Search Documents

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By C. E. White

History The Con-Rycon mine is situated in the Yellowknife mining district, North West Territories, 608 air miles north of Edmonton, Alberta. The earliest reported discovery of gold in the area was made in 1898 but no extensive exploration occurred until 1928. The birth of Yellowknife as a mining community took place in 1934 with the staking of the Rich group and subsequent shipping of 16 tons of high grade ore. The Giant group was also among the claims staked in 1934, and later staking showed a tendency to close the gap between these two properties. In the fall of 1935, the A.Y.E. claims, situated south of the Giant group, were staked to cover a discovery of the Geological Survey of Canada and, after general release of the Survey's information, the adjoining ground was staked. These claims included the Con, Negus, Meg, and Kam groups. In 1936 four lapsed claims were re-staked as the P and G group and later acquired by Rycon Mines, Limited, controlled by the Consolidated Mining and Smelting Company of Canada, Limited. The Con and various adjacent groups owned by Cominco are now operated with the Rycon under one management. Surface trenching on the Con property started in 1936 and, during the fall and winter of 1936-37, a 60- foot 5 ft. by 9 ft. inclined prospect shaft was sunk. The encouragement provided by the shaft and diamond drilling in 1937 led to the decision to establish a mining plant, and in August, 1938, the 100-ton cyanide mill produced its first brick- the first gold brick poured in the history of the North West Territories. In November, 1938, the mill was enlarged to a 175-ton capacity and operated at this rate until 1941, when refractory ore was encountered. This situation was met by the installation of flotation and roasting units and, at the same time, the milling capacity was increased to 300 tons daily. Labour shortages and Government restrictions forced a reduction of output and in 1943 milling was suspended while mine development continued on a reduced scale throughout the war years. The present full-scale of operations was resumed in 1946 and the total production to the end of 1948 amounted to 288,853 oz. gold and 72,347 oz. silver.

Jan 1, 1949

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By Maurice Séguin

The primary aim of all ground geophysical work has been, of course, to locate orebodies. As with any geo-physical method, its success depends on a proper mastering of the types of surveys and equipment used and their application to the physical properties associated with the orebodies. The Schefferville deposits are iron ores subjected to enrichment by the process of leaching. Although some ore types are porous and low in demiity, most of the ore zones have had a net increase in density brought about by enrichment. In the course of their formation, the magnetic characteristics of the rocks have usually changed, as much of the magnetite was altered to relatively non-magnetic iron oxides and hydrous iron oxides. Ali drift-covered areas underlain with iron-formation are potential ore-producing areas. From these first two physical proper-ties and a determination of the thickness of the over-burden, a combined gravity-magnetic-seismic and/or resistivity survey allows for the detection and sorting out of iron-formation and potential ore zones from the country rocks. If the iron-formation possessed relatively uniform physical and chemical properties, the problem of locating areas underlain with ore, using geophysical methods, would be greatly simplified. Unfortunately, the iron-formation is a complex assemblage of rock types, each having different physical and chemical characteristics. In spite of this, qualitative and semi-quantitative correlation between the results of the surveys and the geology and structure of the area could be established. In addition, a semi-quantitative to quantitative correlation of the values of the residual gravity anomalies with the specific gravity, the iron content, the porosity factor, the dimensions of the under-lying orebodies and the values of the ground magnetic intensity above a reference lithologie unit, with the per cent weight Fe304 recovery and the susceptibility, led to the discovery of a direct-shipping iron ore deposit in the Schefferville mining district of Canada.

Jan 1, 1968

By G. F. Colborne, A. Thunaes

"When the Canadian uranium milling plants went into operation during the early 1950's, they utilized flowsheets developed at the Radioactivity Division of the Federal Mines Branch in Ottawa. Since then, numerous process improvements have been made by the Mines Branch, by the operating companies themselves and by other research organizations. This paper will consider uranium milling technology from the standpoint of a new mine operator charged with the responsibility for the design of an economic flowsheet, and will indicate the range of process elements available to him and the testwork required to enable an intelligent decision to be made."

Jan 1, 1968

By T. G. Carter

"Tremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems, with amongst the most advanced of the tools focusing on evaluating engineered openings within Synthetic Rock Masses. These new codes have the potential to allow much more realistic design, but they must not be used without careful calibration – prior to – during and – post completion of any modelling. This paper explores some of the pitfalls of inadequate data collection and suggests more emphasis be given to calibration. Guidelines for minimum levels of parameter data are suggested for improving application of basic to sophisticated modelling codes.INTRODUCTION & BACKGROUNDTremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems. The degree of sophistication now possible with some of the available codes allows one to tackle extremely complex problems that were not thought tractable even a decade ago. Indeed, generation of synthetic numerical rock masses, based on discrete fracture network representations that closely mimic actual rock mass conditions, such as are shown in Figure 1, is today relatively straightforward, and not as user-challenging as employing state-of-the-art codes of even a few decades ago. This is largely because major improvements in computer graphics and in availability of ready-made user-friendly input-output interfaces have paralleled development of these new codes, now in some cases outpacing actual new analytical/procedure developments. This is something of a reversal from the first few decades of DOS-based rock engineering computational experience, when only rudimentary graphics were available and user-friendly input-output interfaces were virtually non-existent."

