Search Documents

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man's involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By S. Beitler

The availability of renewable energy does not meet the demands of consumption. Hence, fossil fuels will continue to be an important energy source, and coal promises to cover the requirements for the coming decades. Because of its high energy content, deep lying bituminous coal and anthracite are important for energy generation. One trend in the future of coal mining is thin seam mining, because thick seams more and more have been exploited. A well-known and approved longwall mining method for thin seams is plowing which has big advantages compared to a shearer because of its compact design. The extraction of those thinner coal seams will become more and more important in coal industry and therefore the plow will receive more attention in future. Most approaches in longwall automation are focused on the shearer and need a more or less intelligent exploitation machine. Therefore those approaches cannot be used for the plow technology. The authors introduce a shield-data-based horizon control (SDHC). The developed approach integrates the shield data provided by the roof support and process monitoring into the horizon control process to keep the plow in seam even if the seam trend changes. This control concept can be used for the shearer as well as for the plow. The basic idea of SDHC for plow application will be introduced in this paper and first simulation results will be shown.

Aug 1, 2013

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By Anthony J. Deevy

"Abstract -The Magino gold mine is located 45 km northeast of Wawa, Ontario. There was limit­ ed gold production in the Iate thirties. The present operation was officially opened in October 1988 and produced gold until September 1992. It was a 635 tonnes per day, decline-accessed mine, with ore coming from several small blast hole and shrinkage stopes.The host for the gold is the Webb Lake granodiorite stock which was intruded into the Goudreau Lake Deformation Zone. This east-northeast-striking deformation zone overprints the generally east­ west-striking isoclinally folded metavolcanic and metasedimentary rocks, which make up the east end of the Michipicoten greenstone belt. The ore-shoots are controlled by dextral delatancy associated with the Goudreau Lake Deformation Zone. Shearing, bleaching and silicification accompanied the gold emplacement."

Jan 1, 1994

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By Maciej Wrobel, Joerg Hammerschmidt, Dana Nurgaliyeva, Alexandros Charitos, Jochen Guentner

"Smelting of copper concentrates in the flash smelter generates a flue dust stream that contains a substantial amount of copper and accumulates more than half of the arsenic input to the smelter. In view of its high copper content flue dust recirculation to the flash smelter is common practice. Globally traded copper concentrates are affected by ever increasing arsenic contents and cause an increasing circulating arsenic load in flash smelter operation. Control of the arsenic level in the smelter slag becomes a challenge. This interaction of arsenic loaded copper feedstock, need for flue dust recirculation and slag quality control call for possibilities to reduce the arsenic load of the recirculated flue dust stream.The technology of partial roasting is known from pre-treatment of copper concentrates before smelting, and gold concentrates before cyanide leaching, to remove the harmful element arsenic. The partial roasting technology can be adapted for use in the purification of the flue dust. A major challenge for flue dust treatment is its extremely fine particle size compared to usual concentrates. For this reason Outotec developed a new process, which allows handling of such fine flue dust. This process solution provides an efficient possibility to reduce the arsenic burden in copper smelter operations.The suggested process aims at reducing the arsenic load to the smelter by treating the flue dust prior to recirculation to the smelter. The presented results are based on test work in the Outotec R&D-centre in Frankfurt. It is possible to remove 80-85% of the contained arsenic and to collect it in an arsenic trioxide residue with a concentration above 90%. The final off gas contains SO2 from decomposition of sulphates that are contained in the flue dust. The off gas stream is relatively small. We assume that it is possible to combine the off gas stream with other smelter process gas streams and to treat it in an existing sulphuric acid plant. Coal is used as fuel and as reductant to reduce pentavalent arsenate to trivalent arsenite. Arsenite can be kept in gas form at temperatures above 450°C. This permits separation of a calcine stream with arsenic levels of 0.2 – 0.3%, which is recirculated to the furnace.Outotec has a wide range of roasting testing facilities from lab-scale to pilot-scale. Outotec has both capability to modify and adapt technology to specific ore or concentrate requirements, but also the necessary infrastructure in its research centers in Frankfurt and Pori to do appropriate validation tests in lab and pilot scale size plants."

Jan 1, 2016

By T L. Horsley

The change from a seasonal to a continuous mining operation at Cassiar has been accompanied by increased emphasis on the preventive maintenance of mining equipment. This paper describes how equipment maintenance is organized, and details some maintenance practices that have proved advantageous to the Cassier operation. Introduction Cassiar Asbestos Corporation Limited is currenly carrying out an open-pit mining operation at the 6,300-foot elevation on McDame mountain in northern B. C. A 6-mile road connects the mine to the mill and plantsite at the 3,500-foot elevation. Ore concentrate is delivered to the mill via a 3llz-mile tramline. Naturally level ground does not exist in the mine area. The weather is typical of mountainous regions, exhibiting wide and rapid variations in temperature. It is generally wet and windy at the mine elevation, and a heavy snowfall is common. The rock types vary from a soft, sheared serpentine to massive serpentine, to medium-hard, friable sediments to hard, blocky volcanic flows.

