Search Documents

By E. Herrera Alarcón, L. Mariscal Samaniego

The Teniente Converter (wet charge type) was commissioned in august 1995 and was designed to smelt 744 tpd (metric tons per day) of dry copper concentrates. Its products are white metal (73% Cu) that is sent to the Peirce Smith converters, slag that is cleaned in Reverberatory Furnaces and the process gases that are sent to the Sulfuric Acid Plant. Since its start up, the Teniente Converter smelting capacity was increased 1.6 times, from 800 tpd to 1,280 tpd using 33% oxygen-enriched air, and reaching an operative availability of 97%. By the other hand its campaigns have reached a record duration of 530 days without hot patching tuyeres and a partial refractory lining repair in the last four campaigns. This paper describes the most relevant improvements, as well as the strategies that had been used to reach these achievements.

Jan 1, 2007

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By M. F. Goudge

MAGNESIA refractories and magnesium metal are both essential war commodities. The need for magnesium, which had just made its debut as a commercial metal a few years before the outbreak of the present war, is widely known because this new and valuable light metal has already received much publicity. Less widely known but equally important in the war effort are magnesia refractories. They are indispensable to the efficient functioning of the great metallurgical plants producing steel, nickel, copper, and other metals, where, because of their resistance to extreme high temperature and chemical attack, they are used in lining the furnaces, which are operated at a white heat. The demand for refractories in the metallurgical industries rose rapidly upon the outbreak of war, and now, in consequence of the continued great expansion under way in the manufacture of steel, nickel, copper, and other metals, the need for magnesia is greater than ever. Since 1915, part of the Canadian requirements of basic refractories has been supplied from the deposits of magnesitic dolomite in Argenteuil county, Quebec. The products from these deposits are excellent for many uses, but the magnesitic dolomite has too high a content of silica and lime to be used in making a type of magnesia brick required in nickel converters, and in the roofs of reverberatory furnaces used in the copper and steel industries. There is now a large and growing demand in Canada for bricks and shapes for these uses. This demand has always been supplied from the United States. Makers of these products in the United States, in turn, formerly imported most of the necessary high-grade, dead-burned magnesia from Austria and Manchuria. Not only are these sources closed, but refractory chrome ore from the Philippines is no longer available and chrome refractories may have to be in large part replaced by magnesia.

Jan 1, 1942

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

By Afshin Sadri, Wai Lai Ying, Brycklin Wilson, Zoe Coull

"Although there have been great steps forward to integrate corrosion engineering into operations, there is still an underlying tendency for maintenance tasks to be performed in a reactive manner. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify leading indicators of failures. Prevention is generally less costly than repairs; moreover, when paired with appropriate monitoring techniques, intervention of corrosion protection can be more effectively timed and based on more accurate data. Hatch asset reliability studies show nearly 80% of defects are introduced through operations and maintenance. Therefore, proactive corrosion management can provide the necessary feedback to optimize operations and maintenance strategies preventing costly corrosion losses. Understanding corrosion risks gives a clear picture of the benefits of a proactive approach to asset performance. Monitoring techniques (Non-Destructive Testing, field testing, sampling, etc.) by nature are a more effective means of improving maintenance efforts and preventing corrosion losses than other methods (RCA, FMECA). This paper will outline the importance of proactive corrosion management and demonstrate its benefits through industry examples.INTRODUCTION Over the past few decades, with the growth of technology and awareness of sustainable development many studies have shown the benefits of a proactive approach to maintenance strategies. However, in practice there is still an underlying tendency for maintenance tasks to be performed in a “reactive manner”. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify defects and leading indicators to failures."

Jan 1, 2017

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By J. B. Keast

Introduction The last two or three decades have been marked by striking developments in methods of mining and tunnelling. In view .of increased competition and various economic factors, intensive ' mining has been largely practised, and no effort seems to have been spared to increase outputs and lower the cost of production. In metalliferous mining, the compressed-air rock-drill has effected marked savings in this direction, while in coal mining, the coal-cutting machine has revolutionized mining methods and materially contributed to economical working. Yet, for many years, little or no advance was made in methods of handling the rock, or coal, once it had been successfully broken. Loading by hand is, undoubtedly, the most laborious occupation in the whole of mining operations, and it is also the greatest single item that enters into the cost of production. In view of this, the lag of improved handling methods behind the process of winning the rock or coal is rather surprising. The point, however, was appreciated by mining men, and the introduction of various forms of conveyors and loaders is the result. The belt conveyor, the chain conveyor, the shaker conveyor, and the mechanical shovel entered various parts of the field, but it was left to scraping to provide a method of both conveying and loading. From the pure loading point of view, the choice lies between mechanical shovels and scraper loaders. While it is realised that each of these machines has applications peculiar to itself, yet it should be realised that much work which has hitherto been done by mechanical shovels can be done equally effectively with scraper loaders and at a considerable saving both from the point of view of initial outlay and upkeep.

