Search Documents

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013

By P. E. Cavanagh

THIS REPORT is not intended to be a ?comprehensive survey of the steel industry in Europe. For the past ten years the Ontario Research Foundation has been interested in several developments in the steel industry in Europe which it was felt would be of particular interest in Canada and might possibly find application in this country. This is an account of the present status of some of these developments. The economies of steel making in Canada are somewhat different than in the United States because of the nature of the market and the relative costs and availability of such raw materials as metallurgical coke and electric power. There are cases in Europe where a great deal of effort and money has been spent in trying to make steel profitably by methods which take advantage of locally available and cheap raw materials by modifying standard practices. ln cases wl1ere the investigations have been successful and the data are available to allow translation of the results into Canadian conditions, it is felt that such information may be of great benefit in the future in Canada and at !east should be known to all those in the steel industry in this country. The field to be covered in this report only comprises the steps from concentration and treatment of iron ores to production of iron and is only concerned with those commercially operating processes well known to us and judged to be of present interest in Canada.

Jan 1, 1957

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By M. D. Griffith

"Ventilation models are a vital tool to ensure ventilation designs can provide airflow to all work areas in a mine. Airway resistance and variations in natural ventilation pressures will affect simulated airflow and heat distribution through a mine. Validating ventilation model resistances and pressures to the exact underground conditions can be difficult and the variances can contribute to significantly different simulation results depending on the structure of the ventilation design. The study will use sensitivity analysis to explore examples of variability of simulated airflow due to small resistance, heat and natural ventilation changes and thereby help the user identify both trustworthy and potentially unreliable parts of a mine ventilation model. INTRODUCTION Mine ventilation network modeling is a vital tool for ventilation professionals and has become increasingly relied upon during the design and operation phase of mine ventilation systems. However, they provide only an approximation of reality, and caution must always be exercised when drawing conclusions or making decisions based on simulated data. Ventilation modelling should be performed by persons with a sound fundamental knowledge of ventilation and ideally should be validated with field data, but in large mines, or mines which are yet to be mined, accurate input of the simulation variables can be difficult, and errors and inaccuracies may be difficult or impossible to avoid. This study discusses and investigates the sensitivity of the mine ventilation simulation results to input errors. In addition, there are limitations to what steady-state airflow and heat simulations can model, regardless of the accuracy of the model inputs. In some situations, steady-state solvers cannot capture the dynamic changing behavior of a ventilation system. This study will also describe and apply techniques to analyze the natural variability of mine conditions on ventilation models. The consequences of poor accuracy in some parts of a mine model may impact on the health and safety criteria of ventilation designs. For example, if an airway is required to flow in a particular direction and quantity, then despite a ventilation model showing correctly designed conditions, small errors in input values may result in incorrect prediction of the direction or quantity of airflow. This may create unexpected buildup of heat or gases during operational activities, causing safety issues or operational delays. The ability to know which parts of a mine ventilation model have increased potential for poor simulation results will allow engineers to consider the ventilation design and make changes if required to better guarantee the required design flows."

Jan 1, 2019

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By F. Hampshire

"IntroductionThis paper is intended to cover questions raised by operating staff at various installations and is not intended to give comprehensive coverage of power plant and power system design. The paper is concerned mainly with the electrics , although a brief section gives the reasons for selection of diesels rather than other prime movers.The material is not new but brings out points which seem to be raised regularly during the design , commissioning and operation o f a new plant. Diesels versus other Prime MoversDiesel-electric plant for the mining industry falls into two major categories -emergency power and prim e power.1) Emergency power (for use only when the regular utility supply has failed) requires reliable starting and operation and reasonable first cost. Fuel economy and maintenance are of little importance as the machine(s) generate few kilowatt hours only. The diesel's competition in this field is the gas turbine, however diesels are more widely used than gas turbines in this application.2) Prime power is a different situation as the bottom line of total cost is highly affected by fuel costs.In general , mines which are within reasonable transmission distance of an existing utility find the lowest net cost result s from hooking up to the utility. If a min e is remote from an electric utility then the possible alternatives are:a) Hydro- electric power if there is a site capable of development at reasonable cost including the cost of transmission facilities. Such sites are not common, but brief and inexpensive considerationof this possibility is warranted .b) Diesel power with consideration of different grades of fuel.c) Thermal (steam) power generation from coal or oil.d) Gas turbines.In addition to the above there is the possibility of wind power (as a supplementary source) and a number of technologies which may become feasible in the future (e.g. small nuclear plants, fuel cells). For obvious reasons, small isolated generating systems required for remote mines, tend to lean to conservative technology.Among the fossil fuel plants, the diesel enjoys advantage on over-all costs as summarized in Table 1."

Jan 1, 1986

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By T. H. Janes

THE POSSIBILITY of producing pig iron from iron ores of British Columbia for a west coast primary iron and steel industry has been investigated by the provincial government and by commercial interests on sever.al -occasions. The latest study is that currently under way by The Consolidated Mining and Smelting Company of Canada, Limited. The Company is studying the possibility of making pig iron from the oxide calcine resulting from the roasting of pyrrhotite. tailings used in making sulphuric acid for fertilizer production at Kimberley. A comprehensive report on the subject .of establishing a primary iron and steel works in the Province, based on local iron ores, was prepared by Arthur G. Mc-Kee and Company of Cleveland, Ohio, in 1942 for the B.C. Minister of Mines and is available to interested parties. A detailed survey on the subject was also pre-pared in 1954 by Dr. G. P. Con-tractor, then .of the British Columbia Research Council. Considerable information is there-fore available on most aspects of an integrated primary iron and steel industry in British Columbia to supply the needs of the western provinces. To date, however, no basic iron industry has been established despite the .occurrence of high-grade iron ore deposits on the offshore islands and the high freight charges on iron and steel products brought into the area from Eastern Canada and overseas producers. The chief deterrent has always been the relatively small and highly diversified market available to a local steel producer. Other major fact-ors have been the lack of sufficient proven reserves of iron ore, and the difficulty of making pig iron, suit-able for steel manufacture, economically on a small scale. Technical and economic conditions have changed considerably since World War II and the establishment of a primary industry based on electric furnace production of pig iron or on one of the direct reduction processes, coupled with electric furnace steel production, may now be economically feasible.

Jan 1, 1958

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973

By J. H. Starkey, P. A. Scinto

"In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding – in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated.Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant.Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk."

Jan 1, 2012

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By S. Goodman

Successful exploration for and exploitation of a mineral deposit requires an accurate understanding of the deposit architecture in 3D, and of the development of the mineralizing system through time, which requires a thorough comprehension of the structural framework of the deposit. The integration of geological, geophysical and geochemical datasets to arrive at a 4D structural framework is well-established and has been successfully applied by SRK Consulting in projects from deposit to regional scale. In some cases, we can go beyond this, applying the SEEBASETM technique, which utilizes a ?bottom-up? approach to basin analysis. SRK?s approach primarily relies on the interpretation of magnetic and gravity data, calibrated with many other datasets including mapped geology, topography, event histories, wells/drillholes and seismic data. The SEEBASETM model is a culmination of this data integration and is produced through an iterative process of structural interpretation and geophysical modeling, where an interpretation of basement composition and 4D structure is used to constrain depth-to-basement geophysical modeling, and the modeled depths are then used in conjunction with the structural interpretation to constrain contouring of the basement topography. The result is a rigorously calibrated, 3D view of the basement surface, which can be used to understand the basement and basin architecture, and thus serves as a predictive exploration model. This technique, which was developed for use in the petroleum industry, is now finding success as a predictive tool in mineral exploration.

May 1, 2003