Search Documents

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today's prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By V. Murugaiyan

The Geotechnical Engineer is faced to view problems emerging from the task of protecting the environment and also the problems related to prevention of natural hazarders. Geo-Environmental Engineering, based on the development of geotechnical engineering, addresses the problems for the industrial world and the impact on health and welfare in relation to pollution of the ground. In the recent years, acute land pollution due to indiscriminate discharge of industrial effluents especially Organic acid based effluents has become one of the major concern due to erosion in the privatization of sustainable development under Indian Scenario. To study the effect of chemical changes on soil properties due to amino acid effluent contamination on soil and erosion behavoiur. The changes in the soil properties of effluent contaminated clay and silty soil were experimentally observed to be due to the interaction of organic and inorganic constituents of effluent on index properties of soil. The surface reactivity of soil mass is experimentally reported to be varying proportionately with respect to clay (%) in the soil. Also higher surface reactivity of clay increases the Solid Retension Time (SRT) with increase in rate of chemical transformation of organic and inorganic solids within soil. Hence soil S1 (high clay content 54.5%) showed increased SRT and soil S3 (low clay content, high silt and clay content 94.9%) showed decreased SRT and long transformation stage.

May 1, 2004

By C. L. O?Brian

Note: The figures quoted and used herein have been collected and furnished by the Dominion Bureau of Statistics. Without the help and willing co-operation of the officials of the Burreau, this study would not have been possible. Introductory and General Coal has one unique quality that distinguishes it from other minerals, one that is too, often forgotten. This is the quality of ubiquity. No other single mineral supplies such a wide and varied range of human requirements nor, up to the present, is there any indication of a rival in this regard. There is, consequently, reason for individual study of each of the major portions of the overall market for coa1. The provision of heat for our homes is a necessity of life in our Northern climate and the largest single source of this heat is coal. It is intended to present here a factual survey of the use ?of coal in home heating throughout Canada and the effect of these requirements upon the production of coal and the development of this phase of the mineral industry. The coals used for house heating in Canada fall into two more or less distinct classes, the very low volatile fuels such as anthracite and including coke, and the bituminous coals, including the sub-bituminous and lignite types. The bituminous coals are, of course, consumed in very large quantity by industry and the railways and are the most important type both in tonnage and in respect to the area supplied. Canada consumes annually for all purposes some 4,400,000 tons of anthracite, 4,300,000 tons of coke exclusive of Petroleum coke, and some 40,000,000 tons of bituminous coals. This is a fair measure of the relative importance to the overall economy although it will be seen later that the concentration of the household use of anthracite and coke into one area does create a considerable problem.

Jan 1, 1951

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company's San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By K. Awuah-Offei

Long-term production scheduling optimization has been a challenging issue for the mining industry because of the size and complexity of the problem. The current planning algorithms have limitations in terms of addressing the stochastic variables underlying the mine planning problem. In this paper, an intelligent agent-based mine planning framework based on reinforcement learning is introduced. The long-term mine planning is modelled as a dynamic decision network. The intelligent agent interacts with the block model by means of a stochastic simulation and employs a Q-learning algorithm to learn the sequence of pushbacks that maximizes the net present value of the mining operation. The intelligent open pit simulator (IOPS) was implemented with an object-oriented design in Java®. A comparative application case study was carried out to verify and validate the models. The proposed method was used in planning an iron ore deposit and the results were compared to the Milawa scheduler used in Whittle® software. The outcome of the study demonstrates that the intelligent agent framework provides a powerful basis for addressing real-size open pit mine planning problems.

Jan 1, 2008

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By G. R. Dunning, M. R. Wilson

