Search Documents

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By G. Lucas

"Material substitution occurs continuously in response to competitive and economic pressures. Technical development can accelerate or slow substitution by improving the performance of the invading or defending material. The choices are seldom simple and have to be made in the context of continuous commercial change.The development and commercialization of a new aluminum material is examined. The material has been introduced into· several different markets, so it is possible to compare and contrast the degree of success obtained in each.IntroductionAluminum-based materials have been in use for over one hundred years and , therefore, the development of a new family of alloys is rare. In the early 1970s, Dr. L.R. Morris and his coworkers at Alcan' s Kingston Research Centre started work on what was, at the time, something of a scientific curiosity-a family of alloys strengthened by an unusual mechanism.This paper deals with the development and commercialization of what became known as the Alcan 255 alloys"". These alloys have found uses in several markets, usually as improved substitutes for existing materials. Forecasting the usefulness of a substitute material in an existing marketplace is difficult, in part, because even material users are seldom able to specify precisely their requirements. This uncertainty can cause the failure of some substitutions but can also lead to opportunities which were not initially obvious.Technical BackgroundPure aluminum is a soft, weak material. It can be strengthened by the addition of various alloying elements and by work hardening. Alloying elements usually act by forming solid solutions which are stronger than the pure metal or by precipitating during heat treating or aging and so preventing the easy movement of dislocations during deformation. Elements which can perform either role had been investigated for decades and were thought to offer little chance of technical breakthrough in 1970. An outgrowth of the then new and exciting research on directional solidification seemed, however, to offer such promise.Some aluminum-iran-manganese alloys will solidify under certain conditions as 'coupled growth' eutectics (Figs. I and 2). The microstructure shows one phase growing as long rods through the other. This is an uncommon structure and it was investigated to see if it had equally unusual properties. On deformation by rolling the rods were broken up into small equiaxed , evenly-spaced particles (Fig. 3). Materials with this structure were found to be stronger than other alloys with similar amounts of alloying addition, and to resist thermal softening remarkably well. This combination of properties was thought initially to be due directly to the particles by a dispersion strengthening mechanism, but later this was found not to be strictly true."

Jan 1, 1987

By Barry James

"This paper discusses past and current energy use patterns in the mining and manufacturing sectors of the industrial minerals industry. Information is presented on the primary energy input types as purchased by the industry, the quality and form of the energy actually required by the various production processes, and the residual form of this energy, either embodied in the product or rejected in gaseous and liquid waste heat streams. With the continuing concerns about the availability of energy combined with the rapidly increasing cost of energy as a production input, the reduction of energy usage through improved efficiency will undoubtedly be an increasing priority for the industry during the 1980s. Reduced energy consumption through investment to improve energy efficiency appears to be advantageous from both the corporate and national perspectives.IntroductionEnergy, like labour and materials, is one of the basic production input s to the various mining, processing and manufacturing production stages in the industrial minerals industry. Energy costs, as a percentage of total production costs, have been well above the average for industry in Canada, accounting for more than 50 cents out of every dollar in the most extreme cases. Consequently, energy has always been a relatively important management concern in the industrial minerals industry.The energy supply and price situation in Canada and internationally has been changing rapidly since 1973, following a long period characterized by declining real energy prices and an abundance and wide choice of energy supplies. It is generally accepted that energy prices will continue to increase rapidly, and that there will be uncertainties about the long-term continuity of supply of some energy types. In essence, a period of relative stability has been replaced by a period of relative uncertainty. In such a changing situation, a reassessment of the role of energy as a production input is appropriate.The following sections outline some of the effects of the changing energy scene on the industrial minerals industry. These effects are dealt with primarily in terms of energy costs, because, in most circumstances, a change in the cost of energy as a production input is the end result of both energy price and energy supply changes."

Jan 1, 1981

By Michel Dostie

Un séchoir à vis chauffé par induction électromagnétique a été développé et implanté chez Mines Niobec pour le séchage d?un concentré de niobium. Ce séchoir a permis une réduction des émissions de poussières et des gaz à effet de serre de l?usine. Il offre une grande souplesse de contrôle, une meilleure efficacité énergétique et peut être utilisé pour le séchage de granulats, de poudres ou autres substances habituellement traitées dans un four rotatif ou à l?aide de vis chauffées par un caloporteur. Le principe de fonctionnement du séchoir est simple. Trois inducteurs opérant à la fréquence du réseau électrique assurent le chauffage des parties métalliques du séchoir, dont des vis qui servent à convoyer le matériel. Le contact du matériel avec les parties métalliques chaudes permet le transfert de l?énergie requise pour le séchage. La conception de ce type de séchoir requiert un équilibre adéquat entre les besoins associés au chauffage par induction et ceux liés au transfert de chaleur par contact et au transport du matériel dans le séchoir. Cette première implantation industrielle a nécessité des efforts de développements importants et une collaboration des différents intervenants. Une revue des principes de conception, des difficultés rencontrées et des performances obtenues sera présentée.