Jan 1, 1964

By N. Ahern, L. Manoukian

"Cyanide is a leaching agent for precious metals commonly used in gold ore processing. Cyanide exists in various forms (including free, complexed as weak or strong complexes, and as ions such as cyanate and thiocyanate), so its detection, speciation and analysis in processing or environmental samples can be complex. This paper will review best practices for cyanide sampling and preservation in the field, interferences and pretreatment methods required prior to sample analysis and analytical methods that are used for cyanide species. Titrimetric, flow injection ligand exchange, spectrophotometric, colorimetric, potentiometric, amperometric, and chromatography techniques will be discussed and their chemistries, detection limits, advantages and limitations will be described.INTRODUCTION Cyanide is well known to be an extremely toxic species. Accurate cyanide measurement in effluent from mines is critical from an environmental perspective. Its measurement is also an important control parameter in the recovery of gold using cyanidation. Cyanide chemistry is diverse and complex, and cyanide analysis can be challenging as a result of and because of limitations in understanding of analytical methods. Various chemical mechanisms can form or destroy cyanide, and the sample matrix or preservation chemicals can also affect analytical results. These interferences make the collection of reliable cyanide measurements challenging and can start as soon as the sample is collected, during laboratory pre-treatment and during analysis. This paper reviews different methods of cyanide measurement. The basic chemistry of cyanide, best practices for sampling and preservation, as well as various methods of analysis will be discussed.CHEMISTRY The complexity of cyanide chemistry is well known (Beck, 1987; Delgado, Botz, Bucknam, Milasovljevic, & Staley, 2008; Botz, Milosavljevic, & Ward, 2013) and is attributed to the ability of cyanide to undergo: •,Volatilization •,Precipitation •,Adsorption •,Complexation with metals •,Oxidation to cyanate, ammonia, or cyanogen chloride •,Reaction with sulfur or sulfide minerals to form thiocyanate •,Redox reactions leading to the formation of cyanogen and cyanate •,Redox reactions (of some cyano complexes) •,Photochemical reactions (of some cyano complexes)"

Jan 1, 2017

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By H. R. Banks

SHORTLY after the commencement of operations at the Sullivan concentrator, the use of a pilot table was instituted in order to present a visual control of various products by showing the amount of galena still present in the tailing from several stages of flotation. Among the products so treated, the final tailing was later included. It was sratifying to note that very little free galena was escaping, but a fine streak o a whitish mineral appeared at the concentrate zone. This mineral was identified as cassiterite. The amount was small and the newly recognized component in an already complex ore was considered primarily as of academic interest. However, the problem of recovering a usable metal was intriguing and, as opportunity presented itself in temporary lulls in research on Sullivan and other ores, the concentration of tin was a useful 'bit of knitting' to go on with. It was recognized from the start that the bulk of the mill tailing would have to be floated and the residue subjected to gravity treatment. Since one of the predominating features of Sullivan concentration operation has been the necessity of fine grinding, the problem of gravity concentration was thereby intensified. Several batch runs were made, and sufficient pulp was treated to produce about one ton of final tin concentrate assaying 67 percent tin. The overall recovery was under 30 percent and the estimated profit at full tonnage was only marginal. Testing was resumed several years later, when the price of tin again appeared attractive, in an attempt to develop a more compact plant with better recovery of tin. The weakness of the original plan of concentration was the large number of tables required to treat a feed so low in tin.

Jan 1, 1941

"Many advances in glass technology and processing are being made and the possibilities for glass as a material in the future appear unlimited. Float glass, glass-ceramics, high-strength sheet and container glass, glass-reinforced plastics, glass for electronic equipment, aerospace glass, glass fibres, glass vehicles, glasses with selective-reflective coatings and glare-reducing glasses, to name a few, provide areas of significance at present and for the future. There appear to be great opportunities, in certain localities of Canada, to develop new sources of raw materials for an expanding Canadian glass industry.New developments in the structural clay products industry have centered around facing brick as a structural load-bearing material, prefabricated brick panels, large-sized units, isostatic pressing of sewer pipe and auto-matic settmg of brick. Fast-firing techniques, using prefired or calcined raw materials, and the development of high-strength products will result in the use of a wider range of raw materials in the whiteware and structural clay products industries.Porcelain enamel, a material used for many years in domestic appliances and for sanitary ware, now is used extensively in architecture, agriculture, water tanks, highway signs and reflectors, and in products where resistance to corrosion-plus-temperature is important. Exotic composites of ceramics and metals, and specialized ceramic coatings applied on metals by various techniques such as flame spray, plasma jet, or vapour and chemical deposition have proved useful in materials for aircraft power plants, rockets, missiles and nuclear applications."

Jan 1, 1967

By R. J. Hundermark, K. van der Merwe, L. R. Nelson

Taphole integrity is critical to all furnaces, but it is especially important in high intensity electric furnaces processing matte and metal of high superheat. Key furnace dimensions are the electrode proximity to the taphole, hearth sump below the taphole and the shape and location of the taphole in the furnace wall (e.g., circular versus rectangular furnace). In addition, electric furnace power density needs to be matched appropriately to any configuration to achieve operational reliability and furnace integrity. The role of furnace dimensioning is generically reviewed across many pyrometallurgical processes to explore potential impact on furnace taphole performance. Some empirical furnace dimensions and power density ratios of industrial furnaces are then compared to explore to what extent they may indeed influence taphole integrity.

Jan 1, 2015

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006