Search Documents

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By D. M. Bastidas

The reduction of copper sulfide and copper oxides originated during artificial tarnishing of copper was studied using potentiodynamic potential/current density experiments. Six copper surface treatments were considered: mechanical polishing; indoor exposure for 7 days; chemical etching in 1.6 M nitric acid; chemical etching and heating at 160°C; and chemical etching and dipping in a 9x10-4 M or 0.9 M potassium sulfide (1(25) solution at 70°C. Cuprite (Cu20) and chalcocite (Cu2S) were the main compounds formed. A linear relationship with the square root of the scan rate (v) was obtained by plotting the potentiodynamic potential/current density for the tarnish dissolution processes. A relationship between potential and current density cathodic peaks was not obtained, according to Müller's model, showing a proportionality factor with the dimensions of a resistance.

Jan 1, 2007

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By James F. A. Hatley

Northern Saskatchewan comprises an area of about 350 000 km2 and boasts some of the world's largest known high-grade uranium deposits. The successful mining of these deposits, however, can not be accomplished without overcoming technical challenges. Not only is the high grade of the uranium ore challenging, but mining methods need to be developed to deal with groundwater at very high pressures, and ground conditions that vary substantially from excellent to wholly unconsolidated clays and sand. This paper discusses the various mechanisms of inflows at the three of the Cameco Corporation Mines in Northern Saskatchewan. The risk of inflows is quantified in terms of unique challenges from hydrogeologic conditions, rockmass integrity, and uncertainty in geologic conditions. Mitigation strategies in case of an inflow are also briefly described. The paper concludes by addressing the impact of institutional rules (corporate standards) on minimizing, monitoring, and controlling the probability and/or impact of unexpected inflows.

Aug 1, 2010

By Simon D. Handelsman, Malcolm Scoble, Marcello Veiga

"Abstract - In many mining areas, potentially profitable mineral projects can be at risk because local people do not trust their governments and mining companies on many issues, including human rights. Projects will continue to be vulnerable to potential failure, delays, and higher costs. This paper suggests that geoscientists need to be aware of the global challenges they face from issues of corporate social responsibility, sustainable development, and human rights. These are not areas in which geoscience education has traditionally focused.This paper examines the types of conflict concerning human rights that are encountered by geoscientists involved in mineral exploration and development. It provides a background to human rights issues and presents a classification of the types of issue encountered. It reports on a survey of case studies that provide examples of the breadth, complexities, and consequences of such issues. The paper then concludes by outlining the development of codes and standards to improve performance, and suggests approaches for positive, practical engagement."

Jan 1, 2003

By R. S. Rogers

Abstract - Forensic geology in a mineral exploration context is concerned with geology and related technical matters as they pertain to legal cases involving exploration and evaluation of mineral properties. Such cases involve the possibility of outright scams that include falsification of data and information, as well as inappropriate application of various technical procedures. Experience in forensic geology in such cases emphasizes the need for systematic quality control procedures during routine exploration/appraisal and indicates the need for more attention to ‘target hardening’ (improving security in the chain of custody of samples and assay results). A number of ‘early warning signs’ that might suggest some form of tampering or falsification of information are listed. These measures will support the work of the "Qualified Persons" (geologists and engineers) entrusted with the scientific and technical aspects of mineral exploration, and facilitate the increased attention to regulatory oversight and enforcement of securities laws recommended in the report "Setting New Standards."

Jan 1, 1998

By R. Abel

During the last eight years, the Ventanas electrolytic refinery has been improving its results by applying a series of new operational practices, such as the reduction of electrode spacing from 115 mm to 105 mm., raising the current density to 305 A/m2, modification in the operators shifts to about 70% of the workers, reducing the pulling cycles by two hours, and the erection of a new anode preparation machine. These improvements allowed an increase in the refinery capacity from 323,000 to 382,000 metric tons of electrolytic copper per year. In the same period it has obtained certification under the ISO 9001:2000 and ISO 14001:2004 standards. All of these developments have been achieved using conventional technology with copper starting sheets. The continuous improvement that is covered in this paper has allowed Ventanas to optimize its production, costs, and operational results. For the next years, it is planned to follow the same tendency, bringing the productivity of the plant to higher levels.

Jan 1, 2007

By I Wilkomirsky, F. Parada, R. Parra, E. Balladares

"The neutral roasting of As bearing copper concentrates is confirmed well established and promising option for the treatment of this type of complex concentrate. The AS elimination by volatilization allows subsequent treatment of the calcines produced in a conventional pyrometallurgical process, by blending this product with standard concentrates.Several tests were performed using the fluidized bed pilot plant at the University of Concepción with different types of concentrates. Calcines, fines from two hot cyclones and flue dust from the ESP were collected. These materials were characterized using QEMSCAN® and the results used for the development of a mass and energy balance which took into consideration the specific chemical transformations that occurred in the reactor.A physico-chemical/kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite. The mechanism involves solid-gas reactions between chalcocite, pyrrhotite and gaseous sulfur that without the mineralogical characterization would not have been possible to propose"

Jan 1, 2014

By Gary Raymond

The Similkameen Division of Newmont Mines Limited operates a low-grade open-pit copper mine in southern British Columbia. The copper mineralization is extremely erratic.As a result, over seven years of operation, ore control methods have evolved from standard flagging based on blast-hole assays, through an in-pit grab sampling system, to the present method of mining to computer-determined ore-waste boundaries based on geostatistics. These improved ore control methods have resulted in a gain of at least 25% on ore tonnage miffed, at the same grade as obtained using earlier techniques. At the same time, geostatistical ore reserve estimates are now within 7% of milled ore tonnage and grade on a yearly basis, whereas the original polygon ore reserves under-estimated mineable ore tonnage by 15% to 45% and over-estimated grade by about 20%. The author discusses why traditional ore estimation methods give poor results in erratically mineralized orebodies and describes the geostatistical approach to the problem.