May 1, 2007

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By C. J. Newman, K. Molnar, A. G. Storey, G. Macfarlane

"The Kidd Creek copper smelter started operation in June 1981 using the Mitsubishi Continuous Smelting Process. A steady increase in plant production rates has been demonstrated, and the annual tonnage of concentrate smelted is now double the original design rate. This paper summarizes recent modifications made to increase concentrate feed rates, increase on-line time, reduce copper losses and control the impurity level in anode copper. It includes improvements made to furnace design, improvements to reduce downtime f or boiler cleaning, and improvements made to the acid plant to allow handling of increased gas flowrates and higher gas strengths while maintaining low acid plant emission rates. IntroductionThe Kidd Creek Division of Fal conbridge Limited operates a base-metal mining and metallurgical complex, located in Timmins, Ontario, which includes an underground mine, a 13 500 tonne/day concentrator, a 130000 tonne/year zinc plant and a copper smelter and refinery, The copper smelter and refinery were commissioned in 1981, with an installed capacity of 59 000 tonnes/ year of cathode. The smelter, utilizing the continuous smelting technology of the Mitsubishi Process, has subsequently been expanded in production capacity, and in 1991 produced 113 500 tonnes of blister copper The capacity of the refinery, which uses Onahama No. 3 tankhouse technology, has been increased to 96 000 tonnes/year of cathode. The capacity increase at the smelter has been realized through the input of additional oxygen to both the smelting and converting furnaces, without increasing the process off-gas flowrate through the associated waste heat boilers.In this paper, a brief review of smelter operation and modifications in the period 1982 to 1987 is presented, together with a more detailed discussion of operation during 1988 to 1991, and a discussion of future planned improvements."

Jan 1, 1992

By M. Nagamori, A. J. Plumpton

"A low-grade concentrate from the Crevier Township, Quebec, containing 1.8% Ta205 and 13.7% Nb205 was reduced with carbon at 1600°C, and niobium and tantalum were selectively absorbed in liquid iron. To slag off the zirconia-rich gangue, some silica and lime were added as flux. Metallic iron was added in such a way that the combined contents of TaC and NbC did not exceed 20% in the ferroalloy . Up to 95% of the niobium, and up to 80% of the tantalum contained in the concentrate were recovered in the metal. The ferroalloy was ground finely and dissolved in 2 wt % sulphuric acid to leach out iron and silicon preferentially. The insoluble residue consisted principally of NbC and TaC, the calcination of which yielded an enriched concentrate comprising 80% Nb2O5 and 8% Ta2O5. The insoluble residue could also be chlorinated to obtain an impure liquid of Nb2Cl5 and TaCl5. Process variables and their effects are discussed in terms of higher metal recoveries in the smelting.IntroductionPresently, about one-third of the world production of tantalum comes from the pyrometallurgical reprocessing of tin slag, a by-product of tin smelting, containing sometimes 2 to 10% Ta205 and about the same amount of Nb205. Upon heating tin slags with carbon at about 1600°C in an electric furnace, tantalum and niobium oxides are converted to TaC and NbC, which are absorbed by the coexisting phase of molten metallic iron(1,2). The Fe-Nb-Ta-C melts cannot be decarburized by oxidation because of the preferential formation of Nb and Ta oxides over CO gas(3). So, the ferroalloys containing tantalum and niobium carbides are commercially treated by acid-leaching and I or chlorination to eliminate iron and thus permitting the eventual recovery of purified tantalum and niobium oxides(2).Absorbing Ta and Nb carbides in molten iron was first proposed and demonstrated by Zimmerley and Back(4) in 1957 in order to recover selectively tantalum and niobium from lowgrade concentrates. The process was successfully applied to the electric furnace smelting of tin slags by Hunter and Fursmant(5) over a period preceding 1965."