Jan 1, 2015

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By Rejean Gagnon, Fernand Rochefort

"Haulage costs, in most operations, represent a large portion of total cost. Quebec Cartier Mining Company came to the conclusion t hat an electric trolley assist providing more horsepower than available from dieselgenerator sets presented the best oppor tunity for improvement. Accordingly, a testing and development program was carried out which resulted in the design, installat ion and application of a practical system. This paper describes the development of the system, the equipment used as well as the actual operation. A projection is also made to indicate further improvement in productivity. A comparison is made of truck operating data before and after activation of the trolley assist system in order to determine its economic impact."

Jan 1, 1972

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d'enterprises d'évaluer les réactions de la masse rocheuse aux méthodes d'extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l'exploitant pourra prendre les mesures qui s'imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d'extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l'appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d'utiliser les divers appareils."

Jan 1, 1987

By T. Feldmann, G. P. Demopoulos

The feasibility of chloride leaching processes depends on interfacing them with cost-effective HCl regeneration technologies. This paper summarizes the most important findings of research conducted in the past 3 years concerned with a novel process to regenerate high-strength HCl from concentrated CaCl2 solutions at temperatures below 100°C, via reaction of CaCl2 with H2SO4 resulting in the formation of calcium sulfate phases (gypsum, a-hemihydrate or anhydrite). From constant supersaturation semi-batch experiments in pure solution it was found that the crystal growth rate of hemihydrate, and hence the particle size, was influenced by the rate of reagent (Ca2+, SO4 2-) supply to the reactor. Additionally, growth studies of DH in presence of impurities (K+, Mg2+, Sr2+, Ba2+, Fe2+/3+, Al3+, La3+, Y3+, F- and PO4 3-) showed that specifically Sr2+ and PO4 3- are taken up during crystal growth. Furthermore, it was found that decreasing water activity (via different HCl/CaCl2 concentrations) and increasing temperature reduce the metastable life-time of DH and HH by increasing the phase transformation speed. The DH/HH transformation was identified to be dissolution-precipitation based, while HH to AH is a topochemical process. Finally, continuous experiments on bench scale are underway to confirm the feasibility of the process to obtain super-azeotropic strength HCl with up to 9 mol/L (~30wt.%) from 5 mol/L CaCl2 (~40wt.%) solution.

Jan 1, 2014

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By P. G. Rueffel

"Natural deposits of sodium sulphate are the result of normal geological processes. They are world-wide in occurrence and are found in depressions in arid and semi-arid regions. Primarily, the sodium sulphate deposits of the prairies are post-glacial and differ from rock salt deposits, which originated from connate water (fossil sea-water). Sodium sulphate on the Canadian prairies occurs as brine or in beds of intermittent and/or permanent crystals. Most beds are contaminated with various amounts of silt, sand and decayed organic matter. Soluble impurities such as chlorides, carbonates and bicarbonates of sodium and sulphates of magnesium and calcium are leached out from the soil of the surrounding run-off area of the deposits.In this paper, the origin of sodium sulphate, and the physical and chemical aspects related to the development of the Ingebrigt Lake deposit are dealt with. The problems of garnering raw material, and of refining and de-hydration are discussed, with emphasis on the Ingebrigt Lake plant. The utilization of the ""Total Power Concept"" in a sodium sulphate plant is described. The principal uses of sodium sulphate are also discussed."

Jan 1, 1968

By E. Lee Cameron

The old mine workings on four barite-fluorite veins of the Lake Ainslie district, Nova Scotia, were opened recently and channel sampled. The samples were then forwarded to the Ore Dressing Laboratories, Bureau of Mines, Ottawa, for chemical analyses. Following the analyses, the sample rejects were combined to form bulk samples, representing ore from each vein, for small-scale batch test work. Tonnage samples from the veins, for pilot mill testing, were submitted when requested by the Bureau. The results of the analyses on the channel samples showed that there are two grades of ore in the di strict, represented, for test purposes, by the Trout River vein and Johnson vein ores. Small-scale and pilot-plant test work was undertaken on both these ores. The Trout River ore is amenable co concentration but, because of the high-barite-co-fluorite-co-calcite ratio, a fluorite concentrate was not obtainable from the Johnson vein ore as received. However, Johnson ore blended in a 1 :1 ratio with Trout River ore gave a mill feed that was readily concentrated. The test work on these ores showed that the following concentrates are obtainable : (a) A barite concentrate, with a recovery of 85 to 95 per cent of the available barite, analysing 93 co 96 per cent BaS04, 4 co 6 per cent CaF,, and 0.5 co 2 per cent CaCO3. (b) A fluorite concentrate, with a recovery of 80 co 85 per cent of the available fluorite, analysing 94 to 97 per cent CaF, , 1 to 3 per cent BaSO., and 1 to 3 per cent CaCO3

Jan 1, 1945

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967