"Abstract - The early Paleozoic accretionary tectonic regime that was established along the Laurentian margin of the Newfoundland Appalachians provided a favorable setting for shear-hosted gold mineralization along a major terrane suture, the Baie Verte-Brompton Line. The Stog’er Tight prospect is one of several mesothermal-style gold occurrences hosted by shear zones within accreted ophiolites and oceanic arc terranes on the Baie Verte Peninsula. It is an epigenetic, stratabound deposit that is confined to shallow-level gabbro sills within the volcanic cover sequence of the allochthonous Point Rousse ophiolite complex. Gold mineralization at Stog’er Tight is associated with hydrothermal mineral assemblages represented by chlorite-calcite, sericite-ankerite, red albitepyrite (±Au) and chlorite-magnetite alteration zones. Gold occurs with pyrite within the intensely altered gabbro, along the margins of syn- to late-shear, quartz-rich, replacement veins.The Stog’er Tight gabbro served as a rigid body conducive to shear deformation and fluid penetration, whereas, its high Fe-Ti oxide content induced fluid oxidation and gold-pyrite precipitation. Hydrothermal alteration involved progressive CO2, S, Na, and LILE metasomatism, along with significant enrichments in the REE, HFSE, and Th in the high-grade ore zone. Temperatures of vein formation and alteration are constrained by oxygen isotope thermometry to be between 250°C and 480°C. Isotopic compositions of vein quartz from the Stog’er Tight prospect are uniform (??O = +12.5 ± 1‰) and fall within the range cited for many shear-hosted, auriferous quartz veins.A U-Pb zircon igneous age of 483 +3/-2 Ma for the Stog’er Tight gabbro is consistent with its stratigraphic correlation with other Ordovician ophiolitic and volcanic arc/back-arc assemblages in Newfoundland. The U-Pb age of a rare variety of hydrothermal zircon recovered from the high-grade ore zone directly constrains the timing of gold mineralization to 420 ±5 Ma, in accord with a major orogenic episode of Silurian age that produced many of the magmatic and metamorphic rock suites in north-central Newfoundland. Our results are consistent with a post-peak metamorphic, late-magmatic model for gold mineralization that occurred during the waning stages of Silurian orogenesis, driven by emplacement of I-type granitoid intrusions into the crust."

Jan 1, 2000

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

By E. J. Debicki

"At the 1992 PDAC Convention, Norman Keevil announced the formation of the Exploration Technology Division (ETD) of the Mining Industry Technology Council of Canada (MITEC). It was evident that base metal reserves in Canada were declining and that the cost of discovering a deposit in Canada was increasing. Coordinated research to develop new exploration technologies was required to discover the next generation of ore-bodies. The ETD was formed in response.The mission of the ETD is to contribute to the survival, profit, and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral exploration through development of innovative technology by man-aging and coordinating applied cooperative research. In addition, it is the intent of the ETD to become the principal agency by which cooperative research funds are transferred to researchers from the mining industry. The division is industry driven, industry funded and industry managed.The ETD’s Three-Year Plan has focussed80% of its research funds toward two objectives, improving the efficiency of exploration for VMS deposits and establishing the parameters necessary to discover the next Hemlo deposit. The remaining 20% is allocated to other projects, with the current emphasis on geophysics.In 1995, corporate members total twenty-three major mining companies accounting for90% of the exploration expenditures in Canada. The ETD is currently managing ten cooperative research projects totalling $4.6million. Other projects, estimated at $1.6 mil-lion, are currently under development."

Jan 1, 1996

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By Tad Crowie, Victor Delgado, Nick Katsikaros, Tim Hughes

"A number of silver producers have identified a need for a system to recover silver and gold from base metal flotation concentrates on site rather than sending the concentrate to third party smelters to improve mine economics. Historically intensive cyanidation has only been used for coarse gold gravity concentrates in batch machines but Gekko have applied the InLine Leach Reactor (ILR) to these difficult to leach concentrates.The ILR’s unique ability to operate at various solid to solution ratios, high mass capacity, the ability to handle fines, the use of peroxide to aid silver leach kinetics and simple operation has resulted in significant economic benefits to Hochschild PLC’s Selene and Arcata operations. This paper describes the commissioning phase of the ILR5000BA intensive cyanidation reactors on concentrates from the Selene mine at the Ares Concentrator.INTRODUCTIONIntensive leaching of high grade concentrates in gold ore treatment is now commonplace and is considered an essential feature of most gold circuits (Lane, Fountain and LeBrooy, 2008). The devices commonly used for intensive leaching (InLine Leach Reactor, Acacia Reactor, etc) are specifically designed for the typical coarse nature of the concentrate.In some of these intensive leach applications, significant amounts of silver are co-recovered with the gold. In fact, the intensive leaching conditions of 1 to 2% NaCN in solution and high dissolved oxygen levels, overcome the issue with silver’s slow dissolution rate in traditional CIL/CIP circuits and avoids the formation of insoluble silver sulphide minerals on the surface of the gold (Marsden, 2006).There are a significant number of mine operators producing silver in the form of mixed base metal sulphides flotation concentrates. Typically the mine operators are paid for the silver after processing of the concentrate by the base metal smelter whom recovers the silver during the refining process."

Jan 1, 2010