Search Documents

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By Percy Coulter

"GeneralThe Malartic Gold Fields mill is presently treating ore from four different companies. The ore is delivered by truck, by the shipper, and dumped into the Malartic Gold Fields ore bin. This ore varies in size from 'Run of mine' to minus 8 11, All ore is crushed to pass a 3/ 8 11 x 4 11 cross slotted screen.Weighing and SamplingAfter crushing the ore passes over an adequate-weigher (250 T .P.H. capacity) on its way to the fine ore bins. This weigher has a remote counter at the sampling point.A 36” Vezin sampler cuts 15% from the ore stream as it enters the mill bins. This portion is elevated, by means of a short belt conveyor, to feed the No. 2 Vezin sampler. (This elevation is necessary to give headroom for the following machines). The ore on the conveyor is levelled to give a uniform stream to the second sample cutter. The second, third and fourth cutters are 2411 •The No. 2 Vezin sampler cuts 19% from its feed and this portion falls directly into a 1611 x 1011 Denver rolls crusher. This crusher reduces the ore to -1/ 8 11 , approximately. The discharge from the rolls crusher falls on a revolving circular plate with scraper, which gives a uniform stream to the No. 3 Vezin sampler.The No. 3 Vezin cuts 10% from its feed. This portion falls on another revolving plate to give a uniform stream to feed No. 4 Vezin."

Jan 1, 1966

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By Larry M. Southwick

Extraction of gold and other metals from ores suspended in liquid slurries often involves gases (such as oxygen) as a participant in the reaction. An important factor then in setting the rate of extraction can be mass transfer of the gas into the liquid and/or solids. A number of recent studies have indicated that as solids loadings increase, mass transfer rates of gas into solid-liquid mixtures decreases. This would seem to imply that lower solids loadings would be beneficial to increased reaction rates. However, since it is the solids which are being reacted, a most intriguing paradox is created. More solids should lead to more surface area to react, but it seemingly also provides less gas to react. So is the reaction faster or slower as solids loadings increases? The creation of this paradox is imbedded in how mass transfer and reaction data is collected and measured, how it is analyzed and correlated, and finally on the rate controlling steps in the reaction. An alternative analysis of these studies is presented which clarifies and eliminates the paradox. The analysis applies to water slurries as used in gold or other metal leaching processes or in bio-hydrometallurgy, as well as to molten metal/solid/gas mixtures such as might be encountered in submerged gas injection.

Jan 1, 1999

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007

By Louise Grondin

Laronde Mine has been working for a number of years to identify substances that could contribute to process water toxicity and to find an effective way of removing these contaminants from the water. Initial studies have identified ammonia, nitrite, cyanide, thiocyanate, cyanate, dissolved organic carbon, copper and zinc as potential toxicants. Bench-scale tests were carried out with Lakefield Research to find a water treatment process that could effectively remove the suspected toxicants. Nine treatment processes were evaluated: 1) granular activated carbon (GAC) filtration followed by zeolite, 2) zeolite filtration followed by GAC filtration, 3) aeration followed by GAC filtration, 4) multi-stage GAC filtration, 5) chlorination followed by dechlorination, 6) addition of clay based polymer, 7) treatment with peroxide and ultra-violet light, 8) bulk addition of GAC and zeolite powder, 9) treatment with bacteria. This article presents a summary of the test results and of the problems associated with the evaluation of technologies for the treatment of toxicity.

Nov 1, 2002

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Paul Delottinville, Maynard Hall, Henry Hillier

