Search Documents

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author's experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By J. M. Turnbull

THE primary objective of the young graduate, after the war, will be to obtain a suitable position within the Industry, with adequate pay and opportunity to advance. The positions available to meet this demand will depend on the magnitude and organization of the industry. The size of the mining industry, in particular, will depend on a number of factors, including depletion; new discoveries of mineral deposits; beneficiation of new kinds of mineral deposits, based on research; technical improvements, also based on research, enabling the mining of lower grade deposits; and complex social factors. The organization of the industry will depend on its control and management, which may be greatly affected by social conditions and changes, and may include a wider or a narrower use of technical services. The corresponding training or qualifications of graduates, to meet these conditions, calls for a consideration of educational requirements and facilities in relation to the conditions that are likely to occur. Some forecast of the probable future of the Industry, after the war, based on consideration of. the above factors, is necessary as a basis of discussion, since the graduate must find his place in the industry of that time, and find his work in maintaining and improving it, within the existent social framework. Social factors are pressing and? important at present and their future impact is uncertain. In considering these, a few quotations and extracts may be in order. "A new economic order, based on free access to the sources of raw materials, means free use of the world's wealth by all civilized nations" (The Pope. Also advocated by Churchill and Roosevelt in the Atlantic Charter). "Every citizen should have a voice in the conduct of business or industry which is ?carried on by means of his labour" (Archbishop of Canterbury).

Jan 1, 1943

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By H. T. Fargey

This paper considers the social, economic and political factors and their influence on future production and marketing of Western Canadian minerals. Among the subjects discussed are inflation, taxation, anti-combines legislation, unstable international currency relationships, economic nationalism and protectionism, the European Common Market and environmentalism.

Jan 1, 1973

By Bradley Stoughton

It is very easy to reduce iron ore at a temperature well below its melting point and produce a more-or-less-pure metal which can be used directly for implements, tools, or machines. This simplicity has been the cause of much money loss by persons who were so satisfied with the successful operation of a process that they paid all too little attention to the commercial aspects of it. How easy a direct process is may be gleaned from the fact that it was practised with some -success by primitive man, and has been in almost continuous operation in one form or another for a period of probably 4,000 years. The production of steel in ton lots, beginning about 1860, brought a new phase into the economic situation, which, however, had been already greatly modified in 1784 by Henry Cort's invention of purifying pig iron. Direct processes survived both of these revolutions, under special geographical conditions, even up to the last few years of the nineteenth century, but ceased to have any general use as the basis of supply for structural, machine, or tool industries even in countries which could have manufactured iron by a direct process, but, instead, imported the product of established iron and steel processes. And this is still the situation today, notwithstanding the invention of an incredible number of 'new' processes since 1900, most of which are abandoned, and only survived as along as their financial backers were willing and able to Jose money. Probably none of these processes failed to work pretty well, and all seemed to show a handsome profit on paper.

Jan 1, 1930

By P .. H. Grimley, N. Champigny

"Fourteen companies (Appendix) representing senior mining organizations in Canada were canvassed in order to assess: (1) the current usage and trends, and (2) the usefulness of computer applications in ore reserve estimation and grade control. The results of the questionnaire suggest that:• computers are unsurprisingly, predominant in the mining industry for calculating reserves and performing grade control;• time and cost savings are realized;• computer-based approaches are applicable to underground situations;• geological information is incorporated to the computerization process; and• computer usage does not hinder the collaboration of geologist and mining engineer.A clear need is identified for case histories comparing computer-calculated ore reserves and actual production data.IntroductionAmong the management and technical staff of some mining companies there is a perception that the application of computer based technology for the estimation of ore reserves and grade control, has as many drawbacks as benefits. Some of the objections raised against the utilization of computers for ore reserve estimation are that:• computer-based reserve models work for large open pit mines but not for underground situations;• computer-generated reserves ignore the geologist's knowledge base; they are strictly a number crunching exercise; and• the use of computers for ore reserves hinders collaboration between the geologist and mining engineer.In order to determine (I) the extent of current computer usage and future trends and (2) whether the objections noted above are borne out by experience, a number of senior Canadian mining companies were canvassed.The respondents were asked to provide:• an assessment of the importance of the computer in the ore reserve estimation and grade control process;• the level of involvement of individuals and staff groups with computer-based ore reserve estimation;• the advantages perceived and realized from the utilization of computer-based ore reserve approaches;• the current and future human resources requirements for the evaluation, implementation, maintenance and development of computer-based ore reserve systems;• the hardware and software resources presently used and planned; and• the developments needed to increase the use and acceptance of computer-based ore reserves."