Jan 1, 1985

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

"Cambior now holds a 49% interest in the Valdez Creek Placer, having acquired American Barrick's 23.125% interest in May 1990. At the same time, the company assumed the management of the operation and received environmental permits to divert the river. Plans are underway to divert the Valdez River in order to continue mining the deposit upstream, and to construct a new, higher capacity wash plant (by 60%) closer to the operations. Mining operations, which were suspended in October 1989 pending higher gold prices, resumed in August 1990. The mine is expected to produce 10000 ounces of gold in 1990and more than 80 000 ounces in 1991.IntroductionThe Valdez Creek Placer is located in the Valdez Creek mining district of Alaska on the western flank of the Clearwater mountain range, about 150 miles northeast of Anchorage by air (Fig. I) . The mine is accessible by air or by road.The mine is situated at an elevation of about 3000 ft and is isolated from towns and villages. Consequently, the mine site contains the facilities necessary to house and feed 135 people at any given time. The Valdez Creek Placer has 159 employees, including 130hourly and 29 salaried employees. The hourly employees are divided into three rotating teams. The daily schedule consists of two shifts of 12 hours, and each team works 14 days followed by seven days off, resulting in a weekly rotation of teams.The salaried employees work normal hours for ten consecutive days followed by four days off. A weekly rotation ensures continuity of services and management.Gold was first discovered at Valdez Creek in 1903, when a team of four men led by Peter Monahan left the village of Valdez to explore the area up the Susitna River, to the east of Mount McKinley. They discovered gold at the mouth of a creek that they immediately named Valdez Creek, in honour of their native town. In 1904, they discovered the Tammany Channel to the right of Valdez Creek. This was the beginning of a long period of mining in the area which continued until the beginning of World War II .In 1980, the Denali Mining Co. was formed. Geophysical work and drilling carried out through 1980 and 1981 led to the discovery of Channel A, a second channel which is older than the Tammany Channel. In 1983, Denali Mining optioned its claims to Camindex to explore, develop and mine the Valdez Creek property. A joint venture agreement was signed among Camindex, Talcorp, BCP Alaska (Barrick), Sum Resources (Cambior), Norfran and WGM to form Valdez Creek Mining Co., Inc., and production began in 1984. Valdez Creek Mining Co., Inc. (VCMC) was subsequently restructured and in 1989 was held by the following three companies: Camindex Mines Ltd. - 51070; Cambior Inc. - 25.875%; and American Barrick - 23.125%.VCMC is managed by a committee of the partners. Decisions made by the committee are subject to a 70% majority vote. Cambior receives its share of production in kind, and contributes in the same proportion to the expenses of the joint venture (VCMC)."

Jan 1, 1990

The Project ? $1.4 billion project ? 59,000 tonnes of nickel and cobalt ? Large resource base ? First production end of 2004 The Place ? Half the size of Vancouver Island ? Population 210,000 ? 43% Melanesian, 37% European, 12% other South Pacific groups, 8% other nationalities ? Tourism principal industry ? 1/3 of world?s nickel resources The Politics ? French Overseas Territory ?1998 Noumea Accord: increased local control over domestic policy ? Referendum on independence in 2014 ? Seeking more economic autonomy, less dependence on French support

May 1, 2002

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

By Fathi Habashi, Michel Pagé, Farouk T. Awadalla

"Chrysotile asbestos can be dyed with certain dyestuffs to form stable coloured products whose hemolytic and cytotoxicity are greatly reduced. Examples of these dyes are Thiazol Yellow G (a monazo dye) and Trypan Blue (a diazo dye). Other dye stuffs, for example, basic dyes with triphenyl methane structure, Brilliant Yellow (a diazo dye), and Methylene Blue (a thiazine dye) colour asbestos but do not reduce its toxicity. Similarly alizarin, 8-hydroxyquinoline, and representative members of the phthalein group Bromocresol Purple and Phenolphthalein.IntroductionThere is, at present, a controversy regarding the dangers of asbestos fibres, and attempts are being made to render it less toxic. One of these attempts consisted of treating chrysotile asbestos with gaseous phosphorus oxychloride, POCI], at ambient temperature and in absence of moisture. The product had to be heated at 300°C to 500°C to expel exess entrained reagent to get a material containing 0.5070 to 5% phosphate groups and known as Chrysophosphate (Lalancette and Dunnigan, 1982). This product showed decreased toxicity as measured by its hemolytic effect on red blood cells (fable 1). In another approach, Flowers (1983) showed that when chrysotile asbestos was thoroughly mixed with a solution of ferric ammonium sulphate and the slurry was then filtered and dried, the product showed a marked decrease in cytotoxicity.In the present investigation the problem of toxicity was considered from a different point-of-view. Chrysotile asbestos is a hydrated magnesium silicate that can be represented by the structural model shown in Figure 1 from which it can be seen that magnesium hydroxide groups, Mg(OH)2, form a part of the silicate structure. Certain organic reagents that are known to react with magnesium ion in solution to form chelates were reacted with asbestos to find out whether a chelate was also formed on the fibres, and if so , what will be the hemolytic action and cytotoxicity of the product."

