brine is electrolyzed in cells with mercury cathodes. Metallic sodium forms an alloy (amalgam) at the cathode, thereby lowering the activity of the metallic sodium significantly below unity and making the reduction potential of sodium significantly less negative than the standard reduction potential. Here we report the effects of Nd/Fe ratio in the electrolyte, current density, temperature and two different complexing agents, glycine and cysteine, on the composition and morphology of the electrodeposits, along with current efficiency. The energy needed to produce neodymium as Nd:Fe alloys by aqueous electrodeposition was compared with values estimated for production by molten salt electrolysis and the thermodynamic energy requirement.

Jan 1, 2014

By George Efremidis, Markos Avlonitis, Elias C. Aifantis, Avraam Konstantinidis

"Nowadays, there is an increasing interest for realistic spring-block models capable of addressing precursor phenomena in catastrophic earthquake-induced landslides. By pre-defining the constitutive law between externally applied stress and induced local strain increments, the dynamic behaviour of the rock/soil slope can be studied by means of the distribution of slip events at the interface between the soil and the bedrock. It is shown that by relaxing the assumption of constant of externally applied stress rate and local strain increments, a robust 2D spring-block model can be formulated for studying triggered landslides. A cellular automaton is built in order to examine the dynamic behaviour and the stability of rock/soil slopes during the initiation of a landslide. The type and nature of the failure plane, as well as the triggering mechanism is studied. The different dynamic evolution modes of the slope can be mapped to specific shape parameters of the corresponding distributions of the incremental displacements. The proposed spring-block model can be used in order to understand, predict and minimize the impact of catastrophic landslides triggered by earthquakes.INTRODUCTIONEarthquakes have long been introduced as one of the major cause of landslides. Earthquake induced landslides are of great importance because they can cause considerable damage and life casualties. Existing analyses can provide landslide concentration, i.e. the number of landslide sources per square kilometer of surface area, as well as the distance from the earthquake source, which is related to the strength of shaking, the slope steepness, which is connected to shear stress, and finally the rock type, which is referred to material strength (Keefer, 1984). In spite of their great importance in social and economic life, earthquake-induced landslides are still considered as an open geotechnical problem. The dependence of the number and distribution of landslides on earthquake magnitude and ground shaking intensities is a crucial factor for the description and determination of the phenomenon. The hazardous types of earthquake-induced landslides, the most susceptible geologic materials and the reactivation of landslides originally triggered by nonseismic activity are some important topics for areas affected by landslides. Most of these areas present an irregular and asymmetric shape with respect to epicenters and fault ruptures, and also show a strong correlation with magnitude (Keefer, 1984, 2000). The number of landslides caused by an earthquake generally increases with increasing earthquake magnitude. Keefer (1984) presented a magnitude scale in order to quantify the number of earthquake-induced landslides. Malamud et al. (2004) have proposed an independent landslide-event magnitude scale on the earthquakes, based on the logarithm of the total landslides number associated with an event. The aforementioned studies try to relate the landslide magnitude scale to the visible effects of the triggering mechanisms."

Jan 1, 2015

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies&apos;, including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By T. Urbancic, Eric von Lunen, G. Viegas, A. Baig

"The characterization of the failure process of induced fractures by hydraulic stimulation is fundamental to understanding the generation and evolution of the discrete fracture network within the reservoir. A more detailed analysis of the fracture mechanism can be a powerful tool for identifying fluid flow paths and proppant placement within the reservoir. For example, during the rupture process the energy release is partitioned into different physical processes for which the relative ratio is changed by the presence of fluids or rotations in the local stress field with relation to the frictional resistance in the fracture plane. Fractures occurring in the same host rock under the same stress conditions are expected to rupture similarly, independent of their size (self-similarity). Changes in the scaling relationships of fractures are indicative of a change in the failure process, host rock or in-situ stress. Correlation of failure process data with reservoir rock properties and the in-situ stress field will help identify regions within the reservoir with characteristic types of failures. Further correlation with hydrocarbon production data can be used to develop efficient treatment plans and production diagnostic tools.In this study we investigate the failure process of ~27,000 microseismic (M < -1) fractures induced during a hydraulic fracturing shale completion program in NE British Columbia, Canada by estimating static and dynamic source parameters, such as dynamic and static stress drop, radiated energy, seismic efficiency, moment tensor, fracture plane orientation, slip direction and rupture velocity. On average, the microseismic events have low radiated energy, low dynamic stress and low seismic efficiency, consistent with the obtained slow rupture velocities. Events fail in overshoot mode (slip weakening failure model), with fluids lubricating faults and decreasing friction resistance. Events occurring in deeper formations tend to have faster rupture velocities and are more efficient in radiating energy. Variations in rupture velocity tend to correlate with variation in depth, fault azimuth and elapsed time, reflecting a dominance of the local stress field over other factors.Further identification of spatial and temporal distribution of families of events with similar characteristic rupture behaviors, based on either rock formation, depth, source type, fracture plane orientation, stress drop, pad or proppant stage, may be used as a proxy for specific fracture network development and hydrocarbon production. This information may be used to determine reservoir properties, constrain reservoir geo-mechanical models with measured physical parameters, classify dynamic rupture processes for fracture models and improve fracture treatment designs. These will be the focus of future studies."

Jan 1, 2015

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

By D. J. Archambeault, A. Saigal

Substantial cost savings have been demonstrated by material design changes after initial product development. As more information about a product&apos;s operating environment becomes available to a designer, it is possible to consider a more costeffective material that still meets or exceeds the design intent, such as minimum low cycle fatigue life. This is especially true in the aircraft engine industry, where precise operating cycle data is not available until after the first engine is built and tested. A methodology for predicting estimated low cycle fatigue life has been developed to investigate potential material change candidates for an aft cooling plate. A twodimensional macromechanical finite element model (FEM) has been developed using ANSYS and used to determine the effects of varying material properties. It is shown that slight changes in density, coefficient of thermal expansion and modulus of elasticity have profound effects on component and effective stresses, and therefore, estimated low cycle fatigue (ELCF) life. Aerospace

Jan 1, 2006