Jan 1, 1990

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By M. J. Latva-Kokko

This paper describes the behaviour of iron and the methods used for iron control in the nickel matte leaching process. OMG Harjavalta Nickel Oy processes approximately 10 000 t/y of iron, which enters the process with the nickel matte raw material. Iron dissolves and precipitates in several different stages of the leaching process. Compounds like ferric hydroxide, parabutlerite, goethite, hematite and jarosite are found. Iron removal is done within the leaching process, and this means that the dissolution of nickel sets the limiting conditions for iron precipitation. A leach residue consisting mainly of the iron precipitates is neutralized and stacked in the waste pond. When iron is precipitated from concentrated nickel sulphate solution, some nickel is lost by co-precipitation. Recent studies have shown that Ni-Fe ratios less than 1%, attributed to co-precipitation, can be obtained with jarosite precipitates, compared to 2-3% ratios typically found with hematite precipitates. Iron can be precipitated as jarosite under the optimal nickel leaching conditions by adding ammonium sulphate to the feed slurry of the autoclave.

Jan 1, 2006

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By T. H. Peters

The historical development of this program, dating from the construction of Nickel Park at Copper Cliff in 1917 to the various current projects carried out in the Ontario Division's program, is reviewed. Practices used to grow vegetation on stressed areas, the beneficial aspect of the improved aesthetic appearance of company properties from the point of view of public relations and the improved approach to the workplace by the employee are discussed. The revegetation of the tailings area and its gradual transformation into a Wildlife Management Area is reviewed.

Jan 1, 1978

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Constrained groove pressing (CGP), as a severe plastic deformation (SPD) technique, is one of the applicable methods for sheet metal forming capable of producing ultra-fine grained materials (UFGMs). In CGP, processing and die design parameters can significantly affect the deformation response of sheet metal specimen. Having said this, in the present research the effects of die design variables and processing parameters (i.e. shear angle and friction) on the deformation behaviour of an Al-Mg-Si Alloy are studied thoroughly. Finite element analysis (FEA), was used to evaluate the effectiveness of mentioned parameters on the deformation homogeneity, strain distribution and pressing load variations. Also, mechanical properties of the deformed sample in term of micro-hardness was analyzed. It is observed that with increasing the shear angle, effective stress, strain and pressing load are enhanced. Moreover, by increasing the coefficient of friction, pressing load enhances. The color coded micro-hardness measurement showed a good agreement with the strain distribution obtained from FEA (higher hardness for the zones associated with higher shear plastic strain values).INTRODUCTIONWork hardening results in enhanced mechanical properties upon cycles of deformation (Hosford & Caddell, 2007). However, the formability of the processed products are affected by work hardening reducing the possibility of processing in subsequent deformation cycles. Therefore, many industrial processes cannot be performed on sheet metals to produce products with desired mechanical and physical properties (Valiev, Islamgaliev, & Alexandrov, 2000). Severe plastic deformation (SPD) is an effective grain refining technique which can impose large plastic strains through cold working on a metallic specimen (Bisadi, Rastgou, Payganeh, Zeynali, & Ghahremani, 2010). SPD techniques are mainly categorized into three types; sheet, bulk and tube forming. Among SPD sheet forming methods, Constrained Groove Pressing (CGP) (Shin, Park, Kim, & Park, 2002), Accumulative Roll Bonding (ARB) (Saito, Tsuji, Utsunomiya, Sakai, & Hong, 1998) and Repetitive Corrugation and Straightening (RCS) (Zhu, Lowe, Jiang, & Huang, 2001) possess potential applications in manufacturing industries."

Jan 1, 2016

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019