"An expert system application for supervisory control and optimization of the indurating process at the Iron Ore Company of Canada (IOCC) has been developed and installed in closed-loop. Prior to the installation of the expert system, the indurating machine was rebuilt and the instrumentation revamped. A Foxboro I/A Distributed Control System (DCS) was installed for regulatory control, and a new control strategy configured. The modernization of the regulatory control has resulted in significant improvement in both production rate and product quality. Expert system control was implemented in September 1996. Preliminary indications are that the expert system has further improved the consistency of product quality, enhanced fuel efficiency and increased productivity. The expert system considers both wet and dry sections of the circuit, and its optimization scheme is driven by pellet tumble index and compression strength. Statistical Process Control (SPC) rules were implemented in the expert system as part of the quality analysis and control scheme. The expert system application was developed and delivered using the Comdale Expert Optimizer (CEO), and has been in continuous closed-loop control since its installation. The system development and implementation is described, and preliminary benefits are presented..... IntroductionIn early 1996 the Iron Ore Company of Canada (IOCC) contracted Comdale Technologies of Toronto to develop and implement a real-time expert system for optimizing the indurating pelletizing furnace at our plant location in Labrador City, Newfoundland.The decision to install the expert system has been timely. Like many other resource-based industries in increasingly competitive markets, IOCC recognizes the need to find ways to improve the efficiency of our production process and ensure that product quality is maintained at the highest levels. With the Labrador City plant producing 11 million tons of iron ore pellets annually, implementing the best technology solutions to meet these objectives is critical."

Jan 1, 1998

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By Funsho K. Ojebuoboh

With several “green” applications on the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulphide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter-blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure where by calcium and magnesium is used todebismuthise lead was developed. The present conduct of this 1936 process, the Kroll-Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1996

By M. Djivre, T. Eger, A. Godwin, I. Bhattacherya

Load-haul-dump vehicles (LHDs) are extensively used in underground mining, however, equipment design and operating conditions contribute to restricted operator sight lines. The inability to clearly see people, objects, or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, line-of-sight assessments are traditionally completed in the field. However, field methods are unable to evaluate lineof- sight under dynamic operating conditions, and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height. Results of this research show computer simulation and virtual reality can be successfully used to evaluate line-of-sight during the operation of LHD vehicles. In order to benefit from virtual reality applications, the work environment, LHD vehicle, and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic analysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHDs were developed from manufacturer specifications and pictures taken from LHDs currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle, and the vehicle and human were driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired line-of-sight were successfully identified with this method. The JACK program could also provide real-time feedback on the human’s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHDs evaluated in the JACK software package can also be combined with mine models and imported into other VR software packages (e.g. Blender) in order to enable viewing in Laurentian University’s Virtual Reality Laboratory. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial vision issues.

Jan 1, 2005

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By A. McLean, D. K. A Donyina, R. S. Segsworth

"Various aspects of processing ferro-manganese fines generated during the crushing of standard ferro-manganese have been studied in laboratory-scaleplasma furnaces. These laboratory furnaces are based on the use of conventional graphite electrodes rather than water-cooled non-consumable torch devices. The reactor system has separate, distinct zones for pre-healing, melting and smelting. This unique feature assists in the removal of undesirable elements from the molten alloy. Ferro-manganese alloys containing over 82% manganese, 0.004% sulphur, less than 0.01% silicon, 0.006% nitrogen, 0.001% oxygen and 0.0006% hydrogen have been produced from the offgrade ferro-manganese fines.IntroductionThe major application of manganese is as an alloying additive to numerous metals such as steel, aluminum, copper and magnesium. Manganese is mainly consumed in the ferrous industry in the form of ferro-manganese and silicon-manganese, or in its pure state as electrolytic manganese when certain impurities inherent in the manufacture of ferro-manganese and silicon-manganese alloys must be avoided. Before being sold on the market, ferro-manganese is crushed and during this process alloy fines are generated. Due to the nature of the casting process, the fines produced are contaminated with silica sand. In addition, due to segregation effect s, the pho sphorus content of the alloy fines is higher than that found in the bulk of the material produced. Because of the smaller particle size and the higher impurity content, there is only a limited market available for the alloy fines. For this reason, there has been increasing attention directed toward the development of processes for recycling fines through the conventional smelting furnaces. The fines may be charged to the furnace either directly or after agglomeration. The detrimental effects of charging the fines directly include:(1) decrease in gas permeability, causing irregular gas flow;(2) increase in the amount of dust produced;(3) packing and bridging; and(4) intensive reactions due to sudden flow in hot zones."

Jan 1, 1982