Jan 1, 1933

By B. M. Monaghan

"The developments of the 1950s and 1960s have seen Canada become an international source of iron ore, trading in all geographical areas and hemispheres. Canada's production will significantly increase in the next decade. However, although the outlook is bright, iron ore producers cannot be complacent. Instead, we must weigh the factors that have brought about the development of the Canadian iron ore industry and examine the probable changes for the next decade that will affect its growth.Looking ahead in the 1970s, competition will be severe. Pressure on prices will continue as new sources of supply bid for long-term contracts and as steel producers continue to develop mines around the world. Rising costs will make these pressures more severe. We must balance the growth of the world's steel makers with the emergence of new supplies of iron ore. The iron ore industry is now part of a new era in which demand and supply are intermeshed, and the developments around the world are acting on the Canadian iron ore industry's future."

Jan 1, 1971

By W. J. Asselstine

Introduction This paper is prepared from data gathered for a similar paper to be submitted to the United States Bureau of Mines, for publication as one of their information circulars. It covers the history and development of the present milling practice at Premier. The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by D. L. Pitt, Manager of the Premier Gold Mining Company, Limited; also their indebtedness to various members of the Engineering Staff and of the Accounting Department who have assisted materially in gathering the data used. Location The Premier mine and mill are situated in northern British Columbia, approximately fifteen miles north of the head of Portland canal, in the Salmon River section, about half a mile east of the Alaska-British Columbia boundary line where it crosses die Salmon river. The mill is located on a rather steep hillside on the horizon of the main haulage level of the mine, and is within a hundred feet of the mouth of the tunnel. Both the mine and mill are connected with tidewater at Stewart, B.C., by an aerial tramway (1) eleven and one-half miles in length, which delivers both ore and concentrate to the bunkers at the dock for shipment to the smelters. All mine and mill supplies are transported from Stewart dock to Premier over this tramway, except heavy machinery. Heavy pieces have to be hauled either by truck in summer or sleighs in winter over a good road which runs from Stewart dock to Premier.

Jan 1, 1933

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By J. R. Smith

"The Lake Dufault orebodies were discovered by deep surface diamond drilling. When a reasonable amount of outline drilling had been completed, the decision to go into production was made. The fact that shaft sinking, lateral development, the detailing of the orebodies and stope preparation were to be carried out as rapidly as possible necessitated very close scheduling.After a study of varions possible mining methods, an open-stoping system using long-hole blasting was chosen. Diesel-powered Transloaders were selected for the mucking and transportation of ore from the drawpoints to the orepass.At the time of writing, the choice of mining method appears to have been fully justified, although more time will be required to arrive at true operating costs and efficiencies."

Jan 1, 1966

By E A. Mitchell

In the fall of 1961, Cominco dis-carded its long-established system of feeding the lead blast furnaces by narrow-gauge tram and V-cars, and installed an elevated monorail bucket system. This system automatically loads buckets of sinter, along with the correct proportion of coke, and delivers them to any of several designated furnaces. Direct labour usage has been reduced by nine men per day; improved coke proportioning has been achieved; and a major safety hazard has been eliminated. Introduction I N THE fall months of l 961. the system of feeding the lead blast furnaces at the Trail, B.C., smelter of The Consolidated Mining and Smelting Company of Canada Limited was altered from the tradition-al narrow-gauge railway and V-car method to one employing mono-rail carriers. The change was in keeping with a recent trend at Trail to replace narrow-gauge tramming with alternative methods of materials handling. In the case of the blast furnace feeding, the

Jan 1, 1963

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By L. Trytten, S. Bass, P. Nawrocki, J. Mercer

The Sherritt Fort Site nickel refinery and fertilizer plant has been operating continuously since 1954. The ammonia leach process uses ammonia and sulphuric acid, producing nickel and cobalt and an ammonium sulphate byproduct. One of the features of an ammonium sulphate based process is the aggressive nature of ammonium sulphate to concrete and structural steel. After six decades of operation, portions of the structural steel and concrete at the Sherritt facility have become degraded. Infrastructure replacement programs started in earnest more than a decade ago with pipe racks and electrical infrastructure, and have now progressed into building steel. Replacing and repairing this infrastructure within the tight constraints of an operating plant poses several difficult challenges. This paper will outline the approach taken to accomplish this difficult work, and discuss key learnings from the ongoing program.

Jan 1, 2015

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969