Search Documents

By J. G. Lang

"This paper gives an outline of the principles used in E.M. wire rope testing, showing the practical application of the device and its value in industry and in mining operations.It presents: case histories involving deterioration, such as corrosion, peening and broken wires; anomalies indicating conditions peculiar to drum hoists and friction hoists; tests of locked coil ropes; low-frequency testing; and experiments and development."

Jan 1, 1969

By D. J. Kemp

The 20th century saw changes in the mining and metallurgical industry not only technically but also in social and environmental expectations. As projects continue to become larger their visibility raises concerns among many groups. For mining companies, transparency, openness, and early engagement of all parties are fundamental to assure success. An equally important task is to anticipate the standards that will be required to meet society’s expectations in the 21st century.

Jan 1, 2005

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves' clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By R. C. Hartviksen, B. H. Boyum

"The Sherman Mine, Temagami, Ontario, is an iron ore pellet operation rated at one million tons per year capacity. Mining is done from three open pits in two bands of Keewatin iron-formation intercalated in a 'greenstone belt' thought to be part of the Archean 'Abitibi Belt'. The bands of iron-formation are tabular and steeply dipping, averaging 75 degrees. The principal ore mineral is magnetite.Blast holes, 1214 inches in diameter, are drilled on 28-foot centers, each hole being sampled and assayed for both total iron and magnetic iron. Concentration tests are made in the laboratory to determine the anticipated concentrate grade. Two classes of ore are recognized -'liberating' or 'refractory'. Blending is done on iron con-.tent, degree of ease of liberation (i.e. grain size) and chunkiness. The latter is important, as primary milling is done in autogenous mills. Actual daily mill results are compared with predicted grade from blast holes, exploration diamond drill holes and pit inspection. Hourly mill samples are analyzed by the X-Ray Fluorescent Analyzer, with emphasis on silica grade. In 1969, the pellet grade was improved from 7 .01 per cent silica natural to 5.50 per cent silica natural."

Jan 1, 1970

By P. H. Jennings, J. C. T. Farge

Commercial tellurium commonly contains heavy base-metal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities ( 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too slow to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Jan 1, 1966

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By J. Beddoes

Many high strength aerospace alloys undergo solution heat treatment (SHT) and aging to develop precipitate strengthening. Most simply, SHT involves an isothermal hold in a single phase region followed by relatively rapid cooling to develop a super-saturated solid solution from which precipitates form during aging. However, subsequent properties are sensitively dependent on the details of the SHT, which frequently also serves a homogenization function. Altering the details of the thermal cycle during SHT significantly improves the properties attained during aging, as presented by examples of SHT design for titanium aluminide intermetallics, polycrystalline and single crystal superalloys, and 7075 aluminum.

Jan 1, 2010

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003