Jan 1, 1991

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By Karl J. C. Harries

"9.1. INTRODUCTIONIn Chapter 5 of Volume I royalties are dealt with and several topics would appear to be duplicated in this Volume. However, Volume I may be looked upon as a general guide, whereas this Volume is a reference volume. It deals in considerable detail with specific provisions and concepts relating to royalties between private parties. This does not, however, mean that Chapter 5 can be ignored. It should be looked upon as a source of general information concerning royalties between private parties and as a negotiating aid intended to give an overview of various topics. You may well find that in its general approach it will lead you to ask a question which, hopefully, will be dealt with in this Volume .It should be remembered that royalty agreements are agreements with a particular focus, and so the concepts set forth in Chapter 1 apply to them. This chapter addresses a few considerations specific to royalties that will usually form part of an agreement rather than a stand-alone agreement.9.2. FORMAT FOR ROYALTY PROVISIONSIn many of the cases where royalties arise, they are adjunct to, or part of, other arrangements. For example, a royalty may form part or all of the consideration to be given to an owner upon purchase of his property, or it may arise if a joint venturer ceases to contribute to the venture and has his interest converted to a royalty.1 It is with such situations that this section primarily deals; if the royalty is contained in an agreement that is singularly, or primarily, concerned with creating it, then it is just a normal agreement.Commonly, by the time the right to receive the royalty arises, at least some of the other provisions of the agreement have been performed and/or become redundant. For example, in an option agreement the royalty will be a continuing obligation of the optionee, usually arising only after the option has been exercised.2 In a joint venture agreement, a royalty will often arise where the interest of a non-participating venturer has been diluted and converted to a royalty, in which case the recipient will usually become a passive party, entitled only to his royalty, and most of the rights that he enjoyed as an active venturer will cease to be effective."

Jan 1, 2003

By Longjiang Li, Song Mao, Zhengyang Qiao, Qin Zhang, Guizhou University, Ling Wang

"After a study on the advantages and disadvantages of flotation column, according to the limitation of ordinary flotation column only is used for a flotation of microgranular minerals, the paper designed a new kind of layered convection coarse particle flotation column.Using a bauxite to test the rationality of the flotation column.The test results show that the new layered convection coarse particle flotation column is feasible.It has certain advantages about coarse particles flotation.INTRODUCTIONFlotation column has many advantages, for example,a simple structure, high efficiency and energy saving, the obvious advantage of fine particles flotation , the index superior and so on. The advantages gradually getting people's recognition. Research of flotation column has been a breakthrough, however, due to it only is used for the flotation of microgranular minerals, and the microgranular mineral particles will lead to a series of problems, and makes the processing cost is increased. Due to increase grinding fineness can save the grinding time and reduce the cost of grinding, also can avoid the disadvantage of fairly granular mineral particles cause a deterioration in the flotation. So it is necessary to research a kind of coarse particle flotation column.After a research on the advantages and disadvantages of flotation column, the authors designed and manufactured a new layered convection coarse particle flotation column, the flotation column both in theory and operation is better than flotation machine.DESIGN OF THE LAYERED CONVECTION COARSE PARTICLE FLOTATION COLUMNAdvantages and Disadvantages of the Traditional Flotation ColumnIn the field of mineral processing, as the increasing proportion of ore that has low grade, fine dissemination size, complex mineral composition characteristics. The limitations of traditional flotation machine is increasing[1],for instance, the high energy consumption, severe wear, inconvenient configuration , large amount of maintenance and so on. Compared with flotation machine, the flotation column with high separation efficiency, low investment and production cost, covers a less area low installation cost, less reagent dosage, more suitable for separation of fine particles and can automatically control, etc[2]. At present, the ore is facing the world energy crisis situation, and becoming increasingly difficult to flotation. So it is important to invent a coarse particle flotation column."

Jan 1, 2016