Jan 1, 1979

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By V. I. Birss

Planar solid oxide fuel cells (SOFCs) offer great promise as stationary power generation devices, primarily due to their flexibility in terms of fuels, high energy conversion efficiency (when both electricity and heat are captured), and their relatively low fabrication costs. However, the anode performance can be compromised by such factors as exposure to certain sulfur-containing fuels and the deposition of coke when using hydrocarbon fuels. In terms of the cathode, its performance is limited primarily by the slow kinetics of the oxygen reduction reaction, while its lifetime can be negatively affected by factors related to the corrosion of currently used stainless steel interconnect materials. This talk will present an overview of these challenges and some possible solutions to these problems. The presentation will also focus on how electrochemical methods can be used to evaluate and improve the performance of SOFC anodes, cathodes, and interconnect materials. In addition, recent promising research efforts directed towards performance enhancement of SOFCs through the use of nanoscale electrocatalysts will be discussed.

Jan 1, 2005

By Y. -B. Kang

New databases are being developed to provide the capability to evaluate the suitability of present and potential new Mg alloys for automotive applications through cost-effective calculations. An extensive and complete thermodynamic database is being prepared for Mg alloys formed from among 25 present and potential alloying elements. The database is being developed by critical evaluation, modeling and optimization of available phase equilibrium and thermodynamic data. It contains model parameters giving the thermodynamic properties as functions of temperature and composition. Using the FactSage thermodynamic software, users can access the database to calculate the amounts and compositions of all phases at equilibrium at any temperature and composition or to calculate any phase diagram section in multicomponent alloys, to follow the course of equilibrium or non-equilibrium cooling, to calculate corresponding heat effects, etc. A database of densities and lattice parameters of Mg alloys and intermetallics (as functions of temperature and composition) is also being developed in order to permit the calculation of volume changes during cooling and phase transformations, c/a ratios of the hcp phase, etc.

Jan 1, 2006

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By B. F. Giyani, D. Rahal

"Stirred media mills have proved to be more energy-efficient than the conventional ball milling for fine grinding applications. The mill performance is governed by a number of operating variables including mill stirrer speed, feed particle size, solids content and slurry rheology. A study was conducted to assess effects of mill speed, media size and density, and slurry density on the Stress Intensity (SI) in a VXPmill and thereby the relationship to mill performance. For the mill speeds tested, it was found that the optimum tip speed is 7 m/s. If the speed is too high (12 m/s) energy losses result due to mechanical friction losses and heat generation. If the speed is too low (3 m/s), the kinetic energy is not sufficient to promote breakage. The size reduction ratio increases with the increase in mill speed and the decrease in solids content especially in the coarse fraction particle sizes. The effect of slurry rheology on mill performance was shown by assessing the effects of increasing solids concentration and decreasing particle size. Rheological effects seemed to interact with mill speed such that the mill was less energy-efficient at higher solids content and at higher mill speeds particularly for grinding to fine particle sizes. There is an opti"

Jan 1, 2017

By I. Raheb, M. Y. Debili

"A set of Al-Co binary alloys (with respectively in weight percent 10%, 20%, 30%, 40%, 50% and 60% Co) have been studied by X-ray diffraction at the as compacted state. The structural evolution according to cobalt addition shows special features as the apparition of fcc cobalt and hcp cobalt beside aluminium in some cobalt compositions of the Al-Co mixtures using only cold compaction without sintering at high temperature. Figure 1 Cobalt is not a common alloying element in aluminium because its solubility is very low [1]. According to the pressure-temperature phase diagram, Co is known to exist in two allotropic forms: a low-temperature hcp phase and a high-temperature fcc phase [2-3]. At room temperature, Co is stable in the hcp form but it transforms to the fcc form when it is heated to above the transition temperature 695K. Powder aluminium and cobalt (99.999 %) were used in the proportions defined according to the required compositions. The total mass of the samples to be elaborated was between 8 g and 10 g. Cold compaction of mixed powder (Al-Co) under an uniaxial load of 10 MPa has been achieved to obtain a dense product (60%)."

Jan 1, 2015

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

"Nanisivik Mines Ltd. operates a 10-M W diesel-electric generating plant at its zinc-lead operation on Baffin Island in the Canadian Arctic. This paper provides a description of the plant and the integrated waste heat recovery system. Data is presented detailing the actual costs of operating a plant over a period of seven years. Problems in operation are described as well as the success of the plant in meeting its objectives over the years. IntroductionNanisivik is located on the shore of Strathcona Sound at the north end of Baffin Island (Fig. I). Nanisivik Mines Ltd. has operated a 2,100 tonne per day zinc-lead underground mine and a concentrator, together with supporting infrastructure, at this location since October 1976. Annual production of 100 000 tonnes of zinc and 10 000 tonnes of lead concentrate is transported by ship to Europe during the mid -July to mid October shipping season.All electrical needs of the project are provided by the company-owned and -operated power plant. Facilities served by this electrical system are the underground mining areas, the concentrator and industrial area, a townsite, airport, and shiploading dock complex."

Jan 1, 1986

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019