Search Documents

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By Y. M. Shneerson, E. E. Zhmarin, E. M. Vigdorchik

One of the Gipronickel Institute activities is research and development of customized leaching technologies. The work is performed in several steps. Leaching kinetics are studied on a lab-scale according to a special procedure. Experimental data are processed using mathematical models of batch and continuous processes. Reliability of kinetic data and preliminary calculations is verified experimentally in laboratory reactors of various capacities. If necessary, certain parameters of the mathematical model are adjusted after pilot plant tests in continuous mode ( 4-reactor train, each with 25 L capacity). The specified kinetic characteristics along with the mathematical model are used for further development of industrial leaching technology.

Jan 1, 2005

By J. F. Wright

The cold, or Kississing, Lake area in northwestern Manitoba was the scene of considerable prospecting and mining activity last summer. At the Sherritt-Gordon property, four diamond drills were at work exploring a large deposit of copper and zinc ore, and underground work was in progress on this deposit from two shafts. Some preliminary diamond drilling was completed in five other deposits, and surface exploration work was in progress at a dozen or more additional localities where copper and zinc sulphides were known to be present. Many prospectors visited the area and spent some time in search for new deposits, but apparently few discoveries were made; consequently, last autumn some returned a little disappointed in the area as a prospecting field. Although many visited Cold Lake area last summer in the search for mineral deposits, it should be emphasized that this new prospecting field is a very large one, and that to date only a small proportion of the ground has been examined, except in a very general way. Within the past 18 months, a village of several dozen cabins, and with a population of l00 or more persons, has sprung up on the shore of Cold lake, just west of the Sherritt-Gordon mine. This at present is the business centre of the area, and two banks, a post office - named Kississing by the Postal authorities - a Mining Recorder's office, as well as several restaurants and stores carrying a fairly complete stock of groceries, dry-goods, and general prospecting equipment, are already established.

Jan 1, 1929

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By J. H. D. Hargrove, A. F. Snowball

Atmospheric pollution control has become increasingly important in re-cent years with laws and public opinion having required the reduction of contaminants from industrial gas effluents. Treatment methods have advanced to make possible, with proper plant design and operation, a satisfactory removal of these contaminants. Gases from Cominco's metallurgical operations at Trail, approximating 900,000 c.f.m., are treated by baghouses, electrostatic precipitators, cyclones, or wet scrubbers. The tabulated data include gas and dust conditions, plant performance, and some details of plant equipment. Discussion emphasizes the special features, scope of application, and basic design principles of the treatment methods, all based on Cominco experience. Recovery of over 99 per cent of the fume and dust is achieved by the major installations from which effluent gases go to atmosphere. Cooling of gases for baghouse recovery and conditioning for electrostatic precipitation are mentioned. Co3ts are tabulated for some of the installations on the basis of a unit of 1,000 cubic feet of gas. Suggestions are made on the procedure for assessing a smoke treatment problem and for selection of suitable equipment.

Jan 1, 1959

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.  This is the result of the social and financial accountabilities that the industry is faced with because of the world’s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).  To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.  In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.  It follows that comminution is the major greenhouse gas emission process of the mine.  All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.  In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.  This paper makes a definitive contribution to that discussion.  The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.  Major emission contributors, steel, natural gas and electricity are discussed in detail.  The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.  The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.  Emerging steel making technologies are presented and discussed.  The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.  Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.  The